Question about Kenmore 43142 Front Load Washer

Open Question

Kenmore HE2 110.4751 my washer stopped and displays (F-28) error it wont open the door ans does nothing, I have tried unplugging the machine but anything makes it open the door

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Need to change door from left hand to right hand open on kenmore HE2

I am looking for the same answer on the washer. You can definitly change the dryer. The holes are on the other side under black tape.

Posted on Jun 26, 2008

Ad
  • 220 Answers

SOURCE: f21 code on kenmore he2 plus

Clean the filter in the pump behind the bottom panel,but remember it's full of water,If it's on a pedestal you can take the pump loose from the mounting pull it out a little and put a small pail or bucket under it before you open the trap.if it isn't on a pedestal it's a bit more challenging unless your in a basement with a floor drain. Open it very slowly and let the water drain a little at a time don't take it all the way out or you'll be in for a flood....good luck

Posted on Sep 03, 2009

  • 5 Answers

SOURCE: Kenmore HE2 front load washer. All cycle lights flashing plus spin and clothes clean lights on.

I'm sure this is probably too late, but hopefully it will help some else. I just had the same problem. First, unplug the power. Then take the lower front panel off and grabbed a bucket. Place the bucket under the large "plug" on your right. This is the drain. Slowly unscrew the drain plug, Hold your nose as it will probably smell. Allow the water and such to drain into the bucket. When you see the blob of wet lint drop into the bucket you will know why the machine refused to work. Make sure you clean the drain plug and screw it back in tightly. Put the lower panel back on and reconnect the power. I hope this resolves your issue.

Posted on Oct 10, 2009

blueextc3221
  • 15935 Answers

SOURCE: Kenmore HE2 Plus Washer won't unlock

This advice is for Kenmore Elite and Whirlpool Duet model front loading washers. If you experience a problem where the door becomes jammed and will not unlock or open, here's an easy way to gain access inside your washer WITHOUT calling the repairman.

1. Remove the lower panel under the door by loosening the three screws under the bottom edge on the front of the washer. HINT: If you prop up the front feet of the washer with some small blocks of wood, this will make access to the screws much easier.
2. With the screws removed, the lower panel should drop down then come off. If the panel sticks, a light tap on either side will knock it loose.
3. Reach your hand up inside the washer behind the front casing on the right-hand side. This is where the door latch assembly is located.
4. At the bottom of the door latch assembly is a small pull tab. This is the manual release for the door. Pull the tab straight down and the door will come open.

Sometimes these doors will not unlock for whatever reason. If there are no error codes being generated, this could have just been a momentary glitch. If you see "Fdl" or "Fdu" error codes, these are usually indications of a failed door latch assembly and will require replacement.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Posted on Sep 10, 2010

Macmarkus
  • 2605 Answers

SOURCE: Why does my Kenmore He2

Hello,

Welcome to FixYa.

The "F2" on your model of washer indicates the machine has detected a fault or obstruction in the drain process.


Chances are the pump itself is being obstructed by debris or some other foreign object as opposed to being faulty, although a faulty pump can`t be ruled out...yet.

Here`s how to check it and clean it...there is also a bellows at the bottom I`ll show you how to check

Posted on Oct 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error code f-28


F28 means your washer is locked and not unlocking. To unlock your washer take off the bottom access panel by removing the 3 bottom screws. Reach up near the latching assembly & attached to the door latch is a little plastic pull lever. Pull down on this lever and open the door. Unplug your washer for 60 seconds and plug your washer back in. If the error re-occurs you need to replace your door lock.
Click if helped.

Apr 30, 2013 | Kenmore HE2 Washing Machines

1 Answer

My Kenmore Elite Oasis HE model number: 110.27072603 washing machine shows LID error code. It wont work at all.... went half way through cycle... help.


Greetings,
this washer has a lid switch problem...or possible main board failure, but lid does concentrate on the lid safety switch. If you remember when you open the lid it stops..well, its a safety feature and prevents tub from spinning with lid open...this one is more difficult to service if your not use to working on washers...try unplugging machine and leaving off for awhile...does the door lock? check switch for lid fault

Nov 25, 2010 | Kenmore Oasis HE 27082 Top Load Washer

1 Answer

Kenmore washer, model c45092


in all cycle with seven min left washer, m-c45092 stop and door open no spin cycle. pete.

Apr 19, 2010 | Kenmore 45081 Front Load Washer / Dryer

1 Answer

Have a kenmore elite 3 washer...stopped with 8 mins left in cycle...try to restart but getting F DL code...cannot open washer door


A Door Lock Error occurs if the door cannot be locked. It will try to lock it six times before displaying the error code.

Possible Causes / Procedure

• Door lock mechanism is broken or removed from door.
• Door switch/lock unit failure.
1. Unplug washer or disconnect power.
2. Check door switch/lock unit.
3. Check the wire harness connections to the door switch/lock unit and Central Control Unit (CCU).

Replace the door lock mech if the wiring is ok

Oct 11, 2009 | Kenmore Washing Machines

1 Answer

F-28 code


F28 means your washer is locked and not unlocking. To unlock your washer take the bottom access panel off by removing the 3 bottom screws.
Reach up near the latching assembly & Attached to the door latch is a little plastic pull lever. Pull down on this lever and open the door. Unplug your washer for 60 seconds and plug your washer back in. If the error re-occurs you need to replace your door lock.

Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Jun 28, 2009 | Kenmore HE2 Plus Front Load Washer

1 Answer

Kenmore F-28 error - door locked can't get in


Unplug the machine.
Wait 15 seconds.
Plug machine back in.
Press and hold the Power button until the lights come on.
Press and hold Start.
When you hear a click, press Stop.
Open door.

You still have an F-28 issue but you can at least get your clothes now.

Hope this helps.

Jun 09, 2009 | Kenmore HE2 Plus Front Load Washer

1 Answer

Washer wont engage


The door may not have been fully closed. stop/clear cancel the cycle. ensure door is fully closed and attempt to resart cycle.

F/dL Door Lock Error
A Door Lock Error occurs if the door cannot be unlocked. It will try to lock it 6 times before displaying the error.
  • Door Lock Mechanism broken or removed from the Door
  • Check Door Lock/Switch Assembly
  • Check the wire harness connections to the Door Lock/Switch Assembly and Central Control Unit (CCU)
  • Door Lock/Switch Assembly Failure

Feb 08, 2009 | Kenmore HE2 Plus Front Load Washer

1 Answer

Kenmore H3T washer


The following link explains the "FH" error in detail:

http://www.fixya.com/support/r615354-fh_error_code_whirlpool_duet_kenmore

You may still have a water inlet problem if the washer is not filling and the taps are turned on.

If the door is locked and you cannot get the door open, you can use this link on how to access the manual release:

http://www.fixya.com/support/r622155-kenmore_elite_whirlpool_duet_door_jammed

These problems may be attributed to a momentary glitch. Unplug the washer for 30 minutes and use the manual release to unlock the door. In many cases the problem(s) will clear. If the problems still persist, go to my profile and use the "Ask Me" feature for a quicker response to any questions you may have. I hope this helps you.

Jun 15, 2008 | Kenmore 3.8 cu. ft. HE3t Front Load Washer

1 Answer

Please help , tell me why door is locked, on h 2 kenmore washer,


THANK YOU,
still nothing,

red doorlock light on, wont do anything,

I have to unplug so it will shut off,

when I plug in and hit start, red light stays on again,

Mar 28, 2008 | Kenmore 4292x Front Load Washer

Not finding what you are looking for?
Kenmore 43142 Front Load Washer Logo

Related Topics:

178 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Sal DeAngelo

Level 3 Expert

2286 Answers

fordexpert

Level 3 Expert

5537 Answers

 Brian Main
Brian Main

Level 3 Expert

464 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...