Question about Dishwashers

1 Answer

Pump continuing to run -Asko D3100

Machine appears to have had a flood fault,have removed water from overfill tray but pump contiues to run.Micro switch for flood level operates and tests ok. Is there another switch which indictes overfill inside cabinet that may cause pump to run continually?

L2 flashes and unit will not step on in program,have carried out a reset with no success,pump continues to run and L2 flashes. Is there a site where I can get a copy of the schematic diagram for this model.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Micro switch was actually faulty,moisture had entered the switch and caused internal tracking and shorting out the micro switch ,making the pump run continually as it thought it was still in flood mode.
Flood appears to have been caused by a pin hole in the water fill hose in the base of the dishwasher,causing water to spray on the micro switch and eventually biuld up in the base of the machine.

Posted on Aug 05, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Deloghi dw67s dishwasher, drain pump on continuously, showing E4 and no water in washer. What is used to detect the overflow?


Hello

There is a slight leak somewhere or the machine keeps overfilling causing the drain pan to activate via the flood switch.

remove all dish trays from washer, unscrew and remove lid off salt softener, almost and thoroughly remove as much excess water as you can, it could be the vacuum switch/water level float.. do the tip over again, and be sure you get it all,

replace all trays and softner lid and machine should work again.

Aug 09, 2011 | Dishwashers

2 Answers

I have an asko T760 Butterfly dryer. It is stuck on P2 but will not run. I shut off the unit, turned back on. The LCD flashes between P1-P4 and what they are, such as extra dry, dry, normal dry, & iron...


Hi.

The machine is telling you that there is overfill, f2 and 4 are faults with overfill system. Lights blinking, pump running and controls dead also indicate an over fill fault :

"1. Disconnect the power to the unit

2. Remove the lower access panels and check the tray under the dishwasher (you will probably find it is full of water)

3. Use a towel or a sponge to remove the water

4. There is a float that should stop the operation of the dishwasher and run the pump if water is in this tray. Check this pump to see if it is functional

5. Test the dishwasher

6. If there are no leaks from the dishwasher into the pan, check the drain hose under the sink

7. THE DRAIN HOSE MUST RUN UP TO THE TOP OF THE UNDERSIDE OF THE COUNTERTOP THEN DOWN TO THE DRAIN. (If the hose is not set up like this, water from the sink drain will flow into the dishwasher and overfill the tray"

Here all diagrams.

Regards.

Ginko.

Apr 26, 2011 | Asko T761 Electric Dryer

2 Answers

Overfilling fault


I believe the washer has had a flood type situation.there is normally a flood switch in the very bottom of the dishwasher right at the very floor,if water get into the bottom tray it floats a piece polystyrene foam wich triggers a little micro switch wich will run the pump continually & show Overfilling fault at the same time..The water in the tray needs to be mopped out with a rag or spunge so that the styrene foam can drop back down.The blockage you had may have caused this flood situation some how.The overfill fault was probably due to the washer not pumping out,So that may be ok now that you have cleared the blockage.hope this helped.

May 13, 2010 | Asko 24 in. D3530FI Built-in Dishwasher

1 Answer

D3350 F4 indicator


F4 This is a Fault with the water fill

Note: Lights blinking, pump running and controls dead indicates an over fill fault

1. Disconnect the power to the unit

2. Remove the lower access panels and check the tray under the dishwasher (you will probably find that it is full of water)

3. Use a towel or a sponge to remove the water

4. There is a float that should stop the operation of the dishwasher and run the pump if water is in this tray. Check this pump to see if it is functional

5. Test the dishwasher

6. If there are no leaks from the dishwasher into the pan, check the drain hose under the sink

7. The drain hose must run up to the top of the underside of the counter top then down to the drain. (If the hose is not set up like this, water from the sink drain will flow into the dishwasher and overfill the tray

Aug 05, 2009 | Asko Dishwashers

1 Answer

Asko d3100


Remove the lower panel at the back of the machine. If there is water on the bottom pan, wipe it up with a towel or so, and the machine schould be like new again ;-)

Good luck

Feb 05, 2008 | Dishwashers

4 Answers

Asko 1805 Frozen


Sounds like the controlunit is bad.

Jan 01, 2008 | Asko 24 in. 1805 Built-in Dishwasher

2 Answers

Asko diswasher


Remove the backpanel of the machine, and look if there is water at the bottom of the machine. If so, use a towel or so to dry up the water. This should solve the prob.

Nov 23, 2007 | Asko D1776 Stainless Steel Built-in...

2 Answers

Water flooding out


Hi KellyW,

 

The dishwasher drain hose may be clogged.  When the dishwashr starts up can you hear the water running into the Sink faucet drain. If not inspect the hose that attaches to the Sink Drain for restrictions.  Also in the bottom of the dishwasher you should have a filter.  If this filter is clogged you cannot expel water.  Clean the filter. 

Oct 23, 2007 | Asko D1776 Stainless Steel Built-in...

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

562 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

yadayada
yadayada

Level 3 Expert

74192 Answers

Owen Barnes

Level 3 Expert

867 Answers

Brad Brown

Level 3 Expert

15301 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...