Question about Behringer Xenyx 1204fx

2 Answers

Beringer Xenyx 1204fx emits a clicking sound... Sounds like a Geiger Counter for radiation in my headphones. I have used the same sound mixer in the same configurations for 3 weeks. Now I've had it running for a week and no problems till this morning. I've disconnected all inputs and outputs and still get the clicking in the headphone jack.

Posted by on

  • adambosen
    adambosen Apr 07, 2012

    I have the same problem, but it comes and goes. I'll leave the mixer on for an hour not doing anything, and when I come back to it the effects bus is a Geiger Counter. It seems like if I unplug everything and wait a while (~ an hour) it goes away. Very frustrating!

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Behringer Master
  • 5,603 Answers

This is likely a problem with the FX in the unit or the power to it. Does the FX display act correctly? Check that the headphone source "Main Mix" is the ONLY button down for the headphones. If not, make it so. If the clicking is still there, try the headphones in the aux send jacks... see if EITHER left or right can hear the clicking. Back in the phone jack, scan across the SOLO channel buttons down one at a time. Is there clicking? If not, the problem involves the mixing buss or further down the line. Make sure the SOLO buttons at the FX Aux sends are up.
What effect does the MODE button have in SOLO and in PFL? Is the SOLO LED off? Is the number in the FX window SOLIDLY on and not flashing?

Posted on Apr 05, 2011

Testimonial: "Couldn't Fix problem using solution. Could not reproduce problem. I don't know if it is still there or not. Very insightful. Very quick response."

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My 1204fx effects do not seem to make it to the output stage of the mains plus 7/8 clip light stays on

Posted on Aug 03, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I've a problem with the Beringer XENYX1204FX


i got the same one but with less channels, it is probably a problem with the transformer, or a connection problem on the source in put.

Sep 16, 2016 | Behringer Xenyx 1202 12-input 2-bus Mixer...

1 Answer

I am hooking up a Behringer xenyx 1002B Mic/Line Mixer to my Toshiba Satellite c885-S5194 laptop to broadcast online via meridix. I'm using Audio technica BPHS1 Headset Microphones with XLS plugs and 1/4...


IF your Laptop has a stereo LINE 1/8" INPUT jack, you can take the Stereo ( Left & Right ) LINE outputs on your mixer and feed into this jack on your PC. You will need a 1/4" dual plug for the mixer end to a single 1/8" stereo plug on the PC end. I suspect the problem you are having is either related to your PC only have a MIC input jack or you have something set wrong in your PC's sound config. file. More information is needed to properly solve the problem.

Oct 18, 2013 | Behringer Xenyx 1002fx Mixer 10 Input 2...

1 Answer

No effects output xenxy 1204fx


Likely needs the DSP board replaced. It is the small board held on by 2 screws(if I remember correctly) and is easily replaced. I think retail cost is about $30 and can be ordered directly from Behringer.

Aug 03, 2013 | Behringer Xenyx 1204fx

1 Answer

My behringer xenyx 802 premium 8-input mixer worked fine for 1 day but now it sounds watery and behringer support was no help at all


Sounds like it may have failed. Yes, it is likely that it needs to be returned. Another option is to unplug all inputs and outputs. Plug in ONE device into the board, and use the headphone jack on the board. Does it sound the same? Just basic troubleshooting may help.

Oct 02, 2012 | Behringer Xenyx 802 8-input 2-bus Mixer W/...

1 Answer

I have a Behringer 1204FX mixer. It has an intermittent fault whereby the power supply pulses on off on off etc etc. This can continue for two minutes or ten minutes quite randomly.


That is known as :squegging". It can be caused by any of several failures. One failure involves overload that trips the overload sensor. Another is a problem in the feedback loop of the regulator. I would first replace C13 on the power supply and maybe C10. When working on these supplies use an isolation transformer for personal safety. Note that it appears that C13 MAY have too high a voltage rating and if an electrolytic the dielectric can deform and electrical value reduce. There are many other components that could cause the problem.

Nov 16, 2011 | Behringer Xenyx 1204fx

1 Answer

Best way to connect 2 1204FX mixers together


Try running the tape out of the slave to the tape in of the master unit. This us haywire, but should work. Use a stereo RCA cable.

Aug 08, 2011 | Behringer Xenyx 1204fx

1 Answer

My beringer europowered 800w mixer blew a fuse ,replaced it ,has blown several more fuse's since,i used a lower 5 amp fuse did not last - 10 amp is standard > is it time to trash this unit?


I don't understand because the Xenyx 1002fx draws only 16 Watts so the fuse should be well less than 1 amp why would you put a 5 amp?

And your 800 Watt mixer???... There is something wrong with this model number as the 1002fx certainly is not 800 Watts. Please supply the correct model numbers so we can help you.

The unit is repairable I am sure.

Aug 21, 2010 | Behringer Xenyx 1002fx Mixer 10 Input 2...

1 Answer

Can't get any gain without feedback when using my new shure sm81 mic and the xenyx x1240usb fx mixer. keep the speaker way out in front of me. no montiors. using just a hair of reverb and compression. have...


This is a STUDIO mic and CANNOT be used in the presence of speakers that are driven from its output.

There is special hardware processors to cancel feedback but you do NOT want to go there !!!

This condenser mic is to be used in a studio where performers wear earphones and NO monitors are present.

You should use a Shure SM58 or other CLOSE talking cardoids if you have speakers in the area.

Jun 09, 2010 | Behringer Xenyx 1002fx Mixer 10 Input 2...

3 Answers

Iam trying to make my behringerXENYX 1204fx mixer, / connect


I have trouble my new behringer xenyx 1204FX VU led dead , like new VU it must play , how to repair this unit VU light

Mar 13, 2010 | Behringer Xenyx 1002fx Mixer 10 Input 2...

1 Answer

Do I need to connect the Xenyx 1202 to an amp?


If you are the only person listening, you can use headphones with the headphone jack. Otherwise you will have to use some sort of amplification and speakers,e.g. P.A., stereo etc. I'm using a Xenyx 1222 FX and am quite happy with it.

Mar 22, 2009 | Behringer Xenyx 1002fx Mixer 10 Input 2...

Not finding what you are looking for?
Behringer Xenyx 1204fx Logo

375 people viewed this question

Ask a Question

Usually answered in minutes!

Top Behringer Music Experts

Vito Vacirca Jr.

Level 2 Expert

140 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1066 Answers

Ben Armstrong

Level 2 Expert

334 Answers

Are you a Behringer Music Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...