Question about Marshall Health & Beauty

Open Question

Need to find out how to operate Marshall 85 digital blood pressure cuff

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

evwood
  • 50 Answers

SOURCE: WITH AUTOMATIC CUFF BLOOD PRESSURE MONITOR GETTING ERROR

Try different locations. The sensor must be over a vain to pick up the pulse. Locate the point on the cuff where the sensor is, and place this over the elbow. That should work. Good luck.

Posted on Feb 09, 2009

Max J
  • 22 Answers

SOURCE: WITH AUTOMATIC CUFF BLOOD PRESSURE MONITOR GETTING ERROR

E might represents insufficient inflation for your mom. For automatic inflation monitors usually there is a mechanism to keep inflating the cuff to higher pressures for people with higher BP. Check how is done. In some auto monitors,while cuff is inflated you keep pressing on START button until pressure reaches to some 15 to 20 mmHg higher than the pressure that auto usually stops and displays E.

Posted on Sep 08, 2009

DrRonJupiter
  • 10 Answers

SOURCE: mabis automaic blood pressure cuff, pressure monitor

Dear Edward: Likely, either cuff not tight enough or not in correct location on your arm or not holding device at correct height. Make sure you use Lithium Ion batteries. Try it on someone else. Dr Ron Grassi,Jupiter,Florida.USA. www.DrGrassi.com 30ad4e8.jpg

Posted on Oct 13, 2009

SEGlover
  • 1 Answer

SOURCE: Omron hem-704C blood pressure monitor show down

If your HEM 704C fell hard, it is probably the pressure transducer that is faulty, broken. To my experience it is cheaper to buy a new one then to have it repaired by a technician

Posted on Jan 19, 2010

Testimonial: "Sound advice."

  • 1 Answer

SOURCE: How do you set the time and date on a Welby Wrist

I was able to do this by 1st pushing and holding the M button and then pushing and holding the on button and holding both for 3-4 sec. Once released you will see the month flashing. change by pushing the M key to desired month then toggle to day etc with the on button

Posted on Oct 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does it mean when the blood pressure cuff reads E1


If your blood pressure mahine is like those fro Walgreen's:
Walgreen's Blood Pressure Error Readings.
Error Codes

Err 0 No pulse is detected
Err 1 Inflation rate is too low
Err 2 Systolic reading unattainable
Err 3 Cuff pressure is too high
Err 4 Diastolic pressure is outside of operation range
Err 5 Cuff deflated too fast
Err 6 Cuff deflated too slow
Err 7 Systolic pressure is outside of operation range
Err 8 Overall pressure is outside of operation range
Err 9 Cuff is unable to inflate to the necessary pressure level

Mar 31, 2017 | The Health & Beauty

2 Answers

We got a Marshall 82 digital blood pressure monitor at a garage sale, but it didn't come with the manual. And we really aren't sure how to work it????


We got a Marshall mb02 digital blood pressure monitor, but it didn't come with the manual. And we really aren't sure how to work it????

Jun 07, 2011 | Marshall Professional Aneroid...

1 Answer

Neither of the cuffs on the Homedics S18729 Ultra-Deluxe Automatic Blood Pressure Monitor work. They do not fit well around my arm and constantly slip while inflating. I don't know if it is a design flaw...


Robert, I'm not sure that the cuffs would be interchangeable. But, I suspect the problem you're having with the cuff is operator error. Speaking from experience, it's somewhat difficult at best, to apply and arm cuff to yourself. It does take some practice, but if you can get the cuff snugly in place, it should inflate properly. If you want to pursue with interchanging the cuff, contact HoMedics at 800-469-3342, to see if it's possible. Perhaps, you should get a BP Monitor that has a wrist cuff. They're a lot easier to apply and use.

Apr 01, 2011 | Walgreens By Homedics Automatic Blood...

1 Answer

Digital wrist model # SR303S, shows error 3, has new batteries


Possible explanations and work-arounds based on various blood pressure monitors..net is if it has worked religiously like mine had and this error comes up, and the simple fixes below do not work, there is something internally wrong with the unit..there does not seem to be any customer reset or obvious fixes..contact the manufacturer for service..

Error Description Potential cause and remedy

«Err 3» No pressure in the cuff
An adequate pressure cannot be generated in the cuff. A leak
may have occurred. Replace the batteries if necessary. Repeat the
measurement.

---------------------------------------
Error Codes

Err 0 No pulse is detected
Err 1 Inflation rate is too low
Err 2 Systolic reading unattainable
Err 3 Cuff pressure is too high
Err 4 Diastolic pressure is outside of operation range
Err 5 Cuff deflated too fast
Err 6 Cuff deflated too slow
Err 7 Systolic pressure is outside of operation range
Err 8 Overall pressure is outside of operation range
Err 9 Cuff is unable to inflate to the necessary pressure level
--------------------------------------
Error No. Possible cause(s)
Err 1 No pulse has been detected. Cuff may be positioned incorrectly.
Err 2 The arm was moved during the measurement.
Err 3 Inflation of the cuff took too long. The cuff is not positioned correctly.

Jan 04, 2011 | Samsung Health & Beauty

2 Answers

Walgreens HD303 Blood Pressure Monitor error 3


Possible explanations and work-arounds based on various blood pressure monitors..net is if it has worked religiously like mine had and this error comes up, and the simple fixes below do not work, there is something internally wrong with the unit..there does not seem to be any customer reset or obvious fixes..

Error Description Potential cause and remedy

«Err 3» No pressure in the cuff
An adequate pressure cannot be generated in the cuff. A leak
may have occurred. Replace the batteries if necessary. Repeat the
measurement.

---------------------------------------
Error Codes

Err 0 No pulse is detected
Err 1 Inflation rate is too low
Err 2 Systolic reading unattainable
Err 3 Cuff pressure is too high
Err 4 Diastolic pressure is outside of operation range
Err 5 Cuff deflated too fast
Err 6 Cuff deflated too slow
Err 7 Systolic pressure is outside of operation range
Err 8 Overall pressure is outside of operation range
Err 9 Cuff is unable to inflate to the necessary pressure level
--------------------------------------
Error No. Possible cause(s)
Err 1 No pulse has been detected. Cuff may be positioned incorrectly.
Err 2 The arm was moved during the measurement.
Err 3 Inflation of the cuff took too long. The cuff is not positioned correctly.

Apr 08, 2010 | Walgreens Wrist Blood Pressure Monitor

1 Answer

I have a Marshall BP monitor. My large cuff tore


Replacement cuffs are available on eBay. Here is a link to the page. [http://shop.ebay.com.au/?_from=R40&_trksid=p3907.m38.l1311&_nkw=blood+pressure+cuff&_sacat=See-All-Categories ]

Mar 30, 2010 | Marshall Health & Beauty

1 Answer

Have lost instructions for Marshll 85 Oscillometric Sphygmomanometer Electronic Digital Blood Pressure and Pulse Monitor...... is this available? #'s on box are 705203 and M 453952


I suggest you contact Omron with your requests for Marshall 80-series blood pressure monitors. Omron seem to have bought / acquired / become otherwise responsible for the Marshall brand.
That is how I got the manual for model 80 here
Owners Manual User Guide for Marshall Professional Aneroid Sphygmomanometer...
To request a manual from them send a message to them with your exct and detailed request using the webpage
Contact OMRON OMRON Global
I hope this helps
24.February.2015

Jul 10, 2009 | Marshall Health & Beauty

1 Answer

Receive error messages


Cuff too loose or too tight.

Apr 08, 2009 | Marshall Health & Beauty

Not finding what you are looking for?
Health & Beauty Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Marshall Health & Beauty Experts

Robin Hill
Robin Hill

Level 3 Expert

1263 Answers

wcdoc1953
wcdoc1953

Level 2 Expert

278 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Are you a Marshall Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...