Question about Computers & Internet

Open Question

Model#ICO14C,can not get it to work n can not adjust picture

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
gcsltd
  • 239 Answers

SOURCE: The sound won't work on

pls go to control panel \ sounds & audio devices \ audio devices n configure.. Confirm if ur default devices are well set for recording etc...

u can also hv a look @ voice tab if prob persists

Posted on Feb 05, 2010

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

VERTICAL LINES ON OLDER ZENITH FLOOR MODEL TV


this was adjusted by the fine tune on the selector It is the picture not being held in place by being out of tune Same as if the picture goes sideways On the real old units there were 2 knobs to make these adjustments.

Jun 10, 2013 | Televison & Video

1 Answer

I need to know how to adjust the picture on rca proscan tv model PS31122


Adjust via the menu in the set, this is an older model and pretty easy to work with.

Let me know if you have some issue or problem

Mar 15, 2012 | Televison & Video

1 Answer

Both the picture and sound work when the TV is turned on, yet the picture is distorted like a double picture and has a yellow hue to it.


Sounds like you have a convergence problem. If you go into the setup menu of your TV, there should be some settings to adjust the red, green and blue hues and re-position them so each color matches up. If this does not work or if you don't have a menu, your TV *might* have a circuit board with several plastic screws on it. These adjust the picture and it's a very tedious task to re-align each hue correctly.

My projection TV is an older model from 1995, which is probably why it has this circuit board in place of a convergence menu built into the TV.

If adjusting the convergence still doesn't work, you might need to purchase a new convergence chip.

May 20, 2011 | Sony KP-51WS520 51" Rear Projection...

1 Answer

I have a Vizio 55" TV model M55ONV. I can't


Are you using a cable box like a DVR?...there should be a setting on that for aspect ratio, not sure this is a TV issue

Dec 18, 2017 | Televison & Video

1 Answer

The sound won't work on my web cam model # ico14c


pls go to control panel \ sounds & audio devices \ audio devices n configure.. Confirm if ur default devices are well set for recording etc...

u can also hv a look @ voice tab if prob persists

Feb 02, 2010 | Computers & Internet

3 Answers

Enet pc camera driver i needed


Enet pc camera driver i needed button1-share.gif hi i nedd this driver i have it in a minidisck but will not play maybe you can help!!!!!!!!!!!!!!!!!!

Jun 16, 2008 | Computers & Internet

1 Answer

Problem with the color on my TV


I will need to know what make and model your tv is.

Feb 16, 2008 | Televison & Video

1 Answer

GE model 31GT660


Is the brightness in the middle of adjust range? Is the picture
or contrast adjust at 3/4 ? Next,adjust the screen voltage on
lower rear of cabinet = one control is focus and one is screen..
how is the picture now ?..........................T.

Feb 11, 2008 | GE 31GT660 TV

1 Answer

46 inch rear projection tv bulb replacement model number 46gw944


1) In customer menu, adjust all video controls to center,then
increase "picture" to 3/4
2)Locate focus/screen adjust block above chassis...adjust
RGB screen controls for best mixture = B/W tracking..
Check with customer color level at minimum..should look gray.
If you turn screen controls up too much,you will see faint
re-trace lines in picture.....once B/W looks good,put color level
back to middle...................................................T.

Feb 05, 2008 | Televison & Video

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18424 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

David Payne
David Payne

Level 3 Expert

14162 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...