Question about Goodman GMS80903BNA Heater

1 Answer

I have a goodman furnace mod. gms80903bna the glow bar comes on but goes out before the main gas come though just replaced the board?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 40 Answers

Adjust the gas pressure on the gas valve or replace the gas valve

Posted on Apr 12, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Goodman furnace, model GMS80903BNA, is not working. I removed the back panels and checked the pressure switch. That seems to be working fine. The exhaust inducer spins up, the igniter starts to glow,...


That blinking 3 times is indicating a pressure switch problem. Try checking for water or a blockage in any of the hoses going to the pressure switch or condensate drain. Check the air intake and exhaust pipe for any blockage including any saggs that may hold water. Make sure condensate drain or pump is working. If you get a glow from the igniter, there may be a blockage in the gas valve or piping.

Jan 23, 2011 | Goodman GMS80903BNA Heater

1 Answer

Main Fan won't turn off even with thermostat removed. Burner not


There is a chart with the wiring diagram and othere charts that will tell you what the 6 blinks are for. That should tell you what is wrong and what part you need. Sounds to me like the board has an issue or the gas valve is locked out.

Jan 10, 2009 | Goodman GDS81155CNA Open Flame Mid-Size...

1 Answer

Goodman GMP075-3 ignition problem


bad board,i have had several board failures on goodman

Dec 18, 2008 | Goodman GDS80904BNA Open Flame Heater

3 Answers

Goodman GMP075-3 ignition problem


Goodman gmp075-3 gas furnace and the flame cycles for 4 sec

Oct 01, 2008 | Goodman GDS80904BNA Open Flame Heater

1 Answer

Goodman GMP075-3 ignition problem


OK, if the furnace is not lighting for even a few seconds, you have either a bad gas valve, bad wire, bad control module or no gas. The pressure switch is not the issue. Check all wires to the gas valve and look for 24 volts across them when the ignitor glows and you hear the click. Then test for 24 volts to ground. It could be a bad ground wire.

Sep 28, 2008 | Goodman GMS90703BXA Heater

1 Answer

Lock out on a goodman furnace


I have attached a link to download your owners manual troubleshooting guide. There is suggestions to follow coorisponding with the error codes.
http://www.dnmech.com/lit/IO-242.pdf

Oct 30, 2007 | Heating & Cooling

Not finding what you are looking for?
Heating & Cooling Logo

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Goodman Heating & Cooling Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

paulcarew

Level 3 Expert

2517 Answers

Brandon Berry
Brandon Berry

Level 2 Expert

407 Answers

Are you a Goodman Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...