Question about Dishwashers

1 Answer

I have the following part , http://www.buyspares.co.uk/door-lock-mechanism/product.pl?pid=1232905&query=MDI673001800135 for my kenwood dishwasher yet there is a spring attached to it , and i do not know where this goes ?

Posted by on

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,323 Answers

Hi

Please check this video:


Hope this helps...please post back for further assistance.

Daniel

Posted on Apr 08, 2011

  • Daniel Scott
    Daniel Scott Apr 08, 2011

    Yup that was an example on how its done...you can also check this video:


×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

ADP 4730


The problem is with either the spring or the solenoid that operates the detergent compartment door. It should be released at the right time by the controller during wash cycle. You have to check the spring and see if it stuck. But if solenoid is faulty then whole detergent dispenser has to be replaced. You could switch to detergent tablet which you drop in the cutlery basket and it works fine. A brand like Finish works well and keeps dishwasher clean.
Alternatively you can purchase a replace detergent dispenser from

http://www.buyspares.co.uk/whirlpool/adp4730-851150429849/dispenser/product.pl?pid=18330&path=463858:496324,47872:463870&refine=dispenser&model_ref=641830

Also watch the video on how to replace.

Apr 23, 2014 | Whirlpool Dishwashers

1 Answer

Caple dishwasher stops & beeps continually before finishing 60 degree cycle


Thanks for clarifying the model number. See the user manual at this site. You can download and save it for future.

http://www.caple.co.uk/downloads/manuals/dishwashers/di414-di440_dishwasher-manual.pdf

But I don't think this will help you in the problem. It is very likely that the thermal limiter relay is faulty. It is meant to protect the dishwasher from over heating. It must be cutting before 60deg.

You can see the circuit diagram of a related Capel model on this page.

http://www.caple.co.uk/downloads/manuals/dishwashers/di604.pdf
You can see the part looks like this

http://www.4caple.co.uk/ntc-probe-feeler/product.pl?pid=357313&query=Di414

Apr 12, 2014 | Caple DI60715 Dishwasher

1 Answer

Kenwood Microwave oven CJ/AL28 The turntable is not rotating. Have tried moving the piece underneath glass and it is locked in position. How can I resolve this issue? Many thanks S. Heal


Hi and welcome to FixYa, I am Kelly.
POWER OFF / UN-plugged
To gain acces to the motor the outer chassis must be removed. 4 side scews and 6 rear screas.. then life the rear of the outer cabinet 10 degrees and slide it aft to unlock the front tabs. Then remove the cover. Before you do anything; take a good screwdriver held by the handle and ground the HV capacitor 3 times across the 2 terminals to prevent a horrible shock.

The turntable motor will accept input (0utlet) power when disconnected and a test cord connected to the turntable motor PN TYJ5807A. Some of these are 24 Volt motors... make sure you look on the motor to determine the voltage. You can test the motor for resitance on R x 1,000 scale. I should read resistance to the 2 terminals only and NOT to the case. If it reads from either terminal to the case the motor has failed. The windings in these motors are MUCH thinner than human hair. http://www.buyspares.co.uk/search.pl?query=TYJ508A7
or
http://www.4kenwood.co.uk/cgi-bin/product.pl?PID=944115

Take a good look at the motor drive post and make sure it matches yours. I could not find an exact parts break down for the CJ/AL28 but most turn table motors are common in a brand.

Thanks for choosing FixYa.
Kelly

Nov 28, 2010 | Emerson Microwave Ovens

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Owen Barnes

Level 3 Expert

867 Answers

Brad Brown

Level 3 Expert

15557 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...