Question about Computers & Internet

1 Answer

I have a Symbol MC9063-S scanner and I am stuck at the alignment screen for a day now.

Posted by on

  • 2 more comments 
  • ericmendez8 Apr 09, 2011

    Yes numerous times but really to no avail.

  • ericmendez8 Apr 09, 2011

    It does happen in my sort of work, scanner being dropped sometimes, is there a self fix for mis-aligned scanner bar?

  • ericmendez8 Apr 10, 2011

    Will give that a go and let you know what happens, thanks. Stay online please

  • ericmendez8 Apr 10, 2011

    No good, did not work as well



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert that hasĀ over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 207 Answers

Have u tryed reseting the unit turning it off and on somtimes its the software problem..

Posted on Apr 09, 2011

  • 3 more comments 
  • anthony Apr 09, 2011

    has the unit been bumped in anyway your scanner bar might be unalined and needs fixing how to tell is it way over where its supposed to be or slightly out.

  • anthony Apr 09, 2011

    yes you need tools first find out what one you need phillips or a star screwdriver i make my own somtimes take your time get to the realinment bar witch is sealed unit wear rubber gloves u dont want oily fingers on the inside glass push the bar way over back in its pasition try to remember when it last worked witch side put it back together and see if that works.

  • anthony Apr 10, 2011

    what kind of scanner you have...

  • anthony Apr 10, 2011

    ok i need rest iv been on this site all day i do alot of fixes in all sorts of electronics when stumped i step back, check you tube somtimes techs like too show there work on scanners and printers there try there u be there awhile but somtimes its time for a new one...

  • anthony Apr 10, 2011

    sorry i couldn't help im new too doing this on the web im more a person to person guy..



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

The align screen for MC9090 is not calibrate. Already calibrate but still the touch screen is not proper.

Hi you need a replacement digitizer. The unit may have been dropped hence the reason it is now faulty. please contact for repair. 00441179064587

Aug 05, 2011 | Symbol MC9090-G Barcode Scanner

1 Answer

Yhe screen keeps rolloing very quickly can get it to stop

SOUNDS LIKE YOU NEED A REPLACEMNT SCREEN AND DIGITIZER. The digitizer may be corrupt and stuck in a single place on the screen. Contact a repair centrew.

May 04, 2011 | Zebra Symbol Technologies MC909X-G Series...

1 Answer

How to get gun back to config screen

If you stuck with some application on the device. You can restart it by holding the power button for 10seconds

Apr 17, 2010 | Zebra Symbol Technologies MC909X-G Series...

1 Answer

Stuck on align screen...

You must tap the exact center of the '+' symbol with the stylus pen 5 times: at the middle and at each corner of the screen (it will move itself as you go tapping). If you miss one of them, even slightly, the process will be restarted.

Hope you are able to align your screen and move on.

Cheers! Carlos

Apr 16, 2010 | T-Mobile Wing Smartphone

3 Answers

MC9060-G stuck in IPL (initial program loader mode.

Windows Active Sync will not recognise a scanner in IPL mode. You need to install the Symbol Device Configuration Package that is applicable to your scanner/cradle. Once installed and configured you can use SDCP to restore the Hex files needed for basic operation. All the files and loader software can be found at
Good Luck

Oct 21, 2008 | Symbol MC9060-G

1 Answer

Align Screen

It will need a new screen. This is a common fault on this type of terminal and since the touch pannel is incorporater on the screen assembly, that is the only solution.

You could always try a software update from IPL mode, however is not very likely that it will resolve the calibration issue.

Jul 23, 2008 | Symbol PPT 8800 Wireless Barcode Scanner

3 Answers


I used the manual keys to get to the alignment screen...
But the unit would not hold the settings.

Feb 13, 2008 | Symbol MC70

1 Answer

Connection Issues

can you give more info,
1>can you see the network? (scan)
2>can you connect to the network?
3>do you get a valid IP?
4>can you ping the server?

if you can not connect to the network(2) but see the network(1) via scan the problem is in your wireless profile, delete the profile and resetup, check that the region settings in the profile match that of the unit.

i will need more info about you network, ie wep/wpa? ch? authentication type? and so on

Oct 19, 2006 | Symbol MC9063-K (mc9063kkehbeea4ww)...

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18424 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

David Payne
David Payne

Level 3 Expert

14162 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides