I am facing a problem with the Nortel IP phone 2002 blank screen every morning, after pressing the key pad then will regisister back.

1. Press Feature x x 8463 (x x TIME) you should have Password displayed on your telephone.

2. Enter 22742 (BASIC) or 23646 (ADMIN) you now should have Hour on your display.

3. Now press Change and enter the correct hours using the key pad

4. Press NEXT and you should have Minutes displayed on your telephone, now press CHANGE and enter the correct Minutes.

5. Press NEXT and you should have Year displayed on your telephone, now press CHANGE and enter the correct Year.

6. Press NEXT and you should have Month displayed on your telephone, now press CHANGE and enter the correct Month.

7. Press NEXT and you should have Day displayed on your telephone, now press CHANGE and enter the correct Day.

8. Now you will have ---End of List--- displayed on your screen, you can now press Rls or handset down button to come out of programming.

open you 1120E IP phone and you will see a small power back inside. replace that power pack and it should be ok

Programming is done on 7310, 7324 and 7316 type sets.Enter programming by pressing the feature key followed by **266344.When prompted to enter the password enter 266344.
The screen should say TERMINALS&SETS. The 4 top line/feature keys are now used for programming.
At the terminals&sets prompt, press the show key (top right arrow). The display should now ask for an extension number. Enter extension number you want to change the name on.
Press the show key (top right arrow)
The display should say LINE ACCESS
Press the next key (bottom right arrow) .
The display should say CAPABILITIES.
Press the next key (bottom right arrow) .
The display say Name.
press the Chng soft key.
use the dial pad to enter the name. advance using the arrow soft key to go to the next letter
ex. Bill = 2,2 -> 4,4,4 -> 5,5,5 -> 5,5,5
Press the next key (bottom right arrow) to enter the name.
Press the release key when finished

Use the Transfer feature to redirect a call to the appropriate person.
To use the Transfer feature to direct a call to a third party:
To return to the original call, if the transfer is incomplete:
1. Press the Transfer soft key. The other
party is on hold and a dial tone sounds.
The LCD indicator light flashes steadily.
2. Dial the DN to which the call is to be
transferred or use Personal Directory,
Redial List, or Callers List to select a
number to dial.
3. When that number rings or a person
answers, press the Transfer soft key to
connect the calling party.
If the person called is not available,
press the line (DN) key (next to the LCD
indicator) to reconnect to the original
call.

I have the same problem. But instead of waiting around for solutions, I went inside the module and took a look. It looked interesting, lets just say that. When I gave up and but the circuit board back, RIPPPPPPP!! The little ribbon cable for the screen ripped off the circuit board. I am now devastated for now there is nothing on the screen. You can opt to buy a new module from here http://toonieshop.com/index.php?main_page=product_info&cPath=2_6&products_id=30

Hi there,
Depending on which type of phone you have;if you have one with a display you will see "Trans" on most Nortel phones with displays.It's only the M3902 which has a button either wriiten "Transfer" or dotted like a boomerang.
Hope this will help

http://www.fix-1.com/us/en/repair-Aastra...

Documentation centre -> Aastra Vista 350

1. Reset the phone by disconnecting and re-connecting power.
2. When the Nortel logo appears, press each of the four soft keys in sequence.
3. If no other configuration changes are required, press OK repeatedly until the “PC
Port? 1-ON 0-0FF” option appears.
4. Press 1 to enable the PC Port or 0 to disable the PC Port.
5. Select OK to confirm the change.
6. Restart the IP Phone.
When the IP Phone is restarted, the firmware sets the PC Port status accordingly

1.put the document for sending on the place
2.dial number
3.if you sending to a direct fax press start or send
and all is ok

Here are the MMS settings you will need to setup and/or verify:


From the standby screen, press the Menu Key.

Scroll to "Settings," press Select.

Scroll to "WebAccess," press Select.

Scroll to "Web Sessions," press Select.

Scroll to "Cingular MMS" press Menu.

Scroll to "Edit," press Select.

Validate the following parameters:
Name: Cingular MMS
Homepage: http://mmsc.cingular.com
Service Type 1: HTTP
Gateway IP: 66.209.11.32
Port 1: 9201
Domain 1: leave blank
Service Type 2: WAP
Gateway IP 2: 0.0.0.0
Port 2: 0
Domain 2: leave blank
DNS 1: 0.0.0.0
DNS 2: 0.0.0.0
Time out: 5 minutes
CSD no 1: leave blank
Username: 1: leave blank
Password 1: leave blank
Speed (Bps) 9600
Line Type 1: ISDN
CSD no 2: leave blank
User Name 2: leave blank
Password 2 leave blank
Speed (Bps) 2: 9600
Line Type 2: ISDN
GPRS APN: wap.cingular
User Name: [email protected]
Password: CINGULAR1
Press Done.

Press Exit.

Press Back

Press Back.

Scroll to "Messaging," press Select.

Press the Menu key.

Scroll to "Inbox Setup," press Select.

Scroll to "MMS Message Setup," press Change.

Scroll to "Server Info," press Change.

Scroll to "MMS", press Menu key.

Scroll to and select "Edit".

Validate the following settings:
Service Name: MMS
Server Name: http://mmsc.cingular.com
Web Session Name: MMS