Question about Canon MX300 Office All-In-One Printer

1 Answer

I have a Canon MX300 which has been bought 2nd-hand. There are new Canon original inks installed. When I switch on there is brief activity then power and error lights flash alternately. The display panel shows "Check printer" and "9000" flashing Any help would be appreciated.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 310 Answers

Is verry bad,the printer have logic board defect....you need to replace the logic board.I look in the service manual and 9000 error means to replace the logic board.If i have been useful please give me a vote :).Thanks

Posted on Apr 04, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to set ink level on canon mx-320 after refill?


Apparently the problem is that you are choosing to install (according to Canon), cheap, aftermarket ink cartridges rather than Canon ones. Therefore the machine is not recognizing them. Try this procedure, found on another forum, that was supplied by one of the cheapo ink companies. Who better to know how to fool the machines than them. If they want to sell these ink carts, they better know who to make them work!

U051 Error Correction procedure.

1- Switch off the Canon MX300 and disconnect the power cable.

2- While press and hold the power button, Connect the power cable to electric socket.

3- While pressing the power button, press the "Cancel/Stop" button (red button). (press TWICE che "stop\cancel" button)

4- Now release the power button and the printer turns into a kind of factory mode. Wait for 10 seconds until it says "idle".

5- Press ">" (next button) once "Shipping Mode 3? then Press the "OK" button. Press "OK" again for "without cleaning". A test page will print.

6- Open the cover, like you are about to change the cartridges.

7- Disconnect the power cable again without switch off the printer.

8- Take out the both cartridges.

9- Close the cover.

10- Connect the power cable and turn on the printer.

11- Now just put the cartridges back and the ink level in the canon Pixma MX300 have full again.

Jan 14, 2015 | Canon Black Pixma Mx 320 High Quality...

Tip

How to Reset Ink Level Canon MX300 Cartridges


1. Switch off the Canon MX300 and disconnect the power cable.<br /> 2. While press and hold the power button, Connect the power cable to electric socket.<br /> 3. While pressing the power button, press the "Cancel/Stop" button (red button).<br /> 4. Now release the power button and the printer turns into a kind of factory mode. Wait for 10 seconds until it says "idle".<br /> 5. Press "&gt;" (next button) once "Shipping Mode 3&prime; then Press the "OK" button. Press "OK" again for "without cleaning".<br /> 6. A test page will print.<br /> 7. Open the cover, like you are about to change the cartridges.<br /> 8. Disconnect the power cable again without switch off the printer.<br /> 9. Take out the both cartridges.<br /> 10. Close the cover.<br /> 11. Connect the power cable and turn on the printer.<br /> 12. Now just put the cartridges back and the ink level in the canon Pixma MX300 have full again.

on Feb 17, 2011 | Canon MX300 Office All-In-One Printer

2 Answers

I have an MX300 printer. Whenever I try to copy, the screen reads v163 col. What does this mean?


Hey!!

Its telling you that the colour cartridge is empty or remaining ink unknown,the way to stop it is to press and hold down the stop button for about 7 seconds!!That disables the remaining ink volume detection.

Hope it helps!!

"remember to vote please"

Sep 06, 2011 | Canon MX300 Office All-In-One Printer

1 Answer

I have refiled an existing ink cartridge and now the printer keep displaying low ink and does not print? please advise? thanks michelle


Hi,

Do the reset and it will display the required ink level for your cartridges/printer.

1 Switch off the Canon MX300 and disconnect the power cable.
2 While press and hold the power button, Connect the power cable to electric socket.
3 While pressing the power button, press the "Cancel/Stop" button (red button).
4 Now release the power button and the printer turns into a kind of factory mode. Wait for 10 seconds until it says "idle".
5 Press ">" (next button) once "Shipping Mode 3′ then Press the "OK" button. Press "OK" again for "without cleaning".
6 A test page will print.
7 Open the cover, like you are about to change the cartridges.
8 Disconnect the power cable again without switch off the printer.
9 Take out the both cartridges.
10 Close the cover.
Connect the power cable and turn on the printer.
Now just put the cartridges back and the ink level in the canon Pixma MX300 have full again.

Regards,
Ron

Feb 25, 2011 | Canon MX300 Office All-In-One Printer

1 Answer

Installed new ink cartridges mx 300, compatible B&W 40, color 41, printer status still says low ink, printing as if it is low ink. properly installed, tape removed, what i miss? can I check something...


Do you know what?. As a matter of fact,it is not compatible cartridges you buy. It is refurbished cartridges that repackaged with other brand as if this is their product. I say it is original cartridges that once empty and repackaged. So that's why when you install the cartridge the ink level stays low. You can make it sure by comparing it with new original cartridge. Find original cartridge,may be you can borrow from someone,which ink level still full and install on your printer. I am a hundred percent sure ink level will show properly :).

Feb 19, 2011 | Canon MX300 Office All-In-One Printer

1 Answer

5100


Hello there ok

Try
Here the Solution to reset the ink level for Canon Pixma MX300 follow this steps to reset the ink level in your canon MX300.

1. Switch off the Canon MX300 and disconnect the power cable.
2. While press and hold the power button, Connect the power cable to electric socket.
3. While pressing the power button, press the “Cancel/Stop” button (red button).
4. Now release the power button and the printer turns into a kind of factory mode. Wait for 10 seconds until it says “idle”.
5. Press “>” (next button) once “Shipping Mode 3′ then Press the “OK” button. Press “OK” again for “without cleaning”.
6. A test page will print.
7. Open the cover, like you are about to change the cartridges.
8. Disconnect the power cable again without switch off the printer.
9. Take out the both cartridges.
10. Close the cover.
11. Connect the power cable and turn on the printer.
12. Now just put the cartridges back and the ink level in the canon Pixma MX300 have full again.
Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks


Feb 07, 2010 | Canon MX300 Office All-In-One Printer

2 Answers

Canon mx300 not printing


Hi
It is ink low error U051

1. Disconnect the power cable
2. Connect it while holding down the power button
3. With the power button still down, press twice the "Cancel/Stop" red button
4. Release the power button
5. The prints turns into a kind of factory mode...(wait for about 10 seconds, utile it says "Idle")
6. Press the ">" (next to the "OK" button) once.” Shipping Mode 3"
7. Press the "OK" button.
8. Press "OK" again for "Without cleaning"
9. A test page will print.
10. Open the cover, like you are about to change the cartridges.
11. Disconnect the power cable again.
12. Take out both cartridges.
13. Close the cover.
14. Connect the power cable once again.
15. Turn the printer on.
16. Now just put the cartridges back...

Or try this

Here the Solution to reset the ink level for Canon Pixma MX300 follow this steps to reset the ink level in your canon MX300.
  1. Switch off the Canon MX300 and disconnect the power cable.
  2. While press and hold the power button, Connect the power cable to electric socket.
  3. While pressing the power button, press the “Cancel/Stop” button (red button).
  4. Now release the power button and the printer turns into a kind of factory mode. Wait for 10 seconds until it says “idle”.
  5. Press “>” (next button) once “Shipping Mode 3′ then Press the “OK” button. Press “OK” again for “without cleaning”.
  6. A test page will print.
  7. Open the cover, like you are about to change the cartridges.
  8. Disconnect the power cable again without switch off the printer.
  9. Take out the both cartridges.
  10. Close the cover.
  11. Connect the power cable and turn on the printer.
  12. Now just put the cartridges back and the ink level in the canon Pixma MX300 have full again.


Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Nov 02, 2009 | Canon MX300 Office All-In-One Printer

1 Answer

Cant print using Canon Pixma MX300


Hi


1. Disconnect the power cable
2. Connect it while holding down the power button
3. With the power button still down, press twice the "Cancel/Stop" red button
4. Release the power button
5. The prints turns into a kind of factory mode...(wait for about 10 seconds, utile it says "Idle")
6. Press the ">" (next to the "OK" button) once.” Shipping Mode 3"
7. Press the "OK" button.
8. Press "OK" again for "Without cleaning"
9. A test page will print.
10. Open the cover, like you are about to change the cartridges.
11. Disconnect the power cable again.
12. Take out both cartridges.
13. Close the cover.
14. Connect the power cable once again.
15. Turn the printer on.
16. Now just put the cartridges back...

Or try this

Here the Solution to reset the ink level for Canon Pixma MX300 follow this steps to reset the ink level in your canon MX300.
  1. Switch off the Canon MX300 and disconnect the power cable.
  2. While press and hold the power button, Connect the power cable to electric socket.
  3. While pressing the power button, press the “Cancel/Stop” button (red button).
  4. Now release the power button and the printer turns into a kind of factory mode. Wait for 10 seconds until it says “idle”.
  5. Press “>” (next button) once “Shipping Mode 3′ then Press the “OK” button. Press “OK” again for “without cleaning”.
  6. A test page will print.
  7. Open the cover, like you are about to change the cartridges.
  8. Disconnect the power cable again without switch off the printer.
  9. Take out the both cartridges.
  10. Close the cover.
  11. Connect the power cable and turn on the printer.
  12. Now just put the cartridges back and the ink level in the canon Pixma MX300 have full again.


Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Sep 08, 2009 | Canon PIXMA MX300 All-in-One Printer

Not finding what you are looking for?
Canon MX300 Office All-In-One Printer Logo

262 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

old marine
old marine

Level 3 Expert

1924 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...