Question about Jacuzzi Nova Whirlpool Tub H532

1 Answer

My MAAX jacuzzi runs on its own. After it is shut off and then turned on again, it is hard to shut off. And then in about 10 - 20 minutes (it varies) it will start up by itself, even without water in the tub. I have to press the shut off button several times to get it to stop.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 20 Answers

Power switch appears to have a short in it. See the dealer you purchased the tub from and have them install the part.

Posted on Apr 04, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Maax c02 error


[PDF]WHIRLPOOL BATHTUB OWNER'S MANUAL BAIN ... - Maax

www.maax.com/~/media/.../10050073_2009-04-17.p...

Translate this page Never operate the whirlpool system if there is less than 2". (5 cm) of water over the highest whirlpool jet (except for the back jets) or if the bathtub is empty.

Maax co2 error Bathtubs & Whirlpools Questions & Answers ...

www.fixya.com > Forum > Tags > co2 error > Bathtubs & Whirlpools
Maax bathtubs & whirlpools co2 error related questions and answers. Ask your Maaxquestions. Get free help from bathtub and whirlpool experts.

Maax bathtub c02 and e06 error - Fixya

www.fixya.com/support/t19321104-maax_bathtub_c02_e06_error
Aug 10, 2013 - maax bathtub c02 and e06 error - Maax URBAN 6032 HYDROFEEL AEROFEEL ... Jan 18, 2013 ' Maax Adagio True Whirlpool System.

How to Troubleshoot a Maax Tub ' eHow


Jan 05, 2016 | Maax Home

1 Answer

Lasco bubbler massage tub


Sounds like you may have a circuit that is bad in the control box under the tub.
Very unusual for that type of issue unless there is a problem on the circuitry.
Call a technician to have them trouble shoot it for you. It may need to be replaced. Those are not usually an item that is fixed.

Rod
US Parts Center

Feb 02, 2014 | Jacuzzi Nova Whirlpool Tub H532

1 Answer

Burning smell


get it checked by electrician. there has to be an access panel.

Oct 10, 2013 | Jacuzzi Home

1 Answer

Air massage runs 20 min. then shuts down. when I restart it right away it only runs a short time.


air systems have a built in timer on them. 20 mins.
they are supposed to be shut off for 20 mins to cool the blower down then can be turned on again.

Feb 13, 2011 | Maax Home

2 Answers

I HAVE A MAGNUM FORCE PUMP. iT WAS RUNNING THIS


It could be the capacitor again, but most likely if it stopped while running, its not that, unless you had a brief power failure. The motor may have a built in thermal overload which turned the pump off. If it only humms then it could either be locked up by something in the impller, or could be the bearings in the motor have failed. If the motor doesn't smell "burnt" then you might stand a change to disassemble the pump. Disassemble the motor and replace bearings. Replace the mechanical seal while you have it apart. OR you could buy a new motor, as it is 10 years old.

Jul 05, 2010 | Jacuzzi MAGNUM POOL PUMP 1-1/2 HP MAGNUM...

1 Answer

RapidHeat In-Line Heater U395000 [ Bathtubs and Whirlpools,: My jacuzzi tub jets run for ONLY about 5 minutes b...


you have a bad motor - when a motor overheats there is a sensor inside the motor that will shut if down so as to not damage the windings and such. once your tub has cooled down for 10 mins or so it will turn back on. the fact that you can push the button multiple times just means that you are turning the air switch on the back of the motor on/off until you get to the point where the motor has cooled down and will turn back on. if you do not push the air button after the tub shuts down and you finish your bath then when the pump cools down it will come back on because the air switch in the motor is latching i.e. it is either on or off. Since you left it in the on position the motor will come back on once the motor has cooled down.

May 17, 2010 | Jacuzzi RapidHeat In-Line Heater U395000 [...

1 Answer

WHAT DOES THE WARRANTY COVER


It all depends on the manufacture, Jacuzzi, Aquatic, Maax. They all have different warranties and what is covered. Best to call or e-mail the manufacturer of the tub with the date of pruchase and serial number.

Aug 27, 2009 | Maax Kashmir Hydromax Whirlpool with...

1 Answer

Pump won't shut off


You need a new impeller kit. Does any one know where to find one?

Jan 21, 2009 | Jacuzzi ALADDIN GO-KIT14 JACUZZI MAGNUM...

1 Answer

Jacuzzi


you have to call the maker of your unit because the gasket can start leaking if you use the rong kind of cleaner

Dec 12, 2008 | Maax Studio 1-Piece Hydromax Whirlpool Tub...

Not finding what you are looking for?
Jacuzzi Nova Whirlpool Tub H532 Logo

457 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jacuzzi Home Experts

Mike

Level 3 Expert

4336 Answers

john h

Level 3 Expert

12104 Answers

Donni Steen

Level 3 Expert

659 Answers

Are you a Jacuzzi Home Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...