Question about Philips 42TA648BX 42 in. LCD TV

1 Answer

My screen does not come on but it has power to it. Sometimes if I go through a cycle of cycling (unplug and plug back in) it will come back on. But not now. Any ideas?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Philips Master
  • 1,229 Answers

A bad capacitor or two will certainly make this TV act as you say. If you can remove the back cover, you may inspect and find a bulged capacitor or two. The bulge cap is a dead give away here. Replace this cap or two. The TV should fine after that. Thanks for asking and show a few hands of support!

Posted on Mar 26, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cycle selection knob has to be turned for minutes before it locks in a cycle. Machine is an LG WM2487H*M front load washing machine.


Try unplugging unit, then hold in power button for 5 seconds, then plug back in. Sometimes that resets unit. Sometimes. Good luck.

Apr 03, 2018 | LG Washing Machines

1 Answer

My machine stops in the middle of the kneading cycle. What is wrong? What can be done?


Sometimes machines have a rest period after kneading. Check your manual for process times.

Sep 19, 2017 | The Kitchen Appliances - Others

1 Answer

My screen is reading ' input is blocked ' we have no remote and now we can't watch anything. what can I do?


Have you tried to power cycle your TV? If not, try to do so and see if that works. Power cycling the TV can be done by turning it off, unplugging it, and then plugging it back in after a minute or so and powering it back on. Then restore settings back to factory defaults.

Nov 05, 2013 | Dynex 32 in. LCD Flat-Panel HDTV

1 Answer

Screen says power failure occured during cycle press start/pause to resume cycle..nothing happens


sometimes if these machines are running during power failure they get lost in thee own programmin g
this particular machine is notorious for it
unplug the amchine and let it sit for a few minutes
plug it back in and you should be good t5o go

Oct 26, 2009 | Maytag Neptune MDE5500AY Electric Dryer

1 Answer

GE PROFILE WASHER DOESN'T CYCLE TO WASH FROM FILL


  1. Clear the ERROR from the screen: Press and hold the MY CYCLES and BACK buttons simultaneously for 3 seconds. The control will display any recorded errors. Please write down what error codes are shown on your screen in case service is needed. If a MORE icon is displayed on the screen, press MORE to list additional errors. When the EXIT button appears, press EXIT.


  2. Remove Power: Follow the onscreen instructions to remove power (unplug unit) and then immediately plug unit back in.


  3. Clear Setup Mode: After power is restored, a setup screen that begins with "Congratulations..." will be shown. DO NOT PRESS the OK button shown at the bottom of the screen. Press the START/STOP and POWER buttons simultaneously until the Home Screen is displayed. Your unit is ready to function normally.

Aug 19, 2009 | GE Profile WPRE6100G Top Load Washer

1 Answer

Chi me monitor goes blank on screen save (does not come back on)


damaged power board replace it or replace the monitor

Apr 02, 2008 | Smart Modular SV3170A

1 Answer

Stops in the middle of the cycle. Now it has now power


Take it back to the scheister who sold it to you and tell him he knew when he sold it to you that it was junk. Why doyou think he wasgetting rid of it? These machines are garbage. The Edsel's of washing machines

Jan 12, 2008 | Whirlpool Calypso GVW9959K Top Load Washer

1 Answer

Whirlpool Electric dryer E1


An E1 Code is a thermistor fault TEST #3a Thermistor Test
The machine control electronics monitors the
exhaust temperature using the thermistor, and
cycles the heater relay on and off to maintain
the desired temperature.
Begin with an empty dryer and a clean lint
screen.
1. Plug in dryer or reconnect power.
2. Set the following configuration:
➔ Door – must be firmly closed
➔ Press Control On
➔ Press End Of Cycle Signal (Louder)
➔ Press Start
3. If after 60 seconds, E1 or E2 flashes in the
display and the dryer shuts off, the thermistor
or wire harness is either shorted or open.
➔ Unplug dryer or disconnect power
➔ Check wire connections at the machine
control electronics and thermistor.
To access the Thermistor you will need to open the bottom front panel 2 screws the thermistor is on the exh duct (Center) check it there let me know if you need futher help

Dec 09, 2007 | Whirlpool GEW9250 Electric Dryer

1 Answer

Whirlpool Duet Electric Dryer (5yrs old)


An E1 Code is a thermistor fault TEST #3a Thermistor Test
The machine control electronics monitors the
exhaust temperature using the thermistor, and
cycles the heater relay on and off to maintain
the desired temperature.
Begin with an empty dryer and a clean lint
screen.
1. Plug in dryer or reconnect power.
2. Set the following configuration:
➔ Door – must be firmly closed
➔ Press Control On
➔ Press End Of Cycle Signal (Louder)
➔ Press Start
3. If after 60 seconds, E1 or E2 flashes in the
display and the dryer shuts off, the thermistor
or wire harness is either shorted or open.
➔ Unplug dryer or disconnect power
➔ Check wire connections at the machine
control electronics and thermistor.
To access the Thermistor you will need to open the bottom front panel 2 screws the thermistor is on the exh duct (Center) check it there let me know if you need futher help

Nov 10, 2007 | Whirlpool GEW9250 Electric Dryer

Not finding what you are looking for?
Philips 42TA648BX 42 in. LCD TV Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75581 Answers

matt martin
matt martin

Level 3 Expert

1229 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Philips Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...