Question about Onkyo TX-SR608 Receiver

1 Answer

What if went in safety mode, safety mode is froze in screen. Won't do anything

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 8,546 Answers

"Safety" mode - literally? I don't see that anywhere in the manual.

Page 13

Speaker Connection Precautions

(North American and Taiwan models) You can connect speakers with an impedance of between 6 and 16 ohms. If you use speakers with a lower impedance, and use the amplifier at high volume levels for a long period of time, the built-in amp protection circuit may be activated.

Page 66

The STANDBY indicator flashes red


The protection circuit has been activated. Remove the power cord from the wall outlet immediately.

Disconnect all speaker cables and input sources, and leave the AV receiver with its power cord disconnected for 1 hour. After that, reconnect the power cord and set the volume to maximum. If the AV receiver stays on, set the volume to minimum, disconnect the power cord, and reconnect your speakers and input sources. If the AV receiver turns off when you set the volume to maximum, disconnect the power cord, and contact your Onkyo dealer.

Generally speaking, an amp protects itself from heat, shorts, overloads and operator exuberance by refusing to turn on or stay on.


Overloads can be from excessive periods of high output or marginally low impedance loading by the speakers; and shorts would be wiring issues or a speaker blowing up.


You should be able to feel if it's hot. WHY is it overheating? Make sure it has sufficient ventilation on all sides and that vent holes are not blocked by dust balls. Ensure the fan (if equipped) is running as designed (some only operate on demand). Clean dust and debris from it.


If the amp comes back on after cooling, you're lucky. They only have so many self-protection cycles in their lives so continuously resetting or cycling their power without addressing the cause can do more harm than good.


If it protects immediately on a cool power up you should disconnect the speaker connections and try it 'naked'. If it comes up then diagnose which lead(s) are shorted. If it does not come up the problem is internal and should be left to an experienced and competent hands-on tech.

Posted on Apr 04, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My MiTraveler 1081W is froze on the setup screen. I went through the recovery process and now it's froze on the setup screen and won't do anything. Please help me if you can.


Sorry to be the bearer of bad news but sounds like your hard disk has crashed. Best get it replaced. Is the anyone you know who has a spare drive you can swop it out to check it with before you go out and start spending money

Nov 12, 2016 | Computers & Internet

1 Answer

Screen is froze. won't turn off. is making a constant clicking noise. can't move screen


system is hanged, direct power off and on if still not work then you have to run them in safe mode and uninstall the software you last installed or need to be formatted (as the same is also a reason of virus attack).


please vote me if found helpful.

Aug 01, 2011 | Computers & Internet

1 Answer

Wii froze and wont Turn off after playing game


dead disc? or disc reader? also why woulf turning the tv off help? did the wii overheat? or anything strange?

Apr 05, 2010 | Nintendo Wii Console

1 Answer

Screen froze up on't do anything


Try resetting it by sliding and holding power button for about 15 seconds. Go to http://www.sansa.com/support for more troubleshooting and FAQs. Hope this helps and don't forget to rate the answers.

Mar 06, 2009 | SanDisk Sansa Clip MP3 Player

1 Answer

I bought it yesterday and It already froze.


Try this: disconnect the player from the computer, turn it off, hold in the volume + button, and reconnect the player to the computer while holding the volume + button in. Keep holding the volume + button for an additional 5-50 seconds. Windows should eventually go into recovery mode and revive the player- it will pop up a window that says Found New Hardware Wizard.

Jul 05, 2008 | Philips GOGEAR SA6045 MP3 Player

1 Answer

Randomly Went to Recovery Mode


The hard drive is bad and you will need to get it replaced. There is a repair service box on this page if you scroll down; just enter your zip code to find a repair service near you.

Aug 16, 2007 | Creative Labs ZEN Vision:M Digital Media...

Not finding what you are looking for?
Onkyo TX-SR608 Receiver Logo

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Onkyo Audio Players & Recorders Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

 Grubhead
Grubhead

Level 3 Expert

5190 Answers

The Knight
The Knight

Level 3 Expert

74473 Answers

Are you an Onkyo Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...