Question about Mitsubishi WD-52525 52" Rear Projection HDTV

1 Answer

Blue Screen & inputs dont work.....capacitors?

Hello everyone,

I was watching TV last night via HDMI and the screen started to scramble at 720p, i dropped it down to 480 and it started to work again, but it eventually scrambled too and went to a blue screen. Now none of the inputs seem to be working (Component & Input).

Could this be a capacitor problem? I seem to be reading a lot about it here, if so where can i get instructions on replacement. I do not have a problem taking the TV apart and soldering.

If it is not a capacitor, what could it be?

Thank You for all the help!

Posted by on

  • SoCalHeli Aug 07, 2008

    Just noticed horizontal lines (Light Blue) & when i change inputs there seems to be a starry sky appearance.

    Also, problem seems to be progressing, now even the menus dont show up properly & wiggle vertically.

    Thank You


  • SoCalHeli Aug 19, 2008

    does anyone have any input? please help....

    socalheli@hotmail.com



×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

I had the same problem, I called Mitsubishi and they with trouble shooting help, they told me to get a new lamp. Well I got a new lamp and but nothing happens, the tv screen is black no sound, no picture. I went to this site http://servicemanuals.vstore.ca/product_info.php/pName/v26-dlp-fmt-pwb-repair-kit/cName/repair-kits/osCsid/5ac56adb48ff3afdd7ff25c1f1f5cbf2 and with their help, and troubleshooting help, said this kit would work, I just got it today,and I am going to install it now, I will be back to let you know. But I do suggest you go on that site, and try to get some assistance, they sell the service manuals for 16.99$, but if you buy a kit, it includes the manual. Well let us know what happens, and I will be back.

Posted on Aug 08, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i hook up my ps3 with tv through hdmi as it keeps goin to blue screen


  1. Connect the PS3 standard composite video connector (yellow RCA plug) to the TV composite input and switch the TV to that input. Leave the HDMI cable connected.
  2. Make sure the PS3 is off. Turn it on and hold the power button until you get two beeps (at least 5 seconds). The PS3 navigation screen should be shown on the TV. If not, switch the TV back to HDMI; the screen should be displayed at 480i resolution.
  3. Go to the settings menu. Select Display Settings, then Video Output Settings, then press the X button on your controller.
  4. The on-screen instruction should be "Select the type of input on your TV." Select HDMI, then press the '> (solid right triangle) button on your controller.
  5. You will be offered the choice of Automatic or Custom settings. Try Automatic first (if there is a problem at the end, start over and pick Custom the second time).
  6. Press the X button. You will get a screen asking you to confirm the changes. Press the X button again to confirm.
  7. You may get a screen asking for the resolution setting. IMPORTANT: if your TV's maximum resolution is 720p or lower, do not pick a higher resolution. The TV may not display properly or may not display at all (blue screen). Pick the highest resolution your TV can display.
  8. Confirm this by selecting "Yes" and pressing the X button.
  9. The settings list should now read Connector Type HDMI; Resolution Standard (NTSC); 480p; 720p; 1080p (if applicable). Press the X button to confirm.
  10. You may be offered a choice of audio outputs; you can use HDMI or something else, depending on your setup. Confirm the setting and press X one more time.

At this point, the PS3 should send its signal to the HDMI port following restart. If your TV has more than one HDMI input, make sure you select the one connected to the PS3.

Mar 12, 2011 | Televison & Video

1 Answer

I cannot watch cable TV on Input 1 when Input 2 is activated.


Tries to reset the tv Tuner board back to factory setting.By go into the tv menu.Go to PICTURE,go down to reset the Tuner board.All the HDMI ports should work now.Not,than the HDMI port 2 is shorted and dead,don't used the HDMI port 2.The tv should work fine,or tries websites like Shopjimmy.com,Ebay.com to buy a refurbish Tuner board for the replacement.

Jun 16, 2010 | Sharp Aquos LC-45GX6U 45 in. HD-Ready LCD...

3 Answers

Onkyo TX-SR606 takes up to 30 minutes to display 1080p


Please don't rate me for this. Onkyo has been having voltage problems with their HDMI boards in several models. Yours is one of them. They first instructed techs to replace some capacitors, then add some capaictors to repair the voltage problems. Now they want us to replace the HDMI boards but I have yet to receive any (on back-order) Sorry for the bad news.

Mar 23, 2010 | Audio Players & Recorders

1 Answer

Onkyo TX-SR706 Setup Display Problem


For adjustments to receiver you can always run a component or composite cable to your plasma tv. After adjustments are made just return to HDMI input.

Feb 24, 2010 | Audio Players & Recorders

1 Answer

I have a Sharp 32 inch 720p tv, power works, no other buttons do


Unplug TV set from the outlet, wait 30 seconds, plug it back in, select right input with your remote if you using cable box or Punch the channel that you want to watch if you have cable service connected directly to the TV.

Nov 05, 2009 | Sharp LC-32SB23U 32 in. LCD TV

1 Answer

Problem with component input and 720p HDMI output


does your cable box have an hdmi output? if it does try an hdmi cable instead of componant cables[ i know the hdmi cables aren't cheap] if not, if the reciever has componant outputs, use them instead.
hope this helps
wg

Feb 02, 2008 | Onkyo TX-SR605 Receiver

1 Answer

DVD movies do not play


A blue screen means the TV is not receiving a video signal. Check all connections, then try another player, cable, etc. Also, check DVD and TV AV settings.

Dec 10, 2007 | Pioneer VSX-D912 Receiver

3 Answers

Screen flicker when watching 1080i


Component video has a max resolution of 720p. in order to use 1080i or p you have to use hdmi or dvi connections. That is why you get the flicker.

Dec 08, 2007 | Onkyo TX-SR304 Receiver

Not finding what you are looking for?
Mitsubishi WD-52525 52" Rear Projection HDTV Logo

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1207 Answers

The Knight
The Knight

Level 3 Expert

71006 Answers

Jaime Hernandez

Level 3 Expert

2271 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...