Question about Panasonic Workio DP-190 Multifunction Laser Printer

2 Answers

We have replaced our drum and the alram light still blinks and we still have a message to replace drum.

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 41 Answers

Check that the drum is a genuinely new drum, and not a recycled one.
If it is a new drum, make sure it's inserted fully into the machine and that all contacts (the shiny copper bits) are clean and not covered with toner or anything else.
Also make sure that after any fiddling with the Drum that you fully restart the machine and put it through it's test cycle.
If the problem persists, the drum sensor may have gone bad and will need to be fixed by an authorized repairman.

Posted on Apr 07, 2011

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 73 Answers

Turn off and unplug the printer, remove the drum and re-seat it firmly. plug the printer back in and turn it on.

Posted on Apr 07, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, we have the hp color laserjet 2840 series and we are getting a supply error (10.1004). The picture shows that there is a problem with our imaging drum. We bought a brand new imagind drum and it is...


Reseat the toner cartridge. Turn the printer off, and then back on again. You may want to try a new cartridge, but if that does not eliminate the error, call your HP support line. If the imaging-drum light is still blinking but the Attention light is not on, you must replace the imaging drum before the printer can continue printing. The imaging-drum light might be blinking by itself or at the same time another light is on or blinking. If another light is also on or blinking, turn the imaging-drum light off in the simulator and turn the other light on or blinking to isolate the condition. The printer has determined that it cannot read or write to the e-label on the imaging drum.Reseat the imaging drum, and then power cycle the printer. If this does not work, replace the imaging drum. If the imaging drum light is still blinking but the Attention light is not on, turn the printer off, and then back on. If the problem persists, replace the imaging drum E-label reader. The imaging-drum light might be blinking by itself or at the same time another light is on or blinking. If another light is also on or blinking, turn the imaging-drum light off in the simulator and turn the other light on or blinking to isolate the condition.

If Hope that this helps,, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response. Thanks,Joe


Feb 04, 2011 | Office Equipment & Supplies

1 Answer

We have a Brother 5240. We inserted a new drum and toner and the drum light still blinks. Can you advise what the problem is. Thank you


Before you replace the drum you have to clear the error message. To do that you have to Make sure that the printer is turned on and the Drum LED is blinking. Press the front cover release button and then open the front cover. Press and hold down Go for about 4 seconds until all the LEDs light up. Once all four LEDs are lit, release Go.
Here's a link to the Brother website on how to replace the drum with images and instructions.

Dec 01, 2010 | Brother HL-5240 Laser Printer

1 Answer

Replaced drum but light continues to blink


To reset the photoconductor drum counter, press and hold the Cancel button on the printer until all lights flash in sequence. You can clear the Replace photoconductor message only when the imaging drum has been replaced. For more information on how to replace the drum, see the User's Guide.:

http://support.dell.com/support/edocs/systems/prn1720/


Click on this link or copy and paste the complete link into your browser.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.

Thanks, Joe

Nov 11, 2010 | Dell 1720dn Laser Printer

1 Answer

The red drum light is blinking and it will not make copies


HI drum is reach for end of life thats why drum light is blinking you shuld have to replace the drum or just reset the drum counter to run your machine for another life .
thanks

May 11, 2010 | Sharp AL 1631 Copier

2 Answers

Drum light blinking


The light blinking means it's almost used up, when it comes on solid it will stop printing. If your prints still look good you can open the front door and hold the go button til all lights flash, and it will think it's a new drum. You can replace then when print quality gets bad.

Jan 06, 2010 | Brother HL-2040 Laser Printer

1 Answer

Drum light flashing in spite of new drum unit and new toner cartridge


common problem.
  • The Drum LED blinks if the drum unit is near the end of its life. Use the drum unit until you have a print quality problem, then replace the drum unit with a new one.



  • The Drum LED continues to blink if the drum counter was not reset when you replaced the drum. To reset the drum follow the instructions below:
  1. Open the front cover of the printer.
  1. Press and hold down Go button for about 4 seconds until al the LEDs light up. Once all 4 LEDs are lit, release the Go button.
  1. Close the front cover.
Caution
    Reset the drum counter only when you replaced the drum unit with a new one.

Dec 30, 2009 | Brother HL-2040 Laser Printer

2 Answers

Drum light blinks


1. The Drum LED blinks if the drum unit is near the end of its life. Use the drum unit until
you have a print quality problem, then replace the drum unit with a new one.
2. The Drum LED continues to blink if the drum counter was not reset when you replaced
the drum.
To reset the drum follow the instructions below:
a. Open the front cover of the printer.
b. Press and hold down the white button for about 4 seconds until all the LEDs light up. Once all 4 LEDs are lit, release the
button.
c. Close

Dec 10, 2009 | Brother HL-2040 Laser Printer

1 Answer

Error light and Drum light are blinking. Do I


Blinking says to replace drum soon, when it's on solid, it's time for a new drum...

Aug 04, 2009 | Brother HL 2140 Laser Printer

2 Answers

Orange light is flashing and printer is not printing. It is not the crescent , not the triangle, but the one abve the triangle and below the colored catridge rotation button.


Imaging drum is empty or missing (Error 40204) Light pattern c00187081.jpg Description The imaging drum is empty or missing. The imaging drum light is blinking, and then printer stops printing. An error 40204 is written to the event log. The printer cannot detect the imaging drum correctly. Action
  1. Reinsert or replace the imaging drum.
  2. If the imaging drum light is still blinking but the Attention light is not on, turn the printer off, and then back on.
  3. Repeat Steps 1 and 2 with a new imaging drum.
  4. If the problem continues, contact HP Customer Care at http://www.hp.com/support/clj2550 or see the flyer that came in the printer box for other contact information.
Imaging drum e-label reader is faulty (Error 10004) Light pattern c00187081.jpg Description The imaging drum light is blinking, and then printer stops printing. An error 10004 is written to the event log. The imaging drum e-label reader is faulty and the printer cannot detect the imaging drum correctly. Action
  1. Reinsert or replace the imaging drum.
  2. If the imaging drum light is still blinking but the Attention light is not on, turn the printer off, and then back on.
  3. Repeat Steps 1 and 2 with a new imaging drum.
  4. If the problem continues, contact HP Customer Care at http://www.hp.com/support/clj2550 or see the flyer that came in the printer box for other contact information.

Apr 27, 2009 | HP Color Laser 2550N Printer

2 Answers

Alram light


Did you replace the Black ink cartridge or the Color cartridge, or did you replace both?

Facing the front of the Canon Pixma MX310, did you install the Black ink cartridge to the left side, and the Color cartridge to the right side?

Do Not reverse how the ink cartridges go. Do Not install a Black ink cartridge, in the Color cartridge holder.

If the Alarm light came on, check to see if you have an error message in the LCD. (Not trying to insult your intelligence. The LCD is the little rectangular Liquid Crystal Display on your Pixma MX310 Operation Panel, to the left of the numeric buttons)

Do you have the Pixma MX310 On-screen manual?
Start>Hover on All Programs>Canon>Pixma MX310>On-screen manual

Click on the Troubleshooting heading.
If you have an error message code, click on the heading ->
An Error Message is Displayed on the LCD.

Also suggest you click on the heading -> Problems Sending Faxes.

See if the information provided has a solution to your problem.

Apr 22, 2009 | Canon PIXMA MX310 All-In-One Printer

Not finding what you are looking for?
Panasonic Workio DP-190 Multifunction Laser Printer Logo

290 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Office Equipment & Supplies Experts

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6161 Answers

Mitch S
Mitch S

Level 1 Expert

25 Answers

Are you a Panasonic Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...