Question about Clover Corporation C1704DVR

Open Question

I have the clover C-1704DVR and I can set the time, but when I record the time stays the same. It doesn't change. How do I get it to change as I am recording. Or how do I get the time to work on it?

Posted by on


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 56 Answers

SOURCE: Clover Corporation CDR4010 Video Recorder wont take my password

i dont think so

Posted on Feb 03, 2009


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Cant change the time on the alarms

Helped over 100,000 people on Fixya and never got paid Fixya are

Feb 28, 2018 | The Audio Players & Recorders

2 Answers

Does anyone have the operating manual for a Clover CW5702 ?

hi sherman.
just like you i have had a good look around the internet i can not find much.but if you want to go to this link and have a look.mind you you may have already been there.
camera operating manual for Clover CW5702 Google Search ..
if you dont have much luck have you tried ebay? sometimes you might be lucky on there.

Nov 17, 2017 | Cameras

1 Answer

I changed my settings on a technics SL -D2 as my mums old records did not play as were too dusty which I realised too late when arm and needle slid over record so I unfortunately changed settings ? Wh

First in order to work out the correct setting of the weight on the end of the arm you can look up the make of the cartridge fitted on it. This will tell you the approx weight to set it at. However most turntables need to be done by trial an adjustment, because it's a question of getting the sound right. If it was me I would set the anti-scate to the middle setting and leave it for the time being. Start with the weight. I would set it around 1.5 to start. Then try a record. If the stylus stays in the groove, you are getting close. However if it doesn't at all take it slightly towards the 2 and test again. You keep doing this till it stays in the groove, increasing only by small amounts. Make certain the test record is clean and free of any scratches as far as you can see. Also that it's not warped.
If however it not only stays in the groove at 1.5, but there's a rumble sound than take it down to 1 and test again - again only slight dowwards adjustments. It's just a question of getting a balance between staying in the groove and not getting a rumble. You might only need to adjust the anti-scate on certain records. Most should play good with it set to mid-way.
Headphones will pick up the rumble noise better if you have a problem with that, so use them to test if you can. Otherwise put the bass control to full.
Note: A bad stylus will not stay in the groove!

Jan 01, 2015 | Technics Audio Players & Recorders

1 Answer

How do I reboot my clover usa TFT LCD 2284 all in one combo security system?

Free Lifetime Technical Support Clover Electronics is based in Los Angeles County, CA. Our in-house technical support is available Monday-Friday, 8am to 5pm PST to answer your questions.
  • Toll Free: 877.327.5000
  • E-mail:

May 29, 2014 | Clover Corporation Clover Electronics...

1 Answer

Where do I get parts for a tlv1280a security vcr They sell parts for electronics and componits.

Oct 16, 2009 | Clover Corporation Clover Electronics...

1 Answer

Clover CDR 4170

u need at least a 4gb, then system search, enter the time and date u want to back up press enter, once u have it on screen put flash drive in usb, then hit the back up button.

Jan 17, 2009 | Clover Corporation CDR-4070 Video Recorder

1 Answer

I have a problem with my CDR 4170,is block with the password and i forget these,i can find my cd,

try using the channel buttons...push each button two times.
ch1 twice
ch2 twice
ch3 twice
ch4 twice

Dec 26, 2008 | Clover Corporation CDR-4070 Video Recorder

1 Answer


Theres a setting in the menu that makes it do that. I think it might be the scheduled record times that you set in it. to get back to the menu ( the smaller button next to the large round multi button), push stop and when the record light goes out (real fast)!!! push the menu button, then you should be able to change the setting in the menu...

Nov 19, 2008 | Samsung SSC DVR Digital Video Recorder...

2 Answers

Cannot view replay

It has something to do with the software and hardware as well.
But not the monitor that is trouble you.

Mar 30, 2008 | Computers & Internet

Not finding what you are looking for?
Clover Corporation C1704DVR Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Clover Corporation Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75571 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers


Level 3 Expert

80339 Answers

Are you a Clover Corporation Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides