Question about Samsung CLX 3160fn All-In-One Printer

1 Answer

The printer was powere on and displays "Warming up

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 111 Answers

Open the front cover and empty the waist toner then try again.

Posted on Apr 10, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

HP Photosmart C6180 Ink System Failure


<br /> Hi,<br /> <br /> <br /> Please perform the following steps and let me know the message that will be displayed on the printer.<br /> Press and hold the "*" key. <br /> Press the "#" key and release both keys. <br /> Display should say "Enter Special Key Combo" <br /> Press and release in sequence the "1", "2" and "3" buttons.<br /> Press and release the right arrow button until the display says "System Configuration Menu".<br /> Press and release the "OK" button.<br /> Display should say "Hardware failure status". If not there already, Arrow Key over to "Hardware failure status",<br /> Press and release the "OK" button.<br /> Display should say "Hardware failure status: Clear. Press OK to clear".<br /> Press and release the "OK" Button. Message changes to "Hardware failure status Press Cancel to continue".<br /> Press and release the "CANCEL" button as many times as necessary, so that, either the "Welcome to Photosmart Express" screen appears, or, the "Ink System Failure" screen appears. PLEASE DO NOT TRY TO PRINT AT THIS STAGE.<br /> Using the Power Button, turn the unit OFF and unplug the power cable from back of the printer and wall outlet.<br /> Wait 30 seconds for the power to get discharged and then plug the power cable into the wall outlet first and then into the back of the printer<br /> Turn the unit on. The printer may display message "USE POWER BUTTON TO SHUTDOWN THE PRINTER" followed by "PRESS OK TO CONTINUE". Press OK. The Printer will start the "ONE TIME INK INITIALIZATION PROCESS". Allow this process to complete and do not interrupt. Once the initialization process is complete, the printer will print out a Diagnostic Page.<br /> <br /> If I could be of further assistance, let me know. <br /> Thanks,<br /> <br /> LETMEFIXIT

on Feb 04, 2011 | HP Photosmart C6180 All-In-One InkJet...

1 Answer

Samsugn Ml3310nd Laser Printer says warming up pls wait, and not initiallized just displayed warming up pls wait, ready, warming up pls wait.......... again and again


Dear
The problem mostly with fusser assy. as it is not getting proper temp. This may be due to the opened thermostat mounted on fusser and can be reset with dropping the detached thermostat on the floor.
Check the thermistor,
The SMPS which supply the heater supply may gets faulty(rare case), The main PBA may faulty (very rare).

thanks.

Feb 24, 2015 | Samsung Ml-3310nd Networked Mono Laser...

1 Answer

Hi, Im getting a costant "wat warming up" never


please format the hard drive by holding down the 0+8 buttons while switching on the machine when in test mode key in 690 press the start button make sure the number 2 is displayed when finished switch off and wait awhile then switch on if the machine still gives the error replace the hard drive and do the firmware good luck

Apr 01, 2011 | Toshiba e-STUDIO 352 Black and White...

2 Answers

When Copying or printing the paper does not feed


open the front cover pull out the cartridge and you see paper feed roller it is rubber. Clean paper feed roller with cloth and water or alcohol.

Jan 24, 2011 | Samsung SCX 4521F All-In-One Laser Printer

1 Answer

When I try to print a copy, display says "warming


A well documented problem. Try following the suggestions posted here

Dec 03, 2010 | HP PSC 750 All-In-One InkJet Printer

1 Answer

My Phaser 7700 Printer does not come to a ?Ready? state


This might be a bad main Image Processor (650-4307-00) board. We can isolate it by printing an internal test print.

You can power up the unit in diags (hold "back" & "info" buttons while powering up) Go to "Built in Test Prints" and try to print the "Grid 1 Dot Pattern"

If you print, then it's proven...

If not, then you will get an error that will allow further troubleshooting.

-Whit

May 10, 2009 | Xerox Phaser 7750DN Laser Printer

1 Answer

"Warming up Please wait" error


Suspect the toner heating element (fuser) may be malfunctioning. Dell may be able to walk you through a "hard reset" that involves opening the front door, turning on an off the printer with certain buttons held down, etc.

Jan 14, 2008 | Dell 1600n All-In-One Laser Printer

Not finding what you are looking for?
Samsung CLX 3160fn All-In-One Printer Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Office Equipment & Supplies Experts

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2017 Answers

HEMANT GROVER

Level 2 Expert

167 Answers

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

Are you a Samsung Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...