Question about Hampton Bay 24002 Ceiling Fan

1 Answer

Need a Dealer near to zip 33160 - Hampton Bay 24002 Ceiling Fan

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 876 Answers

ID there a Home Depot nearby?

Posted on Aug 07, 2008

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I find a new remote for my Kenmore ceiling fan, the remote model number is R520T

notify kenmore [sears] for a parts dealer near you or if can order one also online companies

Aug 12, 2016 | Fans



My dog knocked off my vornado which then broke a blade off my favorite fan. I was going to use epoxy to try to get the blade to stick back on. This would not work. The fan spins to fast to use glue. I sat and thought about it for awhile and came up with a solution rather then spending 39.99. I used epoxy to get the blade where it should be and let it dry..... then took a hot nail and poked a hole through each blade close to the center of the shaft.... and then took a zip tie and connected each zip tie to each other forming a ring around the shaft. This works very good and if you need to balance out the fan just place a small zip tie on the center and clip off close to the lock. Now you can use the LOCK as a balance for the fan. GOOD LUCK

on Aug 28, 2008 | Vornado Circulating Fan

1 Answer

Where is closest deealer/ My zip 18034

7245 MARY DRIVE #27 Center Valley PA 18034

Jun 27, 2014 | Emerson CF2454 Ceiling Fan

2 Answers

Fan only wobbles on high....recently 'bumped'

Check all your screws especially the set screw at top of fan that goes into rod. Blades could be warped from the water. Ball of fan not set in bracket correctly. When your buying a fan, look for blade pitch.13 degree or better is best. You shouldn't have to use the fan on high unless it's a low-end fan with a low blade pitch. It's costing you more money to run the fan on high. Sorry to get so preachy, I'm a fan dealer .

Jun 19, 2013 | Fans

1 Answer

How to wire Dayton capacitor start 6K321BA 1HP

Maybe you can solve this problem by contacting Dayton or an electrical products dealer who handles the product

Jan 02, 2013 | Dayton Permanent Split Capacitor Motor Fan

1 Answer


No, you could destroy the motor. Simply take the grill off by cutting the plastic ties, use a screwdriver for leverage and pry apart. You'll put it back together the same way, sans zip-ties.

Nov 17, 2012 | Patton Electric U2-20 Box Fan

1 Answer

I need a blade bracket for a brushed nickel finish

You will only be able to obtain a replacement from either a Minka Dealer that happens to have one in stock, or from Minka directly.

As the Minka is very restrictive with their distribution, it would be best to contact them directly with a request for a replacement part/

Here is the web site for Minka and you can see your model, the Acero, listed on the ceiling fan section. If you look at the bottom of the page, you'll find a "contact us" link that you can use to request information about getting your replacement part. There is also a "dealer contact" link at the top of the page, so you can locate a nearby dealer that might be able to order the part for you, etc.

Hopefully you'll be able to get the replacement blade bracket, as your fan model is still in production, and as such, should have spare parts available.

I hope you'll find this Very Helpful and best regards!

Oct 04, 2009 | Minka Acero Brushed Nickel Ceiling Fan

2 Answers

Hampton bay Model 23758 replacement bulbs

go to any near home center (if there one). they should have the size bulb you need.
Home depot is authorized dealer form Hampton.

Oct 12, 2008 | Hampton Bay 24002 Ceiling Fan

1 Answer

Hampton Bay Carriage House II

I went ahead and hooked up the wires, and then zip stripped the wireless receiver to the side of the motor mount. Works fine and fits inside the canopy (motor cover).

May 30, 2008 | Hampton Bay 13087 70450 Carousel II...

4 Answers

How do you clean Patton Floor fan?

The grill is in two halves with the back half attached to the motor. The front with the round patton insignia removes easily by applying leverage with a screwdriver. There are eight spots (at least on mine) where it clips. Be sure to remove any disposable plastic fastener holding the two halves together. Its pretty easy.

Sep 12, 2006 | Patton Electric U2-20 Box Fan

Not finding what you are looking for?
Hampton Bay 24002 Ceiling Fan Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hampton Bay Fans Experts


Level 3 Expert

3287 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Are you a Hampton Bay Fan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides