Question about Televison & Video

1 Answer

My hitachi 50inch plasma has been dogged with problems,it now turns itself off without any screen and reverts to standby after only a few seconds.i had this problem previously and the repairers under warranty replaced the Y-Sustain board .can i assume this will fix the problem again or can it maybe something else

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 158 Answers

Have the whole unit replaced if you are still in warranty surely they will agree if they see it on your service record. talk to a supervisor if you have to.

Posted on Mar 24, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Hitachi Ultravisio 50inch plasma TV. I was watch it when all of the sudden the screen went black. The TV did not turn off. What is the problem and can I fix it reasonably?


Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/ In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.

Mar 24, 2017 | Hitachi Televison & Video

1 Answer

I have a Soniq 50inch plasma, the picture has turned very red. It has happened in the past, normaly I just turn it off for a few minutes and it goes away, but it has been 2 days now and it hasn't


plama tvs do this often after you have it for a while. there is no salution but to buy a new tv. this happened to my dad's friend and he said you cant fix it you just have to buy a new one. he akso said his next tv wont be a plasma of ant type!

Jun 05, 2012 | Televison & Video

1 Answer

My hitachi plasma screen turns off after a few seconds and has a blinking red standby light.


I suspect that your power controller board has a problem and is causing the shutdown. If it is under warranty, get it fixed under warranty. If it is not, it may be possible to purchase the board and install it your self. Be careful though plasma TVs have some areas to avoid when servicing.

Feb 13, 2012 | Hitachi P42H401 42 in. Plasma HDTV

1 Answer

My hitachi plasma tv model: p55t551 every time i


turn tv on the red power light comes on then goes off again

Jun 27, 2010 | Televison & Video

1 Answer

Hitachi Plasma Model PD32-A3000/AVC-A3000


vertical red line on screen - I have a Hitachi plasma 42HDs69

Jul 29, 2008 | Hitachi 42HDS69 42 in. Plasma Television

2 Answers

Plasma wnt stay on


I have had this problem in some models of plasma sets before. In most cases the power supply and main drive boards had to be replaced. In a small number of cases the failure was the screen itself.

In all cases, the cost of the repair was expensive. For the screen failure, the set was scrapped.

Jerry G.

Dec 30, 2007 | Hyundai ImageQuest HP4240 42 in. Plasma...

1 Answer

GE 31GT740 clicks off and on


Dead, led flashing red/green at first, then going to red standby
Replace C604 (1000uF, 16v) elec. cap. It is in the decoupling circuit for the 5 volt supply
Reverts to standby from switch on via TV or Video
No 5v rail because FET MTP3055 o/c. (BUZ71 will do nicely)
Goes straight to standby, after a quick burst of power
Replaced R952 (39K), had gone slightly high

Nov 23, 2007 | GE 31GT740 31" TV

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74106 Answers

Cindy Wells

Level 3 Expert

5096 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...