Question about Washing Machines

1 Answer

While running the washer in mid cycle, quit working. Ld error code. the tub has water. emptied clothes. Unplugged, burst if water, then stops

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 415 Answers

Ld is = Long drain, something has plugged the pump and must be remove to work properly, or the pump has failed 95% of the time its a sock or something like that.

Posted on Apr 09, 2011

  • fixrguy Apr 09, 2011

    Ld is = Long drain, something has plugged the pump and must be remove to work properly, or the pump has failed 95% of the time its a sock or something like that.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

LG washer WM2501HWA quit mid cycle and had an OE error message. The drain filter was checked and was clear. I drained out all the water through the drain hose. For a time, the drum would not spin. When...


i believe if the water outlet is still good,,,,,u will have to loose out the pump from its cup , mayce something hooked its propeller inside the i cup or replace the water pump

Jan 25, 2015 | LG Washing Machines

1 Answer

Brovos Maytag Showing a Error F1 is this an easy fix?


The code is caused by a water sensor. You can temporarily just dump about a half gallon of water into the tub before adding the clothes, and then have another half gallon for mid cycle. This stops the code from popping up. Try the half gallon thing and you will see.

I would try to run a few loads of towels with just water (no detergent or anything) to try and flush out any excess detergent residue you may have. I don't know if you are able to set your own water level on this machine, but if you are, I would just run an empty load or two.

Hope this helps...

Jul 23, 2011 | Maytag Bravos MTW6600T Top Load Washer

1 Answer

When running wash cycle, the washer stops during initial cycle when water is going into tub. The "Ld" error code comes up on the panel and sometimes it is accompanied by a humming sound. Can not start...


LD is long Drain.

You'll need to crawl underneath and disconnect the hoses to check the traps for obstructions.
Have a pan handy to catch the water.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Sep 10, 2010 | Whirlpool Calypso GVW9959K Top Load Washer

1 Answer

Whirlpool Calipso model clothes washer shows a LD and doesnt run


The OB indicates and out of balance condition has been detected by the motor control.
One thing about the OB error is that the lid must be opened to clear the error and allow the washer to advance to the next part of the cycle. If the lid is not opened to adjust the clothes then the OB error will happen again.

If the OB error was cleared and the OB occurs with an empty load then the motor control has failed.

The drain pump must work. The image below shows how to run a diagnostic test to check the drain pump. Follow the instructions in the image below and check the drain pump operation. If the pump runs and the water does not drain then the sump is clogged. If the pump hums but does not run then the pump needs to be replaced.

http://media.fotki.com/1_p,wkktswgwqtqrbwfxgtqsskgwtqkq,vi/gftrgbbtfxfffgqskfk/1/1303472/5961857/image48348img-or.jpg

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Jul 05, 2010 | Whirlpool Calypso GVW9959K Top Load Washer

1 Answer

Had a LD error and successfully cleared clog in waste water tank. Turned it on and pump worked perfectly to pump out water. Started a new cycle to test everything and things went wrong. First, the tub...


If the water keeps filling with the unit unplugged you have a bad water valve(or low house pressure)
If the unit does stop filling when unplugged you have a plugged pressure hose to the pressure switch or a bad pressure switch. To access you peel back the front emblem to remove a screw in the center. This allows you to raise the top to check the pressure hose. You can also find the end of the hose at the control panel to blow through it, should be clear when tub is empty of water. A hole in the pressure hose would also cause flooding. This hose connects from the bottom of the outer tub to the pressure switch in the console to control the water level in the tub. Unit will not turn on drain pump if it does not sense water in the tub......
good luck......

Apr 06, 2010 | Whirlpool Calypso GVW9959K Top Load Washer

5 Answers

Kenmore Calypso washer Ld code?


I just had the same problem. I borrowed my neighbors wet vac. The hose of the wet vac fit right over the end of the drain hose and I sucked out all the remaining water. My hope was that if the hose was clogged that it would clear it out. It seems that it worked. I put the drain hose back in the drain and turned on the extended spin cycle. It was working, so I put the water logged clothes back in the washer on the extended spin cycle and it took the water out. I am now in the process of washing another load to see if it really fixed the problem. I hope this helps.

Jan 18, 2009 | Whirlpool Calypso GVW9959K Top Load Washer

5 Answers

Whirlpool Cabrio WTW6600SW1: Won't drain


The washer drew half a tub of water on the "Bulky items" cycle, and stopped. All the lights on the cycle dial light up and flash, the machine beeps and the me error message in the "estimated time remaining" field is "Ld". I've tried to shut the machine down and change the cycle to "drain and spin" but it will not agitate, won't drain or spin.

Sep 05, 2008 | Whirlpool Cabrio WTW6600SBT Top Load...

1 Answer

Error code LD


I had this problem also. Ld means that it is taking too long for the tub to drain, usually something is clogged. Try taking a shop vac and sucking out the drain hose that goes into the wall drain. This should at least get you where the tub will finish the cycle you have going. I tried this and it worked for about 2 loads then "Ld" again. Finally removed the drain pump from the washer and let it empty completely. So far this has worked.

Jun 10, 2008 | Kenmore Oasis HE 27062 Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1461 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Brad Brown

Level 3 Expert

15667 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...