Question about Haier HDP18PA Stainless Steel Free-Standing Dishwasher

1 Answer

Dishwasher does not go past first cycle and constintly continues to wash put on at 9am came home at 6pm and was still going

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 196 Answers

You have either a faulty element or thermostat. Your timer is controlled by the temperature, it wont click on until it reaches the correct temperature. If you want to try and fix then SWITCH POWER OFF and pull machine out.
1) Remove all water from inside
2) Put machine on left hand side and remove bottom panel if possible. Normally 2 or 4 screws. If not then remove front kick plate and panel behind.
3) Locate thermostat, should be a small round device attached to the bottom of the tank and will have 2 wires connected to it, there may also be a high limit stat beside it if so then you will need to replace both of these. You can get them from online spares sites and inputing your make and model and selecting the stat set.
3) If this doesn't help then you will need to replace the element.

Hope this helps.

Posted on Apr 04, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Samsung DMT300RFW Builtin Dishwasher will not run past wash cycle. I start it and it fills and the wash cycle starts but won't cycle past the wash cycle. No error codes.


What do you mean, it won't "run past the wash cycle"? Do you mean it stays in the wash cycle forever? Or do you mean it quits in the wash cycle and doesn't rinse or dry?

Oct 18, 2014 | Samsung DMT300RFW Builtin Dishwasher

1 Answer

Is TI chip covered on samsung dlp model HLT6187SAX/XAA?


I don't believe the manufacturer is covering this any longer, but you can try calling Samsung support at 1-800-726-7864 Call 1-888-899-7609
Mon. - Sun. 9am - Midnight (EST) Hearing-Impaired (TTY) 1-888-899-7608
Mon - Sun : 9am - 6pm (EST) Home Appliances Hours of Operations Mon - Fri : 8am - Midnight
Sat : 9am - 5pm
Sun : Closed Laptop, Printer, Galaxy Tabs (WiFi only) 1-800-SAMSUNG (1-800-726-7864)
Mon - Sun : 24hrs

the part# for your DLP chip is : 4719-001985
see the following web site: http://www.samsung.com/us/support/contact

the

Jul 06, 2014 | Samsung DLP HL-P4663W 46" Rear Projection...

2 Answers

Error message ERR


Product Phone Number Hours Support Website SURFboard® Cable Modems and Gateways 1-877-466-8646 Sun-Sat 7AM-11PM CST Website link Touchstone Cable Modems, Gateways and EMTAs 1-877-682-7747 Sun-Sat 7AM-11PM CST Website link DSL Modems and Gateways 1-877-466-8646 Sun-Sat 7AM-11PM CST Website link Video 1-877-466-8646 Sun-Sat 7AM-11PM CST Website link Software 1-877-466-8646 Mon-Fri 8AM-8PM CST Website link

For other Motorola products, please visit the product's website for your support questions.
Product Phone Number Hours For general product questions and technical support
on your Android-powered Smartphones and Devices
e.g. Motorola XOOM™, DROID RAZR™, DROID Pro,
Motorola ATRIX™ 4G, MOTOACTV™ 1-800-734-5870 Mon-Fri 7AM-10PM;
Sat-Sun 9AM-6PM CST Motorola Fitness Devices
e.g. MOTOACTV 1-800-734-5870 Mon-Fri 7AM-10PM;
Sat-Sun 9AM-6PM CST Non-Android Mobile Phones & Accessories
e.g. Motorola Karma™ QA1, MOTORAZR2™ V9,
MOTO™ W233 renew 1-800-331-6456 Mon-Fri 7AM-10PM;
Sat-Sun 9AM-6PM CST iDEN i-series/ic Series
e.g. i776, i425
(Nextel, Boost Mobile, and Southern Linc) 1-800-453-0920 Mon-Fri 7AM-10PM;
Sat-Sun 9AM-6PM CST TTY Support 1-888-390-6456 Mon-Fri 8AM-5PM CST
reference: http://arris.force.com/consumers/pkb_Home_ConsumerCallUsPage
Call Us

Mar 20, 2014 | Motorola Televison & Video

1 Answer

My Dishwasher (Westinghouse907 series) will not advance past the prewash/rinse cycle. I have cleaned out the filters. I also turned it off for a while and when I turned it back on it worked, but has now...


Hi


Thanks for using FixYa. If the cycle doesn't complete, then the first thing that should be checked is the Timer and then the heating element. Timers don't often fail. But if every other part of the dishwasher seems to be working properly and the timer knob seems to be stuck in one place--doing one function continuously--the timer may be at fault. Dishwasher timers can't be repaired. If yours is defective, replace it. Many dishwashers heat the wash and/or rinse water to a higher temperature, as the cycle calls for it. In these cycles, the dishwasher pauses after it has filled with water, waiting for the water to reach the pre-set temperature. What happens next depends, as follows: On some units, the pause is timed and the unit continues after the allotted time. On others, the cycle can't continue until the water reaches the higher temperature. If you have this type of dishwasher and the water isn't being heated (say, because of a problem with the heating element or thermostat), after the unit stops at the heating cycle, it never continues. When you repair the heating-system problem, the "cycle problem" is fixed too. Please do accept the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

May 23, 2010 | Westinghouse 24 in. MDP531 RF...

1 Answer

Du1100xtpq7 dish washer keep repeating wash cycle doesn't go past this just keeps washing


Hi


Thanks for using FixYa. If the cycle doesn't complete, check these:
Water-heating cycle
Many dishwashers heat the wash and/or rinse water to a higher temperature, as the cycle calls for it. In these cycles, the dishwasher pauses after it has filled with water, waiting for the water to reach the pre-set temperature. What happens next depends, as follows:

On some units, the pause is timed and the unit continues after the allotted time.

On others, the cycle can't continue until the water reaches the higher temperature. If you have this type of dishwasher and the water isn't being heated (say, because of a problem with the heating element or thermostat), after the unit stops at the heating cycle, it never continues. When you repair the heating-system problem, the "cycle problem" is fixed too.

Timer
Timers don't often fail. But if every other part of the dishwasher seems to be working properly and the timer knob seems to be stuck in one place--doing one function continuously--the timer may be at fault. Dishwasher timers can't be repaired. If yours is defective, replace it.


Please do accept the solution if the issue is resolved or else revert for further assistance.

Thanks
Rylee


Jan 07, 2010 | Whirlpool 24 in. DU1100XTPS Built-in...

2 Answers

Smeg integrated dishwasher continually washing - won't move to drying cycle.


you should check the heating element. if the water is not hot enough, the timer will not advance. crack open the door mid-cycle. let the water stop flying around. then open it all the way up. if you don't get a big ball of steam, you have an indication that your heating element may not be working properly. this is not too hard to check the resistance with a multimeter and then replace, if necessary. good luck

Nov 02, 2009 | Smeg STA4645U 18" Fully Integrated...

2 Answers

Whirlpool Quiet Partner Doesn't finish cycle


FIX YA IS A JOKE I WOULD LIKE TO BURY THE ************** WHO CREATED IT!

Jul 30, 2008 | Whirlpool GU2400XTP Built-in Dishwasher

3 Answers

Dial gets stuck


MOST DISHWASHERS HAVE A PAUSE DURING THE HEAT
CYCLE IF TH WATER ISN'T HOT ENOUGH OR IF A HIGH
TEMP WASH IS SELECTED. NORMALLY, THE TIMER WILL
ADVANCE WHEN THE TEMP IS HOT ENOUGH TO TRIP THE
THERMOSTAT. IF IT NEVER GOES PAST THAT POINT, THERE MAY BE A FAILURE IN THE HEATER CIRCUIT.

Feb 03, 2008 | Danby 22 in. DDW396 Free-standing...

1 Answer

Dishwasher


there is no quick fix. for a start, check continuity on the heater

Jul 04, 2007 | Hotpoint 24 in. FDW60 Free-standing...

Not finding what you are looking for?
Haier HDP18PA Stainless Steel Free-Standing Dishwasher Logo

179 people viewed this question

Ask a Question

Usually answered in minutes!

Top Haier Dishwashers Experts

Tim Doolittle
Tim Doolittle

Level 2 Expert

114 Answers

Tom Chichester

Level 3 Expert

34821 Answers

Bill Boyd

Level 3 Expert

42818 Answers

Are you a Haier Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...