Question about Miller matic 140 Mig Weld Package W/As/Cart 907335011

1 Answer

Gas not coming to gun - Miller matic 140 Mig Weld Package W/As/Cart 907335011

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Make sure gas is comming out of your tank if so check for obstruction in hose . if clear, when you press the trigger you should hear an audible click which opens the gas valve make sure the valve is opening. if ok check your feed line for obstruction .

Posted on Apr 05, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking for the nearest repair shop for paslode nail gun in Northren Va


Have all the nails been cleared out of the tool where they were jammed? If not take the fuel cell out of the tool, and remove the battery before working on it. If still persists come back to this website for further help.

Sep 19, 2014 | Omega Paslode 901000 Impulse Cordless...

1 Answer

There is no light coming on with a battery connected


First what kind of gun? If Paslode- may need new gas cartridge. And is power light green (still paslode gun.) If other type of gun can't help. sorry.

Feb 17, 2013 | Air Tools & Compressors

1 Answer

I have a new im65a pasloade nail gun that has only fired a couple of hundred nails and after standing for about 16 months the gun does not seem to be firing the fan comes on the green light flash the


your gas has expired , look at bottom of canister check the date. buy new gas also make sure cap on gas canister is down all the way till it snapps new gas doesnt come with cap down all the way

Apr 24, 2012 | Senco Air Tools & Compressors

1 Answer

When i put thew gun to wood there isnt a noise and wont fire a nail.when i lift off the fan comes on. what could the problem be.the gun is clean and all orings are in good condition.tried the piston on...


ok, start with checking gas delivery ,then with total clean. If still malfunction, check the setting of lower probe(part 66). I've owned my guns for 11 years and do all my own servicing. Most if not nearly all problems are caused by dirty components...cheers

Jul 06, 2011 | RTO PasLode 900420 Impulse Framing Nailer

1 Answer

Gas always comes out of the handle when the bottle is turned on on my FP 130


Hi:

That's very strange...

1) make sure you have the right nozzle, this gun takes both inner shield (gasless) and gas nozzle. so check you have a gas nozzle on it, the gas nozzle has a space around the contact tip for gas flow.

2) Check the tip holder this one must be free of spatter.

3) check gun's physical integrity, if it is kinked of brittle, probably you need a new gun.

Good luck.

If this was useful to you, please vote.

Mar 03, 2011 | Firepower Welding Tools

1 Answer

My wire welder acts like there is no shielding gas, but there is and at the right regulated pressure


If you can feel the stream of gas coming out the gun, then could be that the gas it's contaminated. It happens. I sell gas for business.

Nov 23, 2010 | Hobart Welding Tools

1 Answer

Engine runs , not getting any water flow when trigger pressed.


Disconnect hoses.
Look for kink in water hose.
Check incoming water connection for filter washer
Replace filter washer
If you don't have a filter washer, put one in.
Hook up water, and turn on
Water should come out other side of pump.
Turn on machine.
Do you get pressured water out of pump.
If no pressure, then pump is suspect
Hook up washer hose without gun
Does pressure come out of washer hose
Finally, the gun trigger may be bad.

We had to buy guns now and then.
Search for pressure washer guns
Following link shows guns we used:
http://www.ultimatewasher.com/pressure-washer-trigger-guns.htm

Oct 25, 2010 | Karcher G2650HHR Gas Pressure Washer

2 Answers

Starts but won't stay running, i clean carburator and still have same problem, unit has been used very little, still look new, Thanks,


Have you checked your oil? You need pump oil half way up in reservoir. Open plug on top of pump and check oil. Pump takes SAE 20 or 30

Next, open oil plug below engine and check your oil level. It should come up 1/2 way on dip stick. Engine takes 10W30. Don't turn washer on its side or upside down to drain oil or oil will run into carburetor.

Is the water turned on? Are you holding gun trigger open while starting? Pump needs water flow. DO NOT tie gun trigger open with wire and then start engine. That gun will flip around and shoot a hole in your leg.

If the engine starts, then you have gas, spark and compression

If engine won't stay running, the exhaust port might be clogged, or the carburetor is not letting in enough gas, or gas is not flowing to carburetor.

Check the screen over exhaust port > is it dirty or clogged? Clean with WD-40 or break it out with a screwdriver.
Remove gas filter below gas tank >>> it has a hex bolt >> loosen bolt >> the gas should come flowing out >> put it back if gas comes out
Next remove rubber gas line feeding gas to carburetor >> gas should flow out this line too >> if flows then put it back.

What about your air filter? Take it off. See if engine fires and runs without air filter. Air filter may be clogged.

While air filter is out, you can see open port to carburetor. Spray some WD-40 into carburetor. Fire up the engine. It should spark real healthy on the WD-40. Keep spraying WD-40 into carburetor to see if you can keep engine going. Don't forget to keep gun trigger open so water is flowing and pressure is not building in pump.

If engine keeps going with WD-40 but dies without it, then your carburetor is very suspect. You might need a new one.

If engine will not keep going with WD-40, then the spark is very suspect.

Change spark plug. Try again. If it doesn't fire up after that, you need to take it to the shop for repair.

Oct 09, 2010 | Honda 2500 PSI Gas Pressure Washer

Not finding what you are looking for?
Miller matic 140 Mig Weld Package W/As/Cart 907335011 Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Miller Welding Tools Experts

John Trevino

Level 3 Expert

1383 Answers

wadingriver
wadingriver

Level 3 Expert

2069 Answers

Jose Velazquez
Jose Velazquez

Level 2 Expert

227 Answers

Are you a Miller Welding Tool Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...