Question about EnGenius EAP-3660 802.11b/g Wireless Access Point

1 Answer

Im trying to connect an EnGenius 3660 access point to my laptop. It connects and finds the network, but i have no internet. The EnGenius is wired to my pc. Don't think i am doing this right. My Droid picked it up right away and has internet cabability. windows 7 home premium on laptop windows 7 ultimate on PC Toshiba Satellite A665 Realtek RTL8188CE Wireless LAN

Posted by on

  • tjmdds Apr 09, 2011

    Still no internet access from the EAP-3660 Access Point when connecting the wireless to the laptop.

    Checked the laptop with another wireless connection and that worked, so it doesn't appear to be on the laptop end.

    EAP-3660 connects wirelessly to the laptop and have network access, just no internet.

    Have tried with WEP, have tried with WPA, no security/open without any luck.

    The EnGenius is wired to my PC and the ip for this is set at 192.168.1.21 with a sub of 255.255.255.0

    When i changed the TCP/IPv4 to automatic IP, i can no longer access the web device portal when doing this.

  • tjmdds Apr 09, 2011

    Good to go. Actually just ran network cable for EAP-3660 to a switch and now have network and internet for laptop.

    Thanks

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,530 Answers

Welcome to Fixya
Check the wireless adapter properties of your computer. Under the TCP/IP the IP address and DNS address should set to automatic detection. Please see picture below.
im trying to connect an - elix0411_28.jpg

Once you are connected try to ping a website ans see if you are getting reply from a website e.ge yahoo.com. click start then type CMD from the start search box then press enter. Type in ping yahoo.com from the command prompt. Please see picture below.
elix0411_29.jpg

Please reply this email for any feedback.
Thank you for using Fixya!

Posted on Apr 09, 2011

  • Jose Cada
    Jose Cada Apr 09, 2011

    Try to set the IP automatically assigned from the IPv4. Then go to the command prompt then type in ipconfig. You should be getting the same IP address when you do this. You mentioned that you are not getting issue with your EnGenius 3660 since your droid can connect to that gadget. Do you have other computer there? Try to check their settings. Especially with the TCP/IP. Other computer should fall with the same IP network which is 192.168.1.x.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WiFi disconnects


the problem with your AP , change it

Mar 14, 2014 | EnGenius EAP-3660 802.11b/g Wireless...

1 Answer

Can't log in Engenius EAP-3660 .after rest factory settings.why? can you help me pls


You don't seem to understand what an Access Point is.

an AP is used to extend your wireless range and will connect to your routericon1.png to provide network and internet access. An AP by itself cannot connect to the ISP since it does not use a WAN port

a router is an AP that will allow you to connect to your ISP for internet connection. A router can be configured to work as an AP but a AP cannot function as a router.

Read the manual. When you reset the AP the IP of the AP device became 192.168.1.1
That means you need to set the IP address of your computer to 192.168.1.x where x is anything from 253-2 and the subnet mask to 255.255.255.0

Feb 19, 2014 | EnGenius Computers & Internet

1 Answer

No internet


I had exactly the same problem with my EnGenius ENS202EXT. I was trying to set up an Access Point, hard wired to a FAST1704N V1.0 Router/Modem from Windstream communications.

I spent 2 days trying/altering as many different combination settings as possible, on the Engenius. It turned out in the end that I had alter an unnecessary setting in the Fast1704 modem/router. After I reset the modem to factory settings everything worked beautifully. I have great coverage and higher speeds than I ever had before.

Note: in addition to the fact that internet would not pass through to the Access Point I was trying to set up, neither would the FAST1704N V1. show up on the internal network. I could not find or communicate to the FAST1704N V1. through my own network until I reset my modem/router. After resetting the modem and getting internet through the AP, I went back an readjusted the critical settings in the modem. Everything working great.

Oct 10, 2013 | EnGenius ENH202 Wireless Outdoor 800mW...

1 Answer

Problem loging into the web page of EnGenius EAP-3660 Access Point


I thought the default IP was 192.168.0.1. That is where mine went when I pressed the reset button.

Jan 10, 2013 | EnGenius EAP-3660 802.11b/g Wireless...

1 Answer

WDS Setup


In a WDS network, all the access points need to be in WDS mode, and one of them needs to be wired directly to a routed internet connection.
Here is a very good detailed tutorial on how WDS works and how to configure and troubleshoot your own WDS network:
How To: Setting up WDS Bridging / Repeating

Jun 03, 2010 | EnGenius EOC-2610 802.11b/g Wireless...

1 Answer

Engenius eap-3660 access points channels chashing.


This is a massive and expensive network, which appears to require a full signal and configuration audit. It's quite possible that many of your problems are stemming from the APs you have already deployed being situated in suboptimal and conflicting locations, which is an issue with three-dimensional wireless networks.
I really don't see your problems being debugged by anyone short of an experienced on-site wireless network technician. I'm saying this as a person who tuns a one-man company serving two rural communities with wireless internet service.
Sorry.

May 07, 2010 | EnGenius EAP-3660 802.11b/g Wireless...

1 Answer

I set up the Engenius EAP as a repeater and can connect to it with my lpatop and Iphone. When I try to connect another laptop I have excelletnt connectivity reception, but Internet Explorer cannot display...


Signal is only one part of the complete connectivity problem. Your lack of connectivity is almost certainly due to some other component, such as your second laptop having an incompatible static IP address specified, or no DNS servers specified.
First, ensure your PC is configured for a dynamic IP address. Once you have acquired good signal and connected, check to see that you have received a dynamic IP address. If that works, open IE and type in the numeric IP address if your EPA repeater. If you get a response, the problem is not your wireless connection or local IP address. Now type in the IP address 74.125.19.103 . If you get a response, your problem is that you have no DNS servers specified.

Feb 28, 2010 | EnGenius EAP-3660 802.11b/g Wireless...

Not finding what you are looking for?
EnGenius EAP-3660 802.11b/g Wireless Access Point Logo

Related Topics:

379 people viewed this question

Ask a Question

Usually answered in minutes!

Top EnGenius Computers & Internet Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Michael Vincent Cruz

Level 3 Expert

868 Answers

Karen Gibson

Level 1 Expert

16 Answers

Are you an EnGenius Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...