Question about LG 37LC2D Television

1 Answer

Remote control no response

I get no response from the factory remote control. I have had the TV for 15 months or so.

Posted by on

  • 1 more comment 
  • Anonymous Oct 13, 2008

    Where can you buy a replacement remote? I live in Canada (Toronto).

  • 3greencobra Nov 28, 2008

    Same here, TV and DVD remotes work on other products, but not the TV...

  • 3greencobra May 11, 2010

    How do you test IR detector?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 934 Answers

Have you tested the remote? Get a cheap IR reader card, Radio Shack used to have them, and test the remote. If it's working test or replace the IR detector in the Tv... If both of these are working you'll need a schematic and a logic probe to test the micro or you may need to replace the main cba P/N 33139d3029a
Good Luck!
Bill

Posted on Aug 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When I Turn My Samsung Led ua32f4000ar On With The Remote Control The Power Led Turns Off And Nothing Else Done No Response From The Remote Control Until I Take Off The Plug And Put It Again,plz help


Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/ In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.
Before going further; try a hard reset first. If it does not help you, replace the main digital board. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; visit the site linked here.

Oct 08, 2016 | Samsung Flat Panel Televisions

1 Answer

Sharp LC-26AD5E-BK Upon switching TV on screen displays: "Software Update through PC/UART" & "Connecting to host". TV is non responsive to remote control and am unable to exit screen. Please help.


Try a hard reset to this set, and then check. If it do not help you; contact the authorized service center for sharp. Firmware update might be necessary.
There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/
Service mode entry, adjust and exit procedure to many popular brand TVs are given. Never forget to exit the service mode, after all adjustments have been done.

Jun 15, 2016 | Sharp Flat Panel Televisions

1 Answer

How do I reset my tv without remote control?


Without the remote control, you can not do a factory reset; Can only of the hard reset. There are two methods to reset TVs. The first is simple to do; Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it to reset system [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the website linked here. Pull up older posts. Http://electronicshelponline.blogspot.com/
Service entry mode, adjust and exit procedure to many popular brand are given Beheerder TVs. Never forget to exit the service mode, after all adjustments Have Been done.

Jun 09, 2016 | Flat Panel Televisions

1 Answer

Suddenly the tv box mk4 en remote stop working.


Check the remote control for its infra-red emission. Check it with fresh batteries. Check by pressing all the buttons on it; and see whether all of it generates infrared signal while pressing. If it is found OK, check and replace the infrared sensor inside the TV. If you wish to get some details; check the site linked here. It has details about how to check a remote control; by one among the post. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/
If the remote control is found OK; check and replace the infra-red sensor inside the TV. Contact any service technician.
Try a hard reset or a factory reset too; if the remote control is OK.
There are two methods to reset. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked above.

Jun 04, 2016 | Flat Panel Televisions

1 Answer

My Thomson digital tv recorder 500GB DT16021TUT is not taking commands from remote control after freezing when trying to set timed recording


First of all, check the remote control handset for its infrared emission. If found OK, try a reset to this set, and check further. Check the remote control for its infra-red emission. Check it with fresh batteries. Check by pressing all the buttons on it; and see whether all of it generates infrared signal while pressing. If it is found OK, check and replace the infrared sensor inside the TV. If you wish to get some details; check the site linked here. It has details about how to check a remote control; by one among the post. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/ If the remote control is found OK; check and replace the infra-red sensor inside the TV. Contact any service technician
There are two types of reset to TVs. The first is simple to do; a Hard Reset; and the other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight; will be better. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked above.

Jan 30, 2015 | Thomson Flat Panel Televisions

1 Answer

How to PCB reset hitachi 42 " plasma tv i dont have the remote and the panel button lock is set on...so the panel buttons wont work.... Any way to fix it ?


Without its remote control, you can't make a reset to this set. In fact; a hard reset procedure do not want a remote control, but,. if you wish to make a system reset [Factory Reset]; there is no other way without a remote control.
There are two types of reset to TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight; will be better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/
Service mode entry, adjust and exit procedure to many popular brand TVs are given. Never forget to exit the service mode, after all adjustments have been done.
To get more details about remote controls. visit these sites.
Remote Control Codes
Electrohelponline

Nov 25, 2014 | Flat Panel Televisions

1 Answer

How factory reset LG 3d TV


To do a factory reset to all LG brand sets, you should have a factory remote control [not the remote control supplied with the TV]. You can buy it from authorized service centre for LG. There are two types of reset to TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight; will be better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/
Service mode entry, adjust and exit procedure to many popular brand TVs are given. Never forget to exit the service mode, after all adjustments have been done.

Nov 06, 2014 | Flat Panel Televisions

2 Answers

Hi there I have a 20" Humax IDTV - LU20-TD2, it


Look for any jammed buttons on the remote or on control panel. Try changing the input device to something that you are sure, works.

Jul 29, 2012 | Flat Panel Televisions

1 Answer

I am having trouble getting a remote control to work with this tv. can you help?


Change batteries,clean the front tv sensor light,and on the remote.All this done,still not working ur remote is dead.Try 1-800-Romotes Factory original.Buy an exact remote.

Feb 10, 2010 | Philips Magnavox 15MF400T 15 in. LCD...

1 Answer

I have lost my remote control for my rca mikomi


Try Website 1-800-Remotes Factory original.Get the same or very close to it.

Dec 02, 2009 | RCA Mikomi 5290925 15 in. LCD TV

Not finding what you are looking for?
Flat Panel Televisions Logo

144 people viewed this question

Ask a Question

Usually answered in minutes!

Top LG Flat Panel Televisions Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18299 Answers

The Knight
The Knight

Level 3 Expert

68352 Answers

Are you a LG Flat Panel Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...