Hi. My Whirlpool AWO 5761 washing machine has an F09 error message and the door is locked with washing inside it. I have pressed the reset button and tried to start other programs, but the message reappears.

The F11 fault code indicates a serial communication error between the Machine Control board and the Motor Control board. This can be caused by several different problems.

A failed Machine Control board could be failing to provide the Motor Control board with proper voltage. If this is causing the F11 code, then the Machine Control board would need to be replaced.

The Machine Control board could also be failing to supply proper voltage to the door lock assembly. The Machine Control board would need to be replaced for this failure as well.

Voltage flows from the Machine Control board to the Door Lock Assembly. The Door Lock then energizes and closes the Door Lock MAIN Switch. Voltage flows out of the Door Lock Main Switch to the Motor Control board. So if you have power into the Door Lock Assembly but not out of the Main Door Lock Switch, it will give you an F11. If so, you will need to replace the Door Lock Assembly.

You could have a bad Motor Control board that is causing this failure. A bad wiring connection between the Motor Control board and the Machine Control board could also cause this fault code. A bad wiring connection between the Motor Control board and the drive motor is also a possible failure. A failed drive motor could also cause the F11.

With so many possible causes for this failure, I recommend calling a service technician to diagnose and repair the problem in your washer. If you are able to unplug the washer and check the wiring connections, you may be able to find a loose wire harness connection that is causing the problem. Much of the diagnosis for the potential problems noted above requires live voltage checks. I do not recommend conducting these types of checks yourself. Unless you want to take a chance and replace the Machine Control board and the Door Lock Assembly,

Hi Lisa. I'm not familiar with the particular machine but I suspect that if you look just inside the machine near the door catch you will see a small button/lever that operates a switch. (look up microswitches on net). Switch either needs adjusting or replacing. You could try holding the switch closed with your finger or something to see if the machine is going to work - if it does look like working (filling?) the switch just needs adjustment.

sounds like low water pressure, check the supply hose is not kinked

F09 Overflow condition If the Overflow contact on the pressure switch is Closed for more than 60 seconds an Overflow condition will occur. In an Overflow condition, the Door will remain locked, and the Drain Pump will run constantly, even if PAUSE/CANCEL is pressed twice and the Display is cleared. Unplug the unit to service.

Potential Causes

• Check the drain hose and make sure it is not plugged or kinked
• Check Wire Harness connections to the Drain Pump, Pressure Switch, and Central Control Unit (CCU)
• Check / Clean Drain Pump Filter of foreign objects
• Check for Drain Pump Failure
• Check the Inlet Valve for proper shut off
• Check the Pressure switch for proper operation

Replace failed component.

Read more: http://www.appliancepartspros.com/repair-help/whirlpool-fault-codes.html#Whirlpool Duet Front Loading Automatic Washer Fault Codes#ixzz2e96NFcLn
http://www.appliancepartspros.com

Hi.

F-22 is door lock error. The door lock was already defective and now has failed completely. You need to replace the door lock.

Here the error explained in detail:

F22
DOOR LOCK ERROR
Theme Door Lock message is prompted when the door cannot be locked. The CCU (central control unit) will try to lock the door six times before displaying the F 22 error code.

Possible Causes:

The door lock mechanism is broken or removed from door.
Door switch/lock unit failure.

Repair Procedure:

1. Unplug washer or disconnect power.
2. Check door switch/lock unit.
3. Check the wire harness connections to the door switch/lock, and the central control unit.

Regards.

Ginko

F09 Error = Overflow Condition

If the Overflow contact on the pressure switch is Closed for more than 60 seconds

an Overflow condition will occur. In an Overflow condition, the Door will remain

locked, and the Drain Pump will run constantly, even if PAUSE/CANCEL is pressed

twice and the Display is cleared. Unplug the unit to service.

Potential Causes

• Check the drain hose and make sure it is not plugged or kinked

• Check Wire Harness connections to the Drain Pump, Pressure Switch, and

Central Control Unit (CCU)

• Check/ Clean Drain Pump Filter of foreign objects

• Check for Drain Pump Failure

• Check the Inlet Valve for proper shut off

• Check the Pressure switch for proper operation

Hi,

Error F09 means Overflow Condition

If the Overflow contact on the pressure switch is Closed for more than 60 seconds and Overflow condition will occur. In an Overflow condition, the Door will remain locked, and the Drain Pump will run constantly, even if PAUSE/CANCEL is pressed twice and the Display is cleared. Unplug the unit to service.


Thank You

You most probably have a faulty water inlet valve...Not an uncommon problem..They can sound ok, but when you check the detergent drawer there will only be a trickle..Replace the inlet valve...Good luck...Nomess

need a manual for washing mashine Whirlpool AWO 10561

This is what F09 means

Condition
Overflow Condition
If the Overflow contact on the pressure switch is Closed for more than 60 seconds and Overflow condition will occur. In an Overflow condition, the Door will remain locked, and the Drain Pump will run constantly, even if PAUSE/CANCEL is pressed twice and the Display is cleared. Unplug the unit to service.



Check and repair

• Check the drain hose and make sure it is not plugged or inked.
• Check Wire Harness connectors to the Drain Pump, Pressure Switch, and Central Control Unit (CCU)
• Check/Clean Drain Pump Filter of foreign objects
• Check for Drain Pump Failure
• Check the Inlet Valve for proper shut off
• Check the Pressure switch for proper operation