Question about NetGear WGR614 Wireless Router

1 Answer

VPN name or address to set up my palm zire 72

I do not know which name or address is. Where I can find it? Thanks.

Carlos Eduardo Llano Jaimes. callaja2000@yahoo.com

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 236 Answers

Http://www.routerlogin.net/

Posted on Aug 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Asus fonnepad does not conect automatically to wifi router


1. Launch a browser and access router settings by keying in http://192.168.1.1 on the address bar.
2. To set up the VPN server:
1) Click "VPN Server" on the Advanced Settings menu on the left panel.
2) On the "Enable PPTP Server" item, select "Enable".
3) Select type of Broadcast Support.
4) Select type of Force MPPE Encyrption.
5) Type a range of IP addresses for the VPN clients. The example on the screenshot below shows an IP address range of "192.168.10.11" to "192.168.10.20".
*The specified IP address range can be from 192.168.10.2 to 192.168.10.254. As a VPN server, the ASUS router can assign only a maximum number of ten IP addresses.
6) Input a username and password for VPN clients. A maximum of ten usernames and passwords can be added.

Aug 14, 2014 | Routers

2 Answers

On-Q Home 4 Port Router/Switch P/N 364772-01 1307791 REV.0


You need two things, the settings for the VPN to setup your computer to connect, and you need to set your router to allow VPN passthrough, look for settings like IPSEC, PPTP, etc. in your router's setup.

Usually you can access your router's setup through a web page, to access this, Click on start, then run, type in CMD and press OK.  When the command prompt window comes up, type in IPCONFIG.  Note the Default Gateway IP address that is listed.

Open a browser like Internet Explorer, and type in that IP address into the address bar like this:  http://192.168.1.1

Then you will probably need a user name and password to get in, and while you are in there, check for things like port forwarding, applications, and VPN to find the settings that you are looking for.

If you are unable to locate this information yourself, I am available for remote assistance, all that is required is that you email me a request for assistance and request a PIN.  I am usually available during the evening hours (Central Time).

Oct 24, 2007 | ON-Q Home 8-PORT Internet Firewall Route...

1 Answer

Frequent VPN connection drop on my wifi


If you can't connect via the Internet to your workplace network from home (or another location), check the items in this list:

  • Make sure that you typed the virtual private network (VPN) server name exactly as provided by your network administrator.

  • You must have an active Internet connection for a VPN connection to work.

  • If your modem is external, make sure that the modem power is turned on.

  • Contact your network administrator to make sure that you have the appropriate connection and domain permissions on the remote access server.

  • This could be a certificate problem. For assistance, contact your network administrator.

  • A VPN connection won't work with an active Winsock proxy client. Contact your network administrator to make sure the Winsock proxy client is not enabled.

  • If you know the IP address (for example: 131.107.10.25) of a website, type that address in the address bar of your web browser and press Enter. If this works, there is probably a Domain Name System (DNS) resolution problem. For assistance, contact your network administrator.

  • If you have special software that's required or installed by your workplace, it could be part of the problem. For assistance, contact your network administrator.

  • If you know the IP address (for example: 131.107.10.25) of your VPN server, type that address for the VPN connection, and then press Enter. If this works, there is probably a DNS resolution problem. For assistance, contact your network administrator.

  • There could be a problem with the server you're trying to connect to. For assistance, contact your network administrator.

If you try to connect with a VPN connection and you see a message that says "The local computer does not support encryption" and has the error code 741, it's possible that the encryption that your computer uses doesn't match the encryption used by the VPN server. To change the encryption settings so that your computer uses the recommended setting of 3DES, follow these steps:

  1. Open Connect to a Network by clicking the network icon (eff2d36c-9e0d-4d1a-9859-3af14fa4ccfc_73.jpg or da12251d-1e9a-4032-afae-009876c6c5a3_80.jpg) in the notification area.

  2. Right-click the VPN connection, and then click Properties.

  3. Click the Security tab.

  4. Under Data encryption, select Maximum strength encryption (disconnect if server declines), and then click OK.

  5. Open Connect to a Network by clicking the network icon (eff2d36c-9e0d-4d1a-9859-3af14fa4ccfc_73.jpg or da12251d-1e9a-4032-afae-009876c6c5a3_80.jpg) in the notification area.

  6. Click the VPN connection, and then click Connect to try connecting again.

Apr 21, 2013 | Belkin Surf N300 Wireless N Router

1 Answer

How configurate this router? I lost the CD with configuration. Please ask me. Mabey in Polish language?:)


Connect your router to computer with ethernet cable then you can access it with following default link.
http://192.168.0.1
or
http://192.168.1.1
If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it.
Then it ask for user name and password.
Type user as "admin" and password as "admin" or "password" or blank.
Then you can see configuration page of router.
Click on WAN settings and set those settings as your internet service provider settings.
Enable DHCP if you want to get ip from router.
Click on wireless settings enable wireless then enable WEP Security then add WEP code .It is your password to connect wi fi.Then save settings and restart router.
Then you can connect your wi fi network with that code.
When you connect vpn router to wireless router set in wi fi lan property as your vpn network range set vpn router ip as gateway ip of wireless router.Then save settings and restart it.
Let me know if you need further assistance.
Thanks for using FixYa.

May 20, 2010 | NetGear WGR614 Wireless Router

1 Answer

I have a netgear rangemax won824 v2 I can connect to it fine, but I cannot connect to a works server after vpn connection successful. can someone help


VPN Passthrough Configuration

1. Please assign an IP address to your computer using the IP Address Reservation.

a. Please open any web browser like Internet Explorer or Netscape Navigator.
b. Connect to the router by typing http://routerlogin.com/basicsetting.htm or http://192.168.1.1 in the address field and click Enter or Return key.
c. A window will prompt for a user name and password. The default username is "admin" and the default password is "password".

Note: If it does not take password as the password, you might have changed it when you have run the NETGEAR Setup CD so please try other passwords. If you cannot remember the password, you need to reset the router and run the Setup CD to reconfigure it.

d. On the setup page, please click LAN IP Setup under Advanced tab.
e. Click Add under Address Reservation then you will be brought up to a new window.
f. On the Address Reservation window, please select the radio button of the computer you wish to add.
g. If the computer you want is not on the list; click the Refresh button to update the table.
h. If the computer is still not on the Address Reservation Table; please enter the IP Address, MAC Address, and Device Name of the computer you wish to add.
i. Please click on the Add button when finished.

2. On the Set Up page of the router, select on Port Forwarding/Port Triggering under Advanced tab.
3. Click Add Custom Service and type VPN on the Service Name box.
4. Set the Service Type to TCP/UDP and input the VPN port numbers under the Start and End Port field.
5. Type in the last digit of the IP address of your computer. Then, click the Apply button.

Example: The IP address of the computer trying to establish the VPN connection is 192.168.1.2.

Service Name Start Port End Port Server IP address
VPN1 47 47 192.168.1.2
VPN2 50 51 192.168.1.2
VPN3 500 500 192.168.1.2
VPN4 1723 1723 192.168.1.2

Jun 07, 2009 | NetGear RangeMax WPN824 Router

1 Answer

I am trying to set up PPTP connection to the internet on my WRV54G router (behind a cable modem). The set up calls for a fixed IP address, mask and gateway address, but my ISP is not providing those - only...


most cable companies are dhcp configured. so you would leave the wan config as default. the only thing i would do is mask the computer mac address. this should give you the access you need.

Mar 09, 2009 | Linksys Wireless-G VPN Broadband Router...

1 Answer

I cannot access internet when connected to VPN.


1. Please assign an IP address to your computer using the IP Address Reservation.

a. Please open any web browser like Internet Explorer or Netscape Navigator.
b. Connect to the router by typing http://routerlogin.com/basicsetting.htm or http://192.168.1.1 in the address field and click Enter or Return key.
c. A window will prompt for a user name and password. The default username is "admin" and the default password is "password".

Note: If it does not take password as the password, you might have changed it when you have run the NETGEAR Setup CD so please try other passwords. If you cannot remember the password, you need to reset the router and run the Setup CD to reconfigure it.

d. On the setup page, please click LAN IP Setup under Advanced tab.
e. Click Add under Address Reservation then you will be brought up to a new window.
f. On the Address Reservation window, please select the radio button of the computer you wish to add.
g. If the computer you want is not on the list; click the Refresh button to update the table.
h. If the computer is still not on the Address Reservation Table; please enter the IP Address, MAC Address, and Device Name of the computer you wish to add.
i. Please click on the Add button when finished.

2. On the Set Up page of the router, select on Port Forwarding/Port Triggering under Advanced tab.
3. Click Add Custom Service and type VPN on the Service Name box.
4. Set the Service Type to TCP/UDP and input the VPN port numbers under the Start and End Port field.
5. Type in the last digit of the IP address of your computer. Then, click the Apply button.

Example: The IP address of the computer trying to establish the VPN connection is 192.168.1.2.

Service Name Start Port End Port Server IP address
VPN1 47 47 192.168.1.2
VPN2 50 51 192.168.1.2
VPN3 500 500 192.168.1.2
VPN4 1723 1723 192.168.1.2

Dec 01, 2008 | NetGear WGR614 Router

1 Answer

Gateway to gateway tunneling vpn


can you provide more information:
- WAN IP addresses of both routers
- LAN IP of both routers.
- name of ISP for both


i can provide a solution if i will know these info

Nov 16, 2007 | Linksys RV042 VPN Router

1 Answer

VPN


This example will demonstrate how to create a Virtual private Network (VPN) between two remote locations through the Internet. The VPN policy will use 3DES IPSec to securely send/receive encrypted data over the Internet. When the VPN tunnel is enabled, the two offices will virtually appear to be on the same local network. This example will consist of two DI-804V VPN Routers with a simple setup. The two remote offices in this example will be known as Office A and Office B. Both VPN Routers must already be set up and able to access each other. This is only an example, your setup will vary using the WAN IP address provided by your ISP. Please note the differences in the IP addresses for each office. We will begin by configuring the DI-804V at Office A. Start by going into VPN Settings under the Basic Setup menu. Step 1. In the Connection Name field, type in OfficeA. Click ADD. Step 2. A properties screen will appear for the new connection you have made. Fill in the appropriate information for Office A: Connection Name: OfficeA Local IPSEC Identifier: Local Remote IPSEC Identifier: Remote Remote IP Network: 192.168.1.0 Remote IP Netmask: 255.255.255.0 Remote Gateway IP: 192.170.0.2 Network Interface: WAN ETHERNET Secure Association: IKE Perfect Forward Secure: Enabled PreShared Key: 123456 Key Life: 28800 IKE Life Time: 3600 Step 3 Click SAVE. There should now be a VPN policy created for Office A. Now you will want to Save & Restart the DI-804V. Note: 123456 is an example of a preshared key, please fill in any secret preshared key you desire. Keep in mind that both sites require the same preshared key. Office A setup is now complete, we will now configure Office B with the other DI-804V, Follow the same steps previously with Ofice A to create a VPN policy. Step 1 Please change the appropriate information. Connection Name: OfficeB Local IPSEC Identifier: Local Remote IPSEC Identifier: Remote Remote IP Network: 192.168.0.0 Remote IP Netmask: 255.255.255.0 Remote Gateway IP: 192.170.0.1 Network Interface: WAN ETHERNET Secure Association: IKE Perfect Forward Secure: Enabled PreShared Key: 123456 Key Life: 28800 IKE Life Time: 3600 Step 2 Click SAVE. There should now be a VPN policy created for Office B. Now you will want to Save & Restart the DI-804V. After the VPN policies have been created for the two Offices, the two remote locations should authenticate and connect. To view the status of the VPN connection, go to the Device Status menu. On the bottom-left side of the menu, click on the VPN Status icon. A VPN Status pop-up screen will appear showing VPN connection status. If a VPN tunnel is active, the State should indicate Q-Estab. Go to a DOS prompt and ping the internal IP address of the remote network.

Feb 16, 2006 | D-Link DI 804V (DI-804V) Router

1 Answer

Nortel Contivity VPN client?


Nortel Contivity will work with the your D-Link router, however its functionality depends on the authentication type (AH will not work), NAT compatibilty mode, and disabling keep alives on the server. Contact your Network Administrator to find out how your VPN is configured. Step 1 Verify that you are using the latest version of firmware on your router. Step 2 Login to the Web Management for your router by entering its IP address (192.168.0.1) in your web browser. The default username is admin, and the password is blank. Step 3 Click the Advanced Tab to access the Virtual Server Settings. There is a list of pre-defined Virtual Server Rules towards the bottom of the page. Find the IPSec Rule. Click the pen and paper icon to edit its settings. Enable the rule, enter the IP address of the computer attempting to connect to the VPN in the Private IP field, then Apply the changes. Step 4 Create a new Virtual Server entry. Name the Virtual Server, "NortelVPN". Enter the IP address of the computer attempting to connect to the VPN in the Private IP field. For the Protocol Type, select Both. Enter 9550 for both the Public and Private Ports. Set the Schedule to always, then Apply the settings. Step 5 Access the Tools Page, then click the Misc button. Disable IPSec Pass-through, then click Apply. If the VPN Server is properly configured to work with clients behind NAT routers you should be able to connect to the VPN.

Feb 16, 2006 | D-Link Express EtherNetwork DI-604 Router

Not finding what you are looking for?
NetGear WGR614 Wireless Router Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top NetGear Routers Experts

Barry37

Level 1 Expert

31 Answers

MrNutsy

Level 1 Expert

36 Answers

Phillip Whisenant
Phillip Whisenant

Level 2 Expert

120 Answers

Are you a NetGear Router Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...