Question about HP PSC 1350 All-In-One Thermal Printer

1 Answer

HP PSC 1300 All in one Printer

I can not find out how to replace the printer cartridge

Posted by on

  • 1 more comment 
  • Anonymous Aug 17, 2008

    HP PSC 1300 All in one Printer problem

  • playethic Dec 16, 2008

    I'm inserting at an angle, but I can't get cartridges to click into place.

  • carlvorman Jan 17, 2009

    I have the some problem It don"t print and show information "HP Print Utility error. I have HP 1350 All in One print test program and it show me all is OK.What to do?

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 28 Answers

Replacing the print cartridgesHP PSC 1300 All in one Printer - gtabtop.gif

  1. Turn on the HP PSC and lower the print-carriage access door.
    The print carriage will move into the access area. Figure 1: Opening the print-carriage access door
    c00034850.jpg
  2. After the carriage stops moving, push down on the top of the print cartridge to release it, and then pull it toward you out of the slot.
      NOTE: The black cartridge is on the right side of the print carriage.
    Figure 2: Removing the print cartridge

      NOTE: It is normal to see ink buildup in the print cartridge slots.

  3. Remove the new print cartridge from the packaging and gently remove the plastic tape by using the pink pull tab.
      CAUTION: Do not touch the copper contacts or ink nozzles. Install the cartridge immediately upon removing the tape to prevent ink from drying in the nozzles.
    Figure 3: RHP PSC 1300 All in one Printer - c00034852.jpglastic tape
    c00034852.jpg
  4. Push the new print cartridge into the appropriate slot at a slight angle, until it clicks into place.
      CAUTION: Do not attempt to push the cartridge straight into the slot. It must slide in at a slightHP PSC 1300 All in one Printer - c00034853.jpg Figure 4: Inserting the print cartridge
      c00034853.jpg
    • Close the print-carriage access door.


Using a photo print cartridHP PSC 1300 All in one Printer - gtabtop.gif/https://astro2w5a.cce.hp.com/webclient/Document?docname=c00033431&lc=en&cc=us#top">gtabtop.gif To use the photo print cartridge, remove the black print cartridge and insert the photo print cartridge in its place.
The photo print cartridge can be purchased separately and will optimize the quality of printed photos.
With the tri-color print cartridge and photo print cartridge installed, you have a six-ink system, which provides enhanced quality photos. For printing regular text documents, use the black print cartridge.
Use a print cartHP PSC 1300 All in one Printer - c00034854.jpgor to keep either print cartridge secure when it is not being used. Figure 5: Storing the print cartridge
c00034854.jpg 1 - Inserting the print cartridge
2 - Removing the prinHP PSC 1300 All in one Printer - gtabtop.gif

Aligning the print cartridgesgtabtop.gif After installing or replacing a print cartridge, the HP PSC will automatically print a cartridge alignment page.
  1. Place the alignment page face down on the left front corner of the glass with the top of the page facing the left side.
  2. Press Scan .
    The HP PSC will align the print cartridges. During the alignment the button LED will blink until the alignment is complete.

Posted on Sep 05, 2008

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: hp psc 1300 printer cartridge

The 'check print cartridge' light keeps flashing on my HP printer, so I replaced the cartridges and everything else i could think of such as restart my computer, temporarily disconnect the printer, etc. the light continued to flash. I also tried resintalling the printer software. Any ideas??

Posted on Apr 30, 2008

Niraj Limbu
  • 183 Answers

SOURCE: HP printer PSC 1410 ALL in one printer showing "Check print cartridge" error

Turn your printer off and turn it back on.

Posted on Feb 08, 2009

  • 1 Answer

SOURCE: HP psc 1300 printer

this printer does not print on photo paper...read the specs online about it....prints on regular stock paper but NOT photo paper....i have the same prob.....need to buy a photo paper compatable printer.

Posted on Feb 23, 2009

  • 160 Answers

SOURCE: replacement ink cartridge not printing

this has various reasons that this problem occurs.but the 1 simple solution is to get it properly work is to uninstall the printer driver and then reinstall it properly.this will definately work.

Posted on Jan 06, 2009

  • 1 Answer

SOURCE: HP printer PSC 1410 ALL in one printer showing "Check print cartridge" error

please let me know what is rail and carriage bushings ?

Posted on Jul 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an error message B200


Hi Kathleen,

to clear the Canon B200 error code:

Steps for 4+ Cartridge Printers
  1. Remove All Cartridges. Do whatever is necessary to remove the individual ink cartridges from your printer. In most cases this will be opening the lid of your printer and waiting for the cartridge cradle to move into the correct position.
  2. Remove the Printhead. This is easily achieved in most printers by simply lifting the orange/gray locking lever on the side of the cartridge cradle and then gently lifting the printhead from the printer.
  3. Reinstall the Printhead. Gently put the printhead back into your Canon Pixma printer and lock it into position firmly.
  4. Reinstall All Cartridges. Place all of the cartridges back into the printer and close any open doors. This makes sure that your printer is actively examining the reinstalled cartridges and printhead.
  5. Unplug the Printer. Physically remove your printers plug from the wall and leave it unplugged for 5+ minutes. This allows the printhead to cool and all residual electricity to leave the printer.
  6. Plug the Printer Back.
  7. Do a Nozzle Check or Cleaning Cycle. The B200 error does not tend to occur until your printer actively tries to use the printhead. As such I recommend performing one of these processes in an attempt to confirm the correct cartridge has been replaced.
Steps for 2 Cartridge Printers
  1. Turn the Printer off. When your printer is in this error state it will not let the cartridge cradle within the printer move. However resetting the printer should clear the error message temporarily allowing us to troubleshoot further.
  2. Turn the Printer Back on Again.
  3. Remove the Problem Cartridge. Whilst the Canon Pixma error messages do not tend to specify which cartridge is causing the problem, you should be able to have a rough idea based upon which cartridge was last replaced.
  4. Install a Replacement Cartridge. As the printhead is part of the cartridge, sadly there is no way to stop the B200 error without replacing the cartridge. I would recommend either installing a new cartridge or a previously used cartridge that you know to be functional.
  5. Do a Nozzle Check or Cleaning Cycle. The B200 error does not tend to occur until your printer actively tries to use the printhead. As such I recommend performing one of these processes in an attempt to confirm the correct cartridge has been replaced.
  6. If Necessary Replace the Other Cartridge. If the error persists with the new cartridge, it may be that the other cartridge has developed a fault and is the cause of the B200 support code. If at this point the error remians I can only recommend replacing the other cartridge.

Aug 11, 2017 | Office Equipment & Supplies

1 Answer

Directions for inserting ink cartridges


Replacing the Ink Cartridges for Deskjet 6940 and 6980 ...

support.hp.com/us-en/document/c00569593
Selecting the correct print cartridge, and removing and installing print cartridges. ... Damage may occur to the HP Deskjet printer if the print cartridges are not docked ...print cartridges, or continue to the sections below for detailed instructions.

Replacing a Cartridge - HP Deskjet 2540 All-in-One Printer

www8.hp.com/.../printers.../replace-ink...toner/.../replac...

Hewlett?PackardLearn how to replace a cartridge in the HP Deskjet 2540 All-in-One printer.

Replacing a Cartridge - HP Envy 4500 e-All-in-One Printer ...

? 3:56
https://www.youtube.com/watch?v=oJVYTXaI6e4
Jul 11, 2014 - Uploaded by HP Printer Support
The HP Instant Ink program is only available in the following countries - United ... ... Replacing a Cartridge - HP Envy 4500 e-All-in-One Printer ... HP ENVY 4500 WIRELESS SCANNERCOPIER REVIEW - Duration: 13:52.

Jan 16, 2016 | HP Office Equipment & Supplies

1 Answer

How to Replace catridge epson stylus c43sx


Are any of the cartridges empty or not? Always replace the cartridges with the printer on.

If you do not have any low ink alerts, you need to enter the maintenance mode. Press the Maintenance button (has both an ink drop and a paper symbol) and the Power button at the same time. Then open the black printer cover (lift up).

If any cartridges are low or out, just lift up the printer cover. Then press the maintenance button. The cartridge carrier will move the empty cartridge to the replacement position. (If both cartridges are out or you are using the Maintenance mode, the cartridge carrier will move the black cartridge to the replacement position.) Lift up the cartridge clamp (at the back of the carrier for current cartridge to replace; it will rotate towards you.). Then lift the cartridge up; dispose of the empty cartridge. Unwrap your new cartridge and remove the yellow tape (do not touch the IC chip or remove the other tape from the cartridge). Push the new cartridge straight down into the carrier.

Close the cartridge clamp and press the maintenance button to move the color cartridge to the replacement position. Repeat the cartridge replacement steps above for that cartridge. Close the printer cover. Then press the Maintenance button again and wait while the printer charges the ink system.

For pictures to go with the steps, see http://support2.epson.net/manuals/english/ij/stylusc43/REF_G/INK_1.HTM .

I hope this helps.

Cindy Wells

Sep 11, 2012 | Epson Stylus C43SX InkJet Printer

1 Answer

Printer ask for cartridges


turn off your printer...then replace new cartidges.after replacing cartridge restart printer...always when you want to change or replace cartridge/Drum/fixing/belt trun off your printer...

Jul 12, 2012 | Lexmark X9575 InkJet Printer

1 Answer

I have a epson tx300f printer I purchased four coloured ink cartridges I dont know how to replace them I need your help


Hi,
To replace your printer cartridge follow the steps below:
>Turn on the printer.
>Go to the Printer and Faxes wizard in the control panel.
>Right click on the printer and click on the printer properties, then go to the printing preferences.
>Go to the maintenance tab and select "Ink cartridge replacement" option.
>After this job the window automatically shows and gives instructions to replace the cartridge.
>Then just open the printer cover take out the old cartridges.
>Open the yellow sticker from the new cartridge and replace after a little shaking.
>All process you can see in the window, just follow the instruction and easily install the new cartridge.
After replacement align the cartridges and give a print job.

Apr 28, 2011 | Epson Office Equipment & Supplies

1 Answer

Replaced black ink cartridge and printer keeps asking to replace


The message that persists in saying to "replace black cartridge" could be due to a defective cartridge chip. The chip maintains counts and tells the printer when a new cartridge is installed. If you cartridge is remanufactured, they may have neglected to install a new chip.

Regarding the new fuser not working, I'll have to get back to you on that.

Oct 15, 2009 | HP LaserJet 4600dn Color Printer

1 Answer

Printer not working. The light flashes red six times.


Error Condition Indicator Beeps Error
Code Possible Solution Paper Feed / Delivery Orange 2 Remove any paper jammed Paper Jam Orange 3 Remove any paper jammed Ink Out Orange 4 Add Ink BJ Cartridge Misinstalled Orange 5 Re-install cartridge or replace it NO BJ Cartridge Orange 6 Re-install cartridge or replace it BJ Cartridge Error Orange 7 Re-install cartridge or replace it Waste Full warning Orange 8 Waste is almost full , needs service very soon Service Errors Blinks Beeps Error
Code
Possible Solution ROM Error 1 x Orange 10 6100 Try unplugging Printer RAM Error 2 x Orange 10 6300 Try unplugging Printer EEPROM 3 x Orange 10 6800 Try unplugging Printer Home Position 4 x Orange 10 5100 Temperature Sensor 5 x Orange 10 5400 Try unplugging Printer Waste Full 6 x Orange 10 5B00 Needs Service Cartridge OverHeat 7 x Orange 10 5200 Replace the BJ Cartridge(Printhead) Cartridge OverHeat 8 x Orange 10 5200 Replace the BJ Cartridge(Printhead) Cartridge Displaced 9 x Orange 10 5200 Replace the BJ Cartridge(Printhead) or reinstall Cartridge Displaced 10 x Orange 10 5200 Replace the BJ Cartridge(Printhead) or reinstall Cartridge Displaced 11 x Orange 10 5200 Replace the BJ Cartridge(Printhead) or reinstall Other Hardware error 12 x Orange 10 6500 Other Hardware error None None 5910 Needs Service Other Hardware error None None 5C00 Needs Service

Oct 01, 2009 | Canon S400 InkJet Printer

2 Answers

Borhers does not print


printer says cyan cartridge needs replacement, however when I replaced it, it says that there is no cartridge.
Betty

Nov 18, 2008 | Brother MFC 210C All-In-One InkJet Printer

1 Answer

I haven't the manual for this printer color laserJet 2600n series,


document.tlSearch.tx.value=unescape("") s.gif s.gif
HP Color LaserJet 2600n Printer - Installing Print Cartridges When a print cartridge approaches the end of useful life, the control panel displays a message recommending that to order a replacement. The printer can continue to print using the current print cartridge until the control panel displays a message instructing to replace the cartridge. The printer uses four colors and has a different print cartridge for each color: black (K), cyan (C), magenta (M), and yellow (Y). Replace a print cartridge when the printer control panel displays one of the following messages: Replace yellow cartridge, Replace magenta cartridge, Replace cyan cartridge, Replace black cartridge. The control panel display also indicates the color that should be replaced (unless a genuine HP cartridge is not currently installed). Change the print cartridge
  1. Turn off the printer.
  2. Open the front door. c00315320.gif CAUTION: Do not place anything on the transfer belt (ETB), which is located on the inside of the front door.
  3. Remove the used print cartridge from the printer. c00315321.gif
  4. Remove the new print cartridge from the bag. Place the used print cartridge in the bag for recycling. c00315322.gif
  5. Grasp both sides of the print cartridge by the blue handles and distribute the toner by gently rocking the print cartridge from front to back. CAUTION: Do not touch the shutter or the surface of the roller. c00315323.gif
  6. Remove the orange shipping locks and the orange shipping tape from the new print cartridge. Discard the shipping tape and shipping locks according to local regulations. c00315324.gif
  7. Align the print cartridge with the tracks inside the printer, and using the handles, insert the print cartridge until it is firmly seated. c00315325.gif
  8. Firmly close the front door. c00315326.gif
  9. Turn on the printer. After a short time, the control panel should display Ready.
    NOTE: If a cartridge is in the wrong slot or is the wrong type for the printer, the control panel will display one of the following messages: Incorrect yellow, Incorrect magenta, Incorrect cyan, Incorrect black.
  10. Installation is complete. Place the used print cartridge in the box in which the new cartridge arrived. See the enclosed recycling guide for recycling instructions.
  11. If a non-HP print cartridge is in the printer, check the printer control panel for further instructions.
    NOTE: When replacing or changing a black print cartridge, a cleaning page will automatically print. This helps prevent speckles on the front or back of printed documents. A cleaning page can also be generated using the control panel or the HP Toolbox.

Nov 03, 2008 | HP Color LaserJet 2600n Printer

2 Answers

Black ink cartridge


It seems that its an hardware issue with the printer as you have already replaced the cartridge with a new one.
If the printer is in warranty contact DELL to get the printer replaced.


I would also suggest you not to use refill cartridges. Always buy genuine cartridges. As using refilling cartridges spolis the printer.
It damaged the print heads in the printer.

May 30, 2008 | Dell 922 All-In-One InkJet Printer

Not finding what you are looking for?
HP PSC 1350 All-In-One Thermal Printer Logo

1,000 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Ben Johnson

Level 3 Expert

685 Answers

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2022 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...