Question about Hobart SR24-H Built-in Dishwasher

Open Question

Hobart AMXXS1300. It doesn't seem to be heating up, the temp goes to 78/60 Celsius then the 78 goes back down to 61 only to heat up again.. seems like its a non-stop cycle. normally takes 45mins to heat up, apprently thats not normal?? i found out that the machine has NEVER been filled with salt before previously since new, can this be the root to the problem?? what can i do now?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 68 Answers

SOURCE: Hobart LX 18 problem

You are having a problem with the fill valve. If the unit fills AT ALL, with the power off, the fill valve is the issue.

It is a gold color valve behind the front kick panel. It has a large castle-like cap. Sometimes debris is the cause of your failure. (50/50). Turn off the water, and just take it apart slowly and pay attention to the plunger and spring. Take out the diaphram and screen, and clean it. There should be just one small hole in the diaphram. If cleaning doesn't help, you need to buy a rebuild kit. If you get the "ML" off the data plate, I can get you the kit P/N.

good luck

Posted on Jun 24, 2008

  • 93 Answers

SOURCE: hobart dishwasher lx 30 h

Did the clean light indicator blinking over n over? check the element wire harness connector. If disconnected fix it and run your dishwasher again.

Also you may check the continuity of your heating element.

Posted on Jul 23, 2008

kermit854
  • 38 Answers

SOURCE: hobart lx30 E3 error

Error Code E3 relates to a problem with the fill. Specifically that the water level has not been recognized at the middle water sensor. This can be caused by a problem with the drain system as you describe, or by low water pressure to the machine (should be 15-25psi flow), or bad wire connection to this middle sensor.
Check for proper water pressure first (should be a gauge on the machine) during the fill. Then check / repair drain as needed. These will probably eliminate the problem

Posted on Aug 19, 2008

  • 49 Answers

SOURCE: Hobart AM-14 dishwasher

it has a time out function once float is up is your water pressure correct. if to low it will first few cycles be low but after the will get to correct level and that is to the top of grey plastic drain pipe it cannot or should not be higher then the Gray drain pipe top, it overflows out that any extra rinse goes down it. check the o-ring on bottom of that grey pipe you could be leaking out the drain in between loads you come back and half the water is gone.

Posted on Sep 30, 2008

whytfang
  • 170 Answers

SOURCE: E4 error after attempting to fill and get to temp

This is what I found for the E4 code...hope this helps...and thanks for rating my effort...The Fang.


Machine won't fill or won't fill high enough(LX18, LX30 display shows "E0," "E2," "E3," or "E4")

1.Low water pressure — check for clogged hose strainer; check that site water pressure meets minimum flow pressures.
2.Make sure probes are clean.
3.No water pressure — main water supply valves may not be working.
4.Drain valve open - turn machine off to drain machine, then on. Repeat twice (this assists in clearing any drain valve obstructions). Wait for machine to reach READY mode and press WASH. Slowly open door several seconds later and note water level. Close door; 30 seconds later, open door slowly and check that water level is the same as it was. If not, repeat the
OFF-ON procedure.
5. Delime machine.

Posted on May 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can you advise me how to increase the temp in my hot tub? Jazzi SKT338H. It seems to be working properly but I don't have the manual anymore


Either turn heat control dial up, or there should be a 2-button, one UP & another DOWN. Push UP button.
If a single Heat button, the push the button once, it will start to blink, then push again - if temp goes up, you are going in the right direction to get to your desired temp. If going down, then stop & wait till blinking stops - then push the heat button again, it will blink again, press again and now it should go in opposite direction.

Apr 19, 2015 | Pool & Spa

1 Answer

My 1999 Chevy Malibu runs hot? It started when it overheated. We changed the thermostat, then water pump, then temp sensor gauge and the temp gauge goes high but only when the heater stops blowing hot...


Air pockets will make the guage do that, and also cause your heat to come and go. Also, a poor radiator, as in rotting, or plugged up, will cause high temperature issues.

Sep 20, 2011 | 1999 Chevrolet Malibu

1 Answer

What temp should my golf run at if the cooling system is operating properly? Runs perfectly on the highway but when i stop start it goes from min temp to only half on the gauge but seems to be runnning...


the temp seems to be fine. 80degrees celsius or less in stop and go traffic is normal,especially since the cooling fans are working and coming on at the proper time. the what seems to be running rough is another problem that doesn't seem to related to the cooling system temp. may want to check the spark plugs for worn electrodes.

Aug 08, 2011 | 1994 Volkswagen Golf

1 Answer

I just had a flex multi split ductless system installed. when it comes to heating and cooling there seems to be about a 4 degree range between when the heating and cooling comes on and off. also,the...


Read your maunual. It might be normal. A 4 degree split in your set back heateing control is about normal. It is that way so you can turn your unit on and never really need to touch it again. When the temp goes up, cooling goes on. When the temp goes down, heating comes on.

Sep 28, 2010 | LG Heating & Cooling

2 Answers

Hobart dish machine low wash temp


make sure all the curtains are there ,also check for any baffles missing from mach. should be 2 1 on incoming side 1 on outgoing, also ck hood vents had problem before with vents wide open sucking heat right out of warewasher

Jan 09, 2010 | Dishwashers

1 Answer

Reset Heating/ AIr cond temp display as well as EXT temp ????


the temp display can be switched between celsius and farenheit readings, since the car is from europe the default is celsius, The manual has instructions on changing back, You have to hold 2 buttons on the display per the manual.

May 07, 2009 | 2003 Land Rover Discovery

1 Answer

Overheating 94 9000 aero


try new fan thermostat switch

Apr 05, 2009 | 1994 Saab 9000

Not finding what you are looking for?
Hobart SR24-H Built-in Dishwasher Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Dishwashers Experts

Jason

Level 2 Expert

211 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

handygirl911
handygirl911

Level 2 Expert

59 Answers

Are you a Hobart Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...