Question about Projection Televisions

1 Answer

Tv turns off and on by its self and volume goes way up.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 927 Answers

GOOD DAY, GREENFLOWER;

TRY UNPLUGGING THE TV FROM THE WALL OUTLET FOR 3 - 5 MINUTES.....PLUG BACK TV BACK INTO WALL. NO FIX?

THEN IT IS TIME TO CALL AN AUTHORIZED SERVICE CENTER TO COME OUT TO YOUR HOME AND GIVE YOU A WRITTEN ESTIMATE.

GOOD LUCK BIG IRISH.

Posted on Aug 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mitsubishi big screet HDTV after being on for a minute, the scree pops and goes black with some red lines, then the volume turns all the way up by itself.


Do the self check----if set has been unplugged plug it in and turn on for it to fail----when it shuts off ON THE FRONT OF THE SET press and hold both the menu and input (device) buttons at same time for at least 5 seconds and release both.

Power light will blink a two digit error code like, 1 blink, 2 blinks and pause and repeat it for a total of 5 times.

What if any error code do you find?

Jun 16, 2012 | Mitsubishi WS-55513 55" Rear Projection...

1 Answer

Power light is green than goes red


Hi beinhauert,

The symptoms you've mentioned indicated that the unit turned to standby mode. This is an indication that there's something wrong on the TV. To help us narrow down where the fault came from, please access the built in "Self diagnostic Screen". Follow the steps below.
In standby mode (red light is on), press the button on the remote control in sequence "Display", "5", "Volume (-)", "Power". Self diagnostic screen's displays its log of error. Please let me know the error code with corresponding numerical value "1" means error has been detected, "0" means no error.

Jdvillanueva

Jan 06, 2012 | Sony Grand WEGA KDF-60WF655 60" Rear...

1 Answer

Panasonic tv turns volume down by its self


there might be something wrong with the tv remote. turn the tv on then make it on a high volume then put the remote in a different room and see if the volume turns down if it doesn't then you have some thing wrong with the remote not the tv.

Jan 15, 2011 | Panasonic PT-50LC14 50" Rear Projection...

1 Answer

My tv has got to where the volume goes down on it's own, the menu screen pops up all the time, and the tv has turned it self on once.


this is farely comon i see this all the time at the shop... you have two options replace the keyboard cuircit board. or disconnected and just use your remote to control tv. of coarse you can remove the board until you get a replacment

Dec 14, 2008 | RCA R52WH76 Television

1 Answer

The volume to the tv goes to max when you turn it on?


that hapened because your remonte contral has the + button pressed just release the volum + at your remonte and all will be ok
or try to hide your remonte control and get down sound from front panel of your tv

Dec 11, 2008 | Projection Televisions

1 Answer

Picture/sound goes out after 10 minutes of TV use


Rear projection hdtv, most likely damaged tubes. Don't repair this by your self get a tv repair man to do it before you injure your self.

Jun 24, 2008 | Pioneer SD-582HD5 58" Rear Projection...

1 Answer

Volume up then pic gone


Good Day;

The TV's front panel may be bad, manual buttons. TEMPT FIX; remove speaker, cloth covered, cover, disconnect cables. TV will work but only with remote.

Good Luck!

Jun 12, 2008 | Mitsubishi WD-52525 52" Rear Projection...

1 Answer

I have a philips Matchline tv (29pt6361/79r) the tv works fine except it automatically turns the volume down without any buttons on the remote or tv being pushed


well depends on how far it turns the volume down as to what the cause is and if the volume bar on screen display comes on when the vol. goes down. if it just goes down a little you probably have the "smart sound" setting turned on in the audio menu turn it off and see if prob. goes away. if the vol. bar comes on the screen whenever the vol. goes down the you most likely have a bad button on your front panel and it doesn't have to be the vol. down button. it you think it is the button it would need solder work to be changed most likely shop job.

Mar 08, 2008 | Projection Televisions

1 Answer

Volume lowers


replace digital board. A hardware update is available that might solve it.

Feb 12, 2008 | Zenith E44W46LCD 44" Rear Projection...

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

60792 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...