Question about Stanley Tools Staple/Brad Nail Gun

Open Question

How do i fill and use my stanley 69-702 staple gun. Have lost instructions.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: Inserting brads into my Stanley

I bought one of these guns today and I had the same problem and it took me about 2 hours to figure it out as the instructions were very poor. Here how to load the brad nails:-

(a) Pull the slider bar all the way out
(b) Place the brad nail stick on the left side, IN FRONT OF the slider, NOT in the narrow gap in front of the two arrows where it says "LOAD BRADS"
(c) The nail heads should be facing the handle of the gun
(d) Close the slider and lock it
(e) Try it out. I tried nailing hardboard onto chipboard. The lever at low power only put the nail in about 30%. On Hi power it went in about 80%.

Good Luck
Peter

Posted on Jan 31, 2009

CaptAdams35
  • 28 Answers

SOURCE: how do you load nails in stanley tr250 staple and

The magazine on the TR250 has a recess on one side as well as a relief at the top where the driver pushes them through the opening. Load the brads/nails on that side of the magazine and it should operate properly. AS A REMINDER: ALWAYS REMOVE NAILS/STAPLES/BRADS WHEN NOT IN USE AS THIS WILL WEAKEN THE SPRING AND CAUSE FEED PROBLEMS IN THE FUTURE.

Posted on Mar 09, 2010

rowdy45176
  • 2176 Answers

SOURCE: how do I load nails in Stanley powershot staple/brad nails

you can try and go to Stanleytools.com and get to their knowledge base of FAQ or they have a direct way to contact the company for the information you need. I was on their site and have seen better to help the end user.

Posted on Dec 30, 2008

jj505
  • 195 Answers

SOURCE: Can you help with loading

Look at rear handle bottom, Push in then pull out,load. Please rate. Thanks

Posted on Mar 23, 2009

  • 342 Answers

SOURCE: Need help loading staples in my Stanley electric staple/nail gun

there should be a button / lever at the rear press it and it should open so as to insert the staples

Posted on Apr 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I load the stapler?


No you don't. We answer most things here.

If the stapler is like any of these

http://www.amazon.com/s?ie=UTF8&page=1&rh=i%3Aaps%2Ck%3Abostitch%20staple%20gun

You push the back in slightly to unlatch it and then drop it down a bit and the staple pusher comes out completely.

Jan 28, 2016 | Heavy Duty Stanley Bostich Heavy-duty...

1 Answer

How to put back together


Stanley Model TR45 Light Duty Staple Gun Review - YouTube

? 3:35
https://www.youtube.com/watch?v=hWmvXhkqnYI
Jul 25, 2012 - Uploaded by Vansvideoreviews
Stanley Model TR45 Light Duty Staple Gun Review ... How toPut Staples in a Craftsman Stapler (Model 968447) ... Stanley SharpShooter Manual Staple and Brad Gun review - Duration: 9:35. by Unpack Guy 35,948 views.

How to load staples into a Stanley Stapler - YouTube

? 2:11
https://www.youtube.com/watch?v=j4Q5W0uKS-s
Mar 26, 2013 - Uploaded by David DeStefano
This video shows you how to load staples into a Stanley StaplerModel # TR110. ... Stanley SharpShooter Manual Staple and Brad Gun review ...

put stanley sharpshooter staple gun back together ... - Fixya

www.fixya.com > Forum > Tags
Find solutions to your put stanley sharpshooter staple gun back together question. ... staples for the TRE500 Stanley Sharpshooter Electric Heavy Duty Stapler.

Dec 10, 2015 | Stanley SHARPSHOOTER HEAVY-DUTY STAPLE GUN

1 Answer

Why is my Stanley TRE 500 locking up after stapling a short time. What is the + and - on top for? I have lost my manual.


Make sure you are using the right staples for it. This will prevent lockups. You can also try spraying the staple track with a dry silicone lubricant.

The Plus and Minus is to set the strike pressure. Low for cork board, high for oak paneling.

Here is the manual, the TRE550 is close enough.

Stanley TRE550 Electric Staple Brad Nail Gun

Sep 21, 2014 | Electric Stanley Tre500 Staple Gun /...

1 Answer

HOW TO LOAD BRADS IN STANLEY TRE500


Please download the instruction sheet from the following link which explains how to load the brads. Make sure you have the correct size of brads mentioned at the bottom of the instruction sheet.

TRE500 Sharpshooter Stapler Instruction Manual

Aug 13, 2014 | Electric Stanley Tre500 Staple Gun /...

1 Answer

Loading staples into a Stanley sharpshooter staplegun


There are 4 staplers in the Stanley SharpShooter family. You drop the staples on top of the "slide out loader," then slide it into the gun. See models and staple sizes below:


TR150HL Stanley Sharpshooter
  • Stanley SharpShooter TRA700 series or Arrow T-50 heavy duty staples

TR150 SharpShooter
  • Stanley SharpShooter TRA700 series or Arrow T-50 heavy duty staples

PHT150C SharpShooter Heavy Duty Hammer Tracker
  • TRA700 series or Arrow T-50 heavy duty staples (1/4"-3/8")

TR250 SharpShooter Plus Heavy Duty Staple/Brad Nail Gun
  • Stanley SharpShooter TRA700 series or Arrow T-50 heavy duty staples and 1/2", 9/16" and 5/8" Brads

More information on the Stanley SharpShooter and a quick loading demo can be found here: http://www.expotv.com/videos/reviews/12/134/StanleyTR150HLSharpShooterHeavyDuty/185661

Sep 11, 2012 | Stanley Proto Stanley TR150HL SharpShooter...

1 Answer

Need instructions for a stanley sharp shooter tr45 on how to load


at bottom back of stapler find the metal clip, about 1/2 x 3/4 inch piece. push in and down at the same time. after it releases pull straight out. insert staples, assemble in opposite order

Mar 06, 2011 | Stanley Tr45 Sharpshooter Light Duty...

1 Answer

Need help loading staples in my Stanley electric staple/nail gun


there should be a button / lever at the rear press it and it should open so as to insert the staples

Apr 05, 2010 | Stanley Staple/Nail Gun Elec

1 Answer

Staples don't drive deep enough. How do I adjust depth.


http://www.stanleytools.com/default.asp?TYPE=STATICLEFT&PAGE=knowledgebase.htm&LEFT=left_knowledgebase.htm
Go to website and type in tre550 and you will find a copy of a PDF instruction. It is very limited. They also have a tool tips area.

Feb 25, 2009 | Electric Stanley Tre500 Staple Gun /...

1 Answer

How do I load nails in Stanley powershot staple/brad nails


you can try and go to Stanleytools.com and get to their knowledge base of FAQ or they have a direct way to contact the company for the information you need. I was on their site and have seen better to help the end user.

Dec 22, 2008 | Stanley Tools Staple/Brad Nail Gun

Not finding what you are looking for?
Stanley Tools Staple/Brad Nail Gun Logo

Related Topics:

1,321 people viewed this question

Ask a Question

Usually answered in minutes!

Top Stanley Tools & Hardware - Others Experts

John Trevino

Level 3 Expert

1383 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

JOHN LAPIER

Level 3 Expert

2428 Answers

Are you a Stanley Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...