Question about Yamaha EQ-70 Home Equalizer

1 Answer

Lightbulb????? How do u screw n a light bulb

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 120 Answers

Is this a "trick" ? I assume very carefully so the bulb won't break!

Posted on Apr 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No taillights but turn signal and break lights work.


These use a dual element bulb. It's 2 bulbs in one. The brighter element inside the bulb is used for the BRAKE light & turn signals. The second, dimmer element in the bulb is for tail lighting during night driving. Because they're on the whole time you drive at night they tend to wear & burn out sooner then the BRAKE light element. Assuming they're both the same age, they would burn out close to around the same time. Replace the bulbs. However, the tail lighting/running lights are also on separate wiring too. So check for damaged, rotted, or shorted wiring or bulb sockets, & also check the running lights fuse. If the fuse is blown, it's a good sign you have shorted/bare wiring, or damaged socket.

Apr 23, 2016 | Dodge 1997 Ram 1500

1 Answer

Why no brake lights?


Did you check the bulbs? ground?

Use a known good bulb and see what happens. If no light then power is definitely not reaching the bulb or the circuit is not complete.

You might need a schematic to track down the possible component responsible for the situation.

Sep 05, 2015 | 2007 Buick Terraza

1 Answer

I have a 99 s10. The right taillight and back up lights go out at random times during cold weather. The brake lights work fine. I think its a short but I'm not sure


Check the ground wire at the right taillight. This is usually what I find is the trouble spot. It should be grounded to the body from the light receptacle. Clean off rust from wire and body, it may be necessary to replace the ground wire and or drill new hole for ground screw.

Jan 17, 2015 | Metra 99-4544 1982-2002 Chevy S10 Pickup...

1 Answer

How do I reset abs and brake light on 1997 dodge ram 1500. Replaced speed sensor. Also unplugged Pulse control box under dash. Light is determined to stay on. Please help


Some cars/trucks run the ABS power through the brake light bulbs!
Does brake light and ABS light come on separately,key on,engine off?
Be sure that the parking brake switch is not bad.
The brake light should flicker/get brighter/dimmer when actuationg the parking brake.
Also,defeat the low fluid warning sensor.Defeat the pressure differentail switch.
I know some MFRs make both lights come on when either system fails.

Check for signal FROM the sensor at a wheel Use A/C voltage mode. I have spun the undriven hub with an electric drill to see A/C output.

Please note that the brakes will work OK but you not have ABS function.

See if you can get the brake warning light out,separately.

Nov 12, 2014 | Dodge 1997 Ram 1500

1 Answer

Brake lights don't work


Check light bulbs .check fuse under dash

Nov 19, 2012 | Chevrolet 1995 Chevrolet S10/s15/sonoma...

1 Answer

All lights on the 02 Escalade works except the dash, all fuses are good, all bulbs are good as well


your dimmer switch for dash lite control as well as dome lite may be bad double check your fuses with a test lite as sometimes a fuse will look good its not blown but the wire can break inside

Jul 07, 2012 | Equalizers & Crossovers

2 Answers

Headlights sometimes dont work


I had similar problems on headlight and I solved them installing relays on high beams. It worked well, if you don't know how to do it just ask.
Anyway, if the voltage is getting to the bulbs right (the relay should assure this (try to put a direct wire between the positive on the battery and the pin of the bulb, to see if things change: if so, the relay is bad or badly fitted)), if the bulbs are new, and the exterior lenses are in good shape, then it can only be the inner reflective surface. I heard people that removed the headlight form the car, filled it with water, some sand and whatever through the bulb hole, and, shacking the whole headlight, cleanig them, but I didn't ever do it personally.
Try the test of the wire between the battery and the bulb, if there's any change in brightness then the fault you're looking for is electrical, and can be restored with well installed relays.

home lights

Jun 07, 2012 | Dodge 1997 Ram 1500

2 Answers

My pioneer DJM 600 lost master output the other day, it was playing and the master out just died. the lights were still lighting up but no sound came out. I was using the RCA outs not the xlr and haven't...


hi there i have a djm 500 but i have the same screw on the back its like an ATT for master output and if i turn it all the way down i have no sound but if i turn it up it gets alot louder lol

Jun 11, 2010 | Pioneer DJM-600 Silver Professional DJ...

2 Answers

Yamaha display bulb


I'll have to see a manual but I think its around 6 volts.

Mar 10, 2009 | Yamaha EQ-70 Home Equalizer

Not finding what you are looking for?
Yamaha EQ-70 Home Equalizer Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Equalizers & Crossovers Experts

Steve

Level 3 Expert

3287 Answers

Paul Bade

Level 3 Expert

1392 Answers

Gil Shultz

Level 3 Expert

3250 Answers

Are you a Yamaha Equalizer and Crossover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...