Question about Washing Machines

1 Answer

I need to replace a belt on a kenmore 60 series washer. What exactly do I need to remove to replace it so I want remove things I shouldn't?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 97 Answers

Hiya
the belt should be the only thing that needs replaced, no other parts will need to be taken off.

hope this helps


please dont forget to rate the helpfulness of this reply thanks kj

Posted on Aug 03, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am having trouble replacing my belt on my Kenmore 70 series


i've got them down to 10 minutes, but here goes. remove the bolts going into pump, but do not remove pump . remove the transmission bolt with the spacer and this is where you push the belt through and around pulleys.. this is a little more difficult. you will need to take off the yoke spring and move the transmission pulley around until the spin control magnet catches for spin. it will begin to take pressure off of clutch. you will need a long screwdriver or something like it to apply pressure down on the clutch plate this is to allow to to slip the belt thru the bar the spring came off of and under it.. you can then pull the belts around all pulleys and put everthing back in its place and your done...

Jul 18, 2009 | Kenmore Washing Machines

1 Answer

Kenmore 60 series does not agitate


Dear chrissharter,

Probably just a broken belt!
Open it up and see!
Replacing can be a pain but belt cost is probably under $20 at appliance parts store near you in Phone Book.
Replacing is just removing nuts & bolts and moving brackets
Before you take it apart look carefully at where the new belt will go!
If you have someone do it for you it should cost a lot less if you know it's the belt & you have it all apart!
I have to go to my regular job now but if you need detailed instructions you may want to go for FixYas' Guaranteed Solution!

Good Luck!
jackiaria
6d66146.jpg Hope This Will FixYa!!! Please Rate Me!!!

Feb 01, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Kenmore 70 series washer quit on me


this sounds like an old belt drive whirlpool washer, probally a problem with the wig wag or the tranny, maybe, nee more info

Jan 29, 2009 | Kenmore 22422 Top Load Washer

1 Answer

Kenmore 70 series washer will not spin, clothes are too wet


Not a belt, this is only a sound deadening devise on the brake housing. Not really needed. Replace the coupler

Jan 03, 2009 | Kenmore 24032\24036 Top Load Washer

1 Answer

Kenmore 60 series will not drain


Well if this is a belt driven model then your solenoid coil is bad.
This model 's motor only revolves in one direction. To spin it has to shift gears. It does this by means of a solenoid mounted on the transmission called a wigwag. Note: if the lid switch is bad no power can go to the wigwag and shift it. If this is a direct drive model(no belt) then it has to be a bad lid switch.

Dec 28, 2008 | Kenmore 24032\24036 Top Load Washer

1 Answer

Can't get replacement parts back on Kenmore 60 series dryer.


The belt has groves, right? Make sure the groves go over the motor pulley from the right. The idler pulley is spring loaded. Place the belt around the idling pulley with the smooth side of the belt on the pulley. This should work.

Dec 24, 2008 | Kenmore 62602 Electric Dryer

1 Answer

Kenmore washer 60 series


Hi, thanks for using the FixYa service. Your lid switch is probably broken. Make sure you can hear it click when you open and close the lid. It it is a very common problem on that model. Probably has nothing to do with the pillows, that was just the last load in the machine before the common part failure. Get me the exact model number and I can get you the replacement part number.

Dec 19, 2008 | Kenmore 24032\24036 Top Load Washer

1 Answer

Kenmore Washer Top Load Series 60 won't drain


The water pump is a belt-driven device actuated by a clutch. Your problem could be:

1. Stuck pulley - break it loose and WD-40 it
2. Broken belt - replace
3. Bad clutch - call repair or replace

There is almost nothing that can go wrong in the pump itself. It's probably one of these three.

Dec 16, 2008 | Kenmore 24032\24036 Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

yadayada
yadayada

Level 3 Expert

66563 Answers

Brad Brown

Level 3 Expert

14405 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...