Question about Toro Lawnmower 20099 Mower Mowers Lawn

1 Answer

Limited self propell - Toro Lawnmower 20099 Mower Mowers Lawn

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 111 Answers

The self propel cable needs to be adjusted. This can be done with a 7/16 wrench. loosen the nut that holds the self propel cable in place. You may need to pry this open with a screwdriver. Don't overdo it or you could break the plastic. Once the cable is loose pull it toward the mower deck, once the slack is out of the cable press the self propel handle in about a half of an inch. This should be close to what it was from the factory. Then re tighten the nut. And check the self propel to make sure it is engaging properly. If you hear a grinding noise when trying to engage the transmission then you will need a new transmission. Depending on if it is a front or rear self propel the part alone is either $60-$75 retail. Most repair shops will charge an hour to do this repair. I hope this answers your question.

Posted on Apr 05, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have the Hoover, self propelled vacuum. I have only used the self propel function a few times, but our babysitter used the feature and now the vacuum only works on the highest carpet setting. The middle...


Move the carpet height control switch to a higher position if the vacuum is difficult to push. If the setting is too low for the carpet being cleaned, the brushes press against the floor preventing the vacuum from moving easily.Set to a medium-high height setting then check.Slide the "Self-Propel" button to the "ON" position if the cleaner does not self-propel. -----------
The self-propel feature operates only when the cleaner switch and the self propel button are both ON. ---------- Try this settings and check.This should help.Thanks.Helpmech.

Jun 24, 2011 | Hoover Self-Propelled WindTunnel Bagless...

2 Answers

I have a Toro self propelled walk behind mower model # 20016. The self propelled just stopped working. My owners manual does not mention anything about the self propell. Can you direct me as to what to...


Toro 20016 self propelled walk behind when the wheels are engaged it moves, when the wheels are not engaged, the wheels look up.
What should I do to fix the problem

Apr 19, 2011 | Toro Lawn Boy Self Propelled CARB Walk...

1 Answer

My 625 self propelled will start as long as i am using the prime button, when i stop priming the carb. it will stop


I suspect your primer bulb has a pin hole in it and is sucking air thus limiting the fuel to the carb.

Mar 30, 2010 | Poulan Pro 22" Self Propelled High Wheel...

2 Answers

Self Propel doesn't work on Hoover Wind Tunnel


Your self propel wire could be broken. Lean the vacuum back like you were using it. If you stand in front of the vacuum look down and to your left. When you move the selp propel button you should see a wire move. If not then it's broken.

Oct 06, 2009 | Hoover Self-Propelled WindTunnel Bagless...

1 Answer

Self-propelled feature does not work at all! Any suggestions?


You might have a broken belt to the self propelled or a broken spring or whatever engages the self propel. Take off the cover and see if anything is broken or missing. Have someone engage the self propel while you are watching and see what is going on.

roundo4

Aug 12, 2009 | Toro Lawn Mower With Toro Power Tools

1 Answer

Self Propelled mower quit self propelling


you probaly have a broken gear or engagment lever. the part the cable goes through before the cable goes thru the deck. you also could have sheared a pin or the plastic gear that drives it.

Jul 02, 2009 | Troy Bilt 5.5hp Self Propelled Mower

3 Answers

Self propell toro mower will not "self propell."


Self propell toro mower will not "self propell", nor can i pull it backwards

Oct 03, 2008 | Toro Lawn Mower With Toro Power Tools

Not finding what you are looking for?
Toro Lawnmower 20099 Mower Mowers Lawn Logo

497 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toro Garden Experts

Joseph Mueller
Joseph Mueller

Level 2 Expert

338 Answers

Mike Squire

Level 2 Expert

391 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Are you a Toro Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...