Question about Lexmark X7675 Wireless All-in-One Printer
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
I had a similar problem, the scanner bar was stuck to the far left side. Here's how I fixed it:
1)Unplug the printer, disconnect any cables/phone lines to it.
2)Lift up the entire scanner bed housing(you will see the printer ink cartridges).
3)Locate the access patch (approx 1 cm x 1 cm square) along the left edge of the scanner bed housing(this is the side that closes in, next to the keypad buttons).
4)Using a small knife blade, peel off the patch from the corners and edges(it's sticky. Save it, you can stick it back over the hole when you're done).
5)Stick a pen through the access hole, and push the scanner bar to the right, approximately 2-3 inches.
6)Now, close the scanner housing, plug in the printer, and power it on.
It should reset and re-calibrate the scanner bar. If it doesn't, repeat steps 5) and 6) a couple times, until the printer correctly performs calibration. Then, you can put the sticky patch back over the hole, and you're ready to go. Hope this helps!
Posted on Jul 03, 2008
No solution here - just confirmation. Mine say that it (the scanner) cannot save files to my hard drive, that it is full. That's far from true, but to a dumb accessory a locked target folder/directory will look like a full disk. Does anyone know where Lexmark parks it's temporary files? I've looked in all the usual places on my Mac, and can't find anything yet. (I have previously found a Brother parks it's initial scans, before you save them, deep in a normally inaccessible corner of the System folder.)
Posted on May 24, 2010
Great job on trying to do it both ways, scanning and copying. Try to refresh the printer by uplugging the power adapter from the printer. The power adapter is the black box behind the printer where the power cord is attached. Make sure other end of the power cord is plugged in straight to the power outlet in the wall, bypass any surge device or power strips. Plugged the power adapter back in the printer after 30 seconds. It should automatically turn on. If not, press the power button. Try scanning and copying again. If problem persists, I strongly suggest you contact Lexmark Technical Support to further investigate the hardware problem in the printer. Hope I can assist you more on this.
Posted on Jun 29, 2010
Posted on Aug 28, 2010
SOURCE: broken hinge where do i
You can download the Manual to dis-assemble the Printer and purchase Parts for your Printer fro the below link:
Please let me know if I was Helpful...
Posted on Mar 05, 2011
Tips for a great answer:
Mar 10, 2011 | Lexmark X7675 Wireless All-in-One Printer
Mar 06, 2011 | Lexmark P3150 All-In-One InkJet Printer
Jan 19, 2011 | Lexmark C533DN InkJet Printer
Aug 11, 2010 | Lexmark X7675 Wireless All-in-One Printer
May 17, 2010 | Lexmark X7675 Wireless All-in-One Printer
Apr 21, 2010 | Lexmark X7675 Wireless All-in-One Printer
Apr 16, 2010 | Lexmark X7675 Wireless All-in-One Printer
Mar 31, 2010 | Lexmark Z1300 InkJet Photo Printer
Oct 11, 2009 | Lexmark X7675 Wireless All-in-One Printer
Mar 23, 2009 | Lexmark X7675 Wireless All-in-One Printer
363 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: