Set up I can not set up my DVD, no reaction to remote control, no reaction manual bottons. Can you help me? Thanx

If you wish to get more details; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls.Common set-up codes to check with TVs and other devices are given, in the order of the "device's brand name" in alphabetical order.Pull up older posts. Surf the site with patience. Surf the sites by type in the brand name to your set, in its search box.
http://electronicshelponline.blogspot.com/
http://remotesearch.blogspot.com/
http://electro-medical.blogspot.com/
http://electrohelponline.blogspot.com/
Type in the brand name of your device, in the search box [at the top right] of the display window and the Search will start at once as you type in, and will show you all the related posts.It will make surf easy.

Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls. If you wish to get more; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. One among it has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the top right part of the display window. It will help you to find the document easily.
http://remotesearch.blogspot.com/
http://electronicshelponline.blogspot.com/
http://electrohelponline.blogspot.com/

There are two codes for Sharp. You'll have to try both to see which one works. 0048 & 0807. I am assuming you don't have a manual.
On the remote press and release the VCR/DVD button. Press and hold the SET button until the LED blinks twice. (it will blink once when you first press it, that doesn't count.) Just wait a few seconds. After it blinks twice, release the SET botton, and enter the CODE..
The LED should blink twice. Aim the remote at your VCR and press
POWER.. The VCR should turn on. If not, try the other code.
0048 worked on mine. Good Luck!

be sure your remote is ok. check the remote as follow:
-use a pocket radio that is set/tuned on AM-frequentie band.
-hold the remote near the receiver of the radio while pressing every botton one by one
-you should hear a high pitch sound if the remote is ok
-when all botton do the high pitch that means the dvd IR-receiver is bad. usually it can't be, those are tough....

if you dont got the pitch the remote is bad. test especially the power botton of the remote.

If it is the remote please write back. I will show you how to do some simple actions to get the remote back going..

succes

Answer is NO.
most dvd needs to be set by remote control, because they don`t have a menu access botton on the set.
look at E-BAY for a remote control for its kind.

Hi,


1.Turn on the component to be programmed, such as the television or DVD player.

2.Press the "Code Set" button on your Hitachi remote. The button is often located near the top with the separate component buttons.

3.Press the button for the component you wish to program with the Hitachi Remote(TV,DVD).

4.Enter the manufacturer's code for the component being programmed. The manufacturer's code can be found either in the Hitachi manual, the manual for the component being programmed or on the website of the manufacturer of the product.

5.Press the "Enter" button to submit the manufacturer's code.

6.Press the power button for the component being programmed. Make sure the remote is pointed at the correct component, and it should turn on if the program was entered correctly

Thanx

Hi,

1. Manually turn on the VCR/DVD/Cable set top box.

2. Press the VCR/DVD/Cable set top box button on the remote control.

3. Press and hold the SETUP button until the LED LIGHT flashes twice.

4. Enter the codes using the Number Buttons. If the code is accepted, the LED flashes twice after the last digit is entered.

If the LED does not flash twice, repeat Steps 2 through 4 with the next code listed for the component and
manufacturer.

5. Point the remote control at the VCR and press the POWER button. The VCR/DVD/Cable set top box will turn off.
6.Your are done.

Thanx

Auto code search

1. switch on the TV and select a channel eg. Bbc1 on the TV itself
2. press the appropriate device button eg. TV
3. press the green SET button for approx 5 seconds until the red light comes on.
4. release the green SET button and point the remote at the device to be controlled, the remote will emit a test signal about every 2 seconds.
5. when the TV switches itself off briefly press the green SET button to store the code found.
6. when the red light goes out the search is ended.
7. try out the remote if it works follow the same steps to set it to other devices eg. DVD. If it does not work follow the steps again.
cover other remote sensors on other devices when setting the remote.

Hi,
I am giving the site where there is a manual for setting up your jumbo universal remote control.

enablingdevices.com/files/downloads/401fe4d1-1d9e-4186-8d75-4ea2f4754513.pdf

Hope my info solve your problem,
Thanx for using Fixya,
Bye.

Slide down the cover on remote control.On the bottom right side you'll see a little switch(usually is cowered with the warning white little sticker).Slide that switch to DVD1(or DVD2 if somebody got different setting).Power up DVD/VCR combo press system menu botton,go to settings,change to DVD3(factory default)and there you go.Good luck.
Rich