Question about DSC Pc Classic Led615 Keypad For Pc1500/1550 Led 615 Nw

Open Question

I have DSC Led 615 alarm system how do I turn my chime off so when you open the door it does not chime/

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 17 Answers

SOURCE: my DSC security system is reading

First of all go to your security box.Now you will have to find where all the sensors conect to the panell.These area's on the board are called zones such as zone 1 zone 2 and so forth.Chech and make sure no wires have came loose from the screw termanils also make sure their is no corrision (good contacts are key).If this doesent work you will need a magnet find out which zone you are having trouble with such as front door back door window ect.Now their are two different sensers one is a flush mounted senser this will look like a little box on the frame of what ever it is securing.The other one will be a inset one this will be harder to find.It will be inside the frame of what ever it is securing.In any case you wil need to run the magnet over this device and see if the panel will reset.If this hapens then you know that their is something wrong with the orig. magnet.(When you shut the door or window the orig. magnet will align with the senser).Some times the distance between the senser and the magnet will effect the senser.If the senser is a flush mounted senser then their will be some wires you can acess to see if they are making contact.

((((( I DO NOT RECOMENT THIS ONE. IF YOU TRY THIS ONE YOU WILL NOT BE PROTECTING THIS ZONE AND SOMEONE CAN NOW BREAK IN )))))The next thing to try is to simply look on the panel door and read where it says which resistor it needs and where it goes on the panel in relationship to the correct zone buy the resistor and install it in the panel.

((((( I DO NOT RECOMEND THIS ONE. IF YOU TRY THIS ONE YOU WILL NOT BE PROTECTING THIS ZONE AND SOMEONE CAN NOW BREAK IN)))))The next thing to try is the zone bypass.The instructions on how to do this should be on the back of the key pad door.

The next thing to try is to look in the senser to see if it has a battery.Some sensers have a battery and they need to be replaced from time to time.Now I have been asuming that this is a senser on a door or a window but their are other sensors that are optional on this panel as well.Check all wires on these batterys and make sure all outer housings are securly on the sensors.

If none of this works then you probably either have something wrong with the wireing or the panel its self is faulty.If so contact a security technician.

Posted on Jul 30, 2009

  • 78 Answers

SOURCE: have ADT 3000 series alarm system - would like to set it to max

adt sw3000 panel does not support max button on key pad. best solution would be to have ADT tech reprogram Zones so windows are perimeter zones(instant when armed away or stay) and motions interior follower (instant when no perimeter zone was triggered first). doors stay exit/entry.

Posted on Mar 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

15 year old micromark intruder alarm need to switch off


Not really enough info to give you an answer, but I can generalise...

You say Knocked alarm box with ladder alarm started"
If the fault is there permanently from when this happened there's a good chance that you have disturbed the tamper spring/switch on the cover of the alarm unit. when the front of the panel is removed you should be able to see the Sping/switch which is automatically depressed by this front panel, you may find the spring has fallen off the switch or gone out of alignment, refitting / realigning it should remove the tamper fault once the lid has been refitted properly. As for "bleeps when doors, windows opened"
This sounds like the "Chime" feature has been switched on and without the manual I cannot tell you for sure how to switch it off.
Chime is a feature which "Chimes" when a door is opened (Not often used on windows), if this started when the ladder fell on the panel it is most likely just a single key press to switch it off, Once the tamper fault is sorted you should be easily able to find the correct key press to turn the chime feature off.
Sorry for being a bit general but I don't have that particular manual. Hope the info helps you :o)

Mar 20, 2017 | Home Security

1 Answer

How can I turn off chimes?


Read your manual; I do not provide any info regarding alarm system disarming questions etc...

Jun 06, 2015 | DSC Rf5501-433 Powerseries Wireless...

1 Answer

How do you disable the door chime?


many drivers have dash lights to inform them that a door is open yet they still drive around and then complain about a knock some where in the back
I would check all the door sensors for adjustment and leave the alarm alone as , as annoying as it might be , it might let you know when a child has opened a door without your knowledge and save a life.

Mar 25, 2015 | 2009 Toyota Camry XLE V6

1 Answer

Dsc pc 1555


Is this a Laptop problem or a home security question? If home security, is the door a wired or wireless zone? A Chime on the door, is that on the control panel or a local chime at the door?
Are you absolutely sure zone 5 is that door? Is your bypass zone activated? You should be able to hold arm to arm it anyway.

Nov 16, 2013 | Computers & Internet

2 Answers

Location of tail gate alarm on 2004 Chrysler Pacifica


you may have a bad switch which is located on the latch asm

Sep 03, 2012 | 2004 Chrysler Pacifica

2 Answers

Does the bcm control the alarm in a 2006 monte Carlo? I can't seem to get the alarm to go off. I've also noticed that I have no chime and turn signal sounds. I just recently purchased this car and...


The no chime and turn signal has nothing to do with the alarm. You have a issue with power supply to turn flasher and door chime. The alarm consist of The door ajar switch,body control module,front door lock switch,power door lock switch. You need to check your fuse for turn signal and the door chime

Feb 22, 2012 | 2006 Chevrolet Monte Carlo

1 Answer

My led light for my alarm stays on and the alarm dont work anymore but the button still locks?unlocks/and starts


Your system is in valet. To take the system out of valet with remote: open any door, press lock, unlock, lock. Now check the LED; it should be off. Close the door and arm the system to check.
OR
Turn the key on then off. Within ten seconds press and release the valet switch. The LED should be off now. Close the door and arm the system. The alarm should chirp to confirm that it is armed.

Nov 26, 2010 | Remote Start System

1 Answer

Alarm not beeping when doors are open. led on door goes red when door is opened and alarm box has red and green lights when alarm is actived but not chimes or alarm when doors are opened


When a zone has both red and green lights on, it means that it is in delay mode. That means when the sensor is triggered, the system will wait for a predefined time interval (30 seconds) for user to reset the trigger. During this time interval, the system will not beep or alarm. But after that, if user does not reset the trigger, system will go off.

User can reset the trigger from keypad or by remote.

Sep 05, 2010 | Skylink Group Skylink Security System Kit

1 Answer

Will the alarm go off or not?


Hi, alarms can be programmed to chime/not chime etc. Simple way is actually test it just to be sure. Set the alarm and try the door. If it doesnt work, then the door sensor could be faulty OR that chanel could have been programmed to be bypassed. Will require the user man for programming. Best of luck

Jul 22, 2009 | Kitchen Appliances - Others

1 Answer

1997 venture keyless remote programming


SYSTEM OPERATION

System warning lamp located on top of the instrument panel
Press UNLOCK button once , turns on interior lamps and deactivates alarm (if fitted)
Press UNLOCK button twice w/in 5 seconds unlocks all doors, turns on interior lamp and deactivates alarm (if fitted)
To activate alarm system (if fitted):
Switch ignition OFF
Open driver's door
Press Lock button on remote
Close Driver door
warning lamp will flash when system is activated
Press remote power sliding door button will open sliding door (if fitted) only if unlocked first
Pressing remote panic button:
*Sounds horn intermittently
*Flashes exterior lamps
*Turns on interior lamps
**Pressing panic for the second time OR switching ignition ON deactivates alarm.


PROGRAMMING
Remobe key from ignition switch
Remove the "BCM PRGRM" fuse, from the fuse box
Close all doors
Turn ignition switch to the ACC position
With in 1 SECOND , turn the ignition switch to OFF then back to 'ACC'
(really, with in one second)
Open and close the driver's door. A chime will sound, indicating programming mode activated
Press and HOLD LOCK and UNLOCK SIMULTANEOUSLY untill a chime sounds 2 times ( about 15 seconds)
Repeat this exact procedure for all remotes to be programmed
Remove key from ignition
Refit 'BCM PRGRM' fuse.

4 REMOTES MAXIMUM CAN BE PROGRAMMED

Aug 24, 2008 | 2000 Chevrolet Venture

Not finding what you are looking for?
DSC Pc Classic Led615 Keypad For Pc1500/1550 Led 615 Nw Logo

Related Topics:

396 people viewed this question

Ask a Question

Usually answered in minutes!

Top DSC Home Security Experts

Steve

Level 3 Expert

3287 Answers

yobo007
yobo007

Level 3 Expert

507 Answers

don1956

Level 1 Expert

8 Answers

Are you a DSC Home Security Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...