Question about Whirlpool 25.6 cu. ft. Side-by-Side Refrigerator with In-Door-Ice Dispensing System

1 Answer

I've got a side by side Whirlpool refridgerator. The Water Filter status light is not indicating. What could be the problem and solution?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Whirlpool Master
  • 4,654 Answers

There are several pages that explain dispenser programming. This is on page 10 of the owners manual.

Water Filter Status Light (on some models)

The water filter status light will help you know when to change

your water filter. When the water filter status display changes from

"GOOD" to "ORDER," this tells you that it is almost time to

change the water filter cartridge. Replace the water filter cartridge

when the water filter status display changes to "REPLACE." If

water flow to your water dispenser or ice maker decreases

noticeably, change the filter sooner. The filter should be replaced

at least every 6 months depending on your water quality and

usage.

After changing the water filter, reset the status light by pressing

and holding the FILTER button for 3 seconds. The status light will
change from "REPLACE" to "GOOD" when the system is reset.

Changing the Water Filter

1. Press the eject button to release the filter from the base grille.

2. Pull the filter straight out.

3. Turn the cap counterclockwise to remove it from the filter.

IMPORTANT: Do not discard the cap. It is part of your

refrigerator. Keep the cap to use with the replacement filter.

4. Align the ridge on the cap with the arrow on the new filter and

turn the cap until it snaps into place.

NOTE: You can run the dispenser without a filter. Your water

will not be filtered. Simply insert the cap all of the way into the

base grille and rotate the cap until it is firmly in place.

5. Remove the covers from the O-rings. Be sure the O-rings are

still in place after the covers are removed.

6. Push the filter into the base grille. The eject button will pop

back out when the filter is fully engaged.
7. Flush the water system. See "Water and Ice Dispensers."

Water Filter Status Light:

The water filter status light will help you know when to change your water filter.

When the dispenser control panel's water filter status display changes to "ORDER," this tells

you that it is almost time to change the water filter cartridge.

Replace the water filter cartridge when the water filter status display changes to "REPLACE."

The filter should be replaced at least every 6 months depending on your water quality and usage.

NOTE: If water flow to your water dispenser or ice maker decreases noticeably, change the

filter sooner. After changing the water filter, reset the status light.

Details:

Pressing and holding RESET FILTER starts the 3 seconds countdown. Using the dispenser

cancels the countdown AND no dispensing is permitted. The number '3' blinks 3 times and the

'invalid' tone sounds 3 times and user has to release both the pad and the button and press

the button again to start it over

After 3 seconds, the BLUE WATER BARS in the Icon flash and an audible tone sounds 3
times. When the system is reset, the "ORDER" and "REPLACE" icons will disappear from the

display screen. See figure 16.
Note: Users can reset the filter status at any stage.

I've got a side by side Whirlpool refridgerator. - sea_breeze_131.jpg

If you should need the complete and exact model number and manual with parts manual you will need to enter the Model Number here=> sea_breeze_132.jpg Manuals, Guides and Instructions Please rate this solution, Thanks, Sea Breeze
User manual click HERE

Posted on Apr 02, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to get alarm to stop blinking after replacing water filter


Here is a list of refrigerator manufacturers and how to reset the filter change indicator light:
Amana- Press and hold the Auto and Dispenser Lock buttons until the water filter status indicator light flashes.
Frigidaire- Press and Hold the Reset Button Until the Indicator Light Flashes.
GE General Electric- Press and Hold the Reset Button for around 8 Seconds.
HotPoint- Press and Hold the Reset Button for around 8 Seconds.
Jenn-Air- Press and Hold The Water and Lock Buttons until the Water Filter light flashes.
Kitchen Aid- Press and Release the Light Button 5 times Quickly.
Maytag- Press and Hold The Light and Lock Buttons until the Water Filter light flashes.
Samsung- Press and Hold the Ice Type and Child Lock Buttons at the same time for 3 seconds.
Whirlpool- Press and Release the Light Button 5 times Quickly.

Dec 03, 2015 | Fagor FQ9925XUS

1 Answer

After i change the water filter de button of water still red


The water filter status light, located at the top of the refrigerator

compartment, will help you know when to change your water

filter cartridge.

Style 1 - Standard status light (on some models)

When the water filter status light changes from green to yellow,

this tells you that it is almost time to change the water filter

cartridge (90% of the filter life has been used). It is recommended

that you replace the base grille water filter cartridge when the

water filter indicator light changes to red OR water flow to your

water dispenser or ice maker decreases noticeably. See

"Changing theWater Filter Cartridge" later in this section.

After changing the water filter cartridge, reset the water filter

status light by pressing the light switch 5 times within
10 seconds. The water filter status light will change from red to
green when the system is reset.
If you need Adobe Reader Click=> Adobe Reader X (10.1.0) (50.25 MB)
If helpful please rate this solution, Thanks Sea Breeze
Click Photo Below for User Manuals


sea_breeze_227.jpg

Jul 29, 2011 | KitchenAid Superba KSRG25FK Side by Side...

1 Answer

How do you reset the water filter light on Model # ED5LHAXWQ00, Serial # HR02227866?


Hi, I found this handy guide:
Amana Refrigerators - Press and hold the Auto and Dispenser Lock buttons until the water filter status indicator light flashes.
Frigidaire Refrigerators - Press and Hold the Reset Button Until the Indicator Light Flashes.
GE General Electric Refrigerators - Press and Hold the Reset Button for around 8 Seconds.
HotPoint Refrigerators - Press and Hold the Reset Button for around 8 Seconds.
Jenn-Air Refrigerators - Press and Hold The Light and Lock Buttons until the Water Filter light flashes.
Kitchen Aid Refrigerators - Press and Release the Light Button 5 times Quickly.
Maytag Refrigerators - Press and Hold The Light and Lock Buttons until the Water Filter light flashes.
Samsung Refrigerators - Press and Hold the Ice Type and Child Lock Buttons at the same time for 3 seconds.
Whirlpool Refrigerators - Press and Release the Light Button 5 times Quickly.
Rich
Refrigerator Repair Meridian
Western Appliance Repair

Oct 02, 2010 | Whirlpool Refrigerators

1 Answer

I am replacing the water filter how do I reset on the outside door


The Water Filter Status Indicator Light serves as a
reminder to replace the water filter. A green light
indicates that the filter is in good condition. A red light
indicates the filter should be changed. Once light turns
red, it will remain red until function is reset.
To Reset Indicator:
• Press and hold both the Lock and Water
buttons simultaneously for four seconds. The
green filter status indicator light will flash
three times when the function has
successfully reset.
Thanks, Sea Breeze

May 17, 2010 | Jenn-Air JCD2295HES Side by Side...

1 Answer

Red light stays on after changing the water filter and running about 2 gallons through it


Water Filter Status Indicator
Light (select models)
The Water Filter Status Indicator Light serves as a
reminder to replace the water filter. A green light
indicates that the filter is in good condition. A red light
indicates the filter should be changed. Once light turns
red, it will remain red until function is reset.
To Reset Indicator:
• Press and hold both the Lock and Water
buttons simultaneously for four seconds. The
green filter status indicator light will flash
three times when the function has
successfully reset.

Nov 27, 2009 | Maytag MZD2665HE Side by Side Refrigerator

1 Answer

Change filter light


Water Filter Status Indicator
Light (select models)
The Water Filter Status Indicator Light serves as a
reminder to replace the water filter. A green light
indicates that the filter is in good condition. A red light
indicates the filter should be changed. Once light turns
red, it will remain red until function is reset.
To Reset Indicator:
• Press and hold both the Lock and Water
buttons simultaneously for four seconds. The
green filter status indicator light will flash
three times when the function has
successfully reset.
Sea Breeze

Nov 25, 2009 | Maytag MSD2650H Side by Side Refrigerator

1 Answer

Changing light after installing new water filter


Water Filter Status Indicator Light
(select models)
The Water Filter Status Indicator Light serves as a
reminder to replace the water filter. A green light
indicates that the filter is in good condition. A red light
indicates the filter should be changed. Once light turns
red, it will remain red until function is reset.
To Reset Indicator:
• Press and hold both the LOCK and WATER
buttons simultaneously for four seconds. The
green filter status indicator light will flash
three times when the function has
successfully reset.

Aug 12, 2009 | Jenn-Air 21.6 cu. ft. Side-By-Side...

1 Answer

Whirlpool gold side by side 2006 defrosting


temperature gadge must have been bumped, everything is working right now. Thanks

Jun 02, 2009 | Whirlpool Gold White-on-White 21.9 cu. ft....

1 Answer

No power to control unit in fridge


Turns out we had a bad control board. One of the coponets was blown and it had to be replaced. $400.00 and its good as new.

Dec 16, 2008 | Whirlpool 25.6 cu. ft. Side-by-Side...

2 Answers

Water Filter Indicator


I discovered by sheer luck that if I hold down the OK button for a few seconds the filter indicator changed from the flashing 1% to 99%.

Aug 01, 2007 | Whirlpool S20DRSS33 Side by Side...

Not finding what you are looking for?
Whirlpool 25.6 cu. ft. Side-by-Side Refrigerator with In-Door-Ice Dispensing System Logo

911 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Refrigerators Experts

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Charles T Nevin
Charles T Nevin

Level 3 Expert

4066 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Are you a Whirlpool Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...