Question about Dishwashers

1 Answer

GE dishwasher with tactile board. Worked fine until special fingers caused issue? Now only the CANCEL and timer light-up when CANCEL pressed. Pump runs to drain for 2 minutes. Stops. NOTHING. Dont see garbage under the float. moves freely up and down. Is there are RESET? Suggestions PLEASE mbetts1950

Posted by on

  • Greggmark1 Mar 28, 2011

    Send me complete model.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 77 Answers

This should help: PDW8000 series: press the resetbutton once. This will cancel the washing cycle and pump the water out of themachine. PDW9000 series: open the door aninch and wait for the machine to stop. Touch the reset button to cancel thewashing cycle and reboot the panel.
According to the GE Owner's Manual for the PDW9000 series only: If the"start/reset" light is flashing, close the door until the water pumpsout (this takes approximately 2 minutes) and the light stops flashing. When thelight stops flashing, the dishwasher can be reprogrammed and restarted. If the machine is unresponsive, killthe power to the machine by turning it off on the wall switch (if applicable)or turning the circuit breaker off. Leave the power off for 30 seconds,then turn the power back on. If thatdoes not work here is the repair info: Get into the service mode by pressingkeypads #8 and #4 for 3 seconds. Then reset from service mode. LINK to SCHEMATIC

Posted on Mar 28, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Dishwasher starts on its own (no house is not haunted). Start resume button flashes


have a service technician in as it appears to be a problem in the program board
could be moisture across the circuit board

Feb 06, 2016 | Maytag MDB7749AWQ Builtin Dishwasher

1 Answer

Reseting Timer


press cancel should reset control board.if not unplug for 5 min.there is no button to reset it! if dose not reste may be bad board

Jan 01, 2009 | GE 24 in. Profile PDW7800 Built-in...

3 Answers

Green light on kenmore dishwasher is flashing


I actually had to change the steps a little and this is what I did:

press heated dry
press normal wash
press heated dry again
press normal wash again
wait a few seconds
all the lights should come on
press cancel (should hear pump)
hit cancel again

Started a cycle and began washing.....Thx

Dec 31, 2008 | Kenmore 24 in. 16039 Built-in Dishwasher

1 Answer

Kenmore dishwasher not draining when finished full cleaning cycle


sounds like a cycle timer problem. Look for a loose wire on the cycle timer. If yours is a digital timer, it is a board issue. Sorry.

Aug 03, 2008 | Kenmore 24 in. 15932 Built-in Dishwasher

2 Answers

GE Max dishwasher no lights on panel


I have the same problem and actually found a workaround by mistake you may try as a temporary solution (if that works for you):

- press and hold the lock button for a couple of seconds
(the delay timer would increase by 1 hour)
- press and hold the lock button again
- repeat until it reaches 9hrs
- repeat one more time: the control panel should be functionnal again.

Let me know if that worked for you!

Feb 04, 2008 | Dishwashers

5 Answers

Kenmore dishwasher Lock On light flashing


holding the button for four seconds will not do it, you have to hold it until the light stops blinking and
will go back to normal, normall takes more than four seconds to unlock the unit, this is something
the sears repair techs know becouse the are trained on all this things but, they will not share this things, becouse thats how they make money

Dec 29, 2007 | Dishwashers

2 Answers

Bosch Dishwasher won't drain, cancel drain lights blink


when you said "I can run a wash", does the machine act normal for that time frame up to the point of drain? if yes, the pump is fine. sounds more like the micro chip on the board is "confused", but not sure why.

Jun 04, 2007 | Bosch 24 in. SHX99A15UC Stainless Steel...

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

612 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Owen Barnes

Level 3 Expert

867 Answers

Brad Brown

Level 3 Expert

15557 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...