Question about Robot Coupe MMP 170 VV 220 Watts Hand Mixer

2 Answers

I need to open the handle because I have a loose contact in the power cable. can you tell me how or where can I find the service manual Thanks

Posted by on

  • 2 more comments 
  • dsalasq Mar 24, 2011

    The thing is that to be able to replace the cord, I'll need to unassamble the machine

  • dsalasq Mar 24, 2011

    Hello, your "sugestions" did not help at all. pls refund what you have charge to my credit card


  • dsalasq Mar 24, 2011

    Those sites were the ones I found before contacting you.
    Pls credit back the amount charge. I'll have to take the unit t service

  • dsalasq Mar 25, 2011

    No solution provided. pls credit the amount charged. Thanks



2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 1,998 Answers

Try this link and message me back if this works for you this company doesnt seem to want anyone else working on there product for some reason if there not authorized you can also check this site as well for further diagrams on this unit as well sheesh come on now its only a mixer if you have any further questions message me back and please remember to rank how this opinion has helped when our chat has fully concluded Thanks

Posted on Mar 24, 2011

  • 1 more comment 
  • Rick Ead
    Rick Ead Mar 24, 2011

    firstly you wouldnt talk to me about refunding your credit card secondly if this did not help then you could simply message me back and i would look further into exactly what you are looking for this is a chat typed situation where we go back and forth until you are satified with the outcome of your questions the diagrams do show you how to take the handle apart if you are looking for more information on this then you would simply ask and i could look further into the problem. i will personally contact the company that makes this unit and reply after i have conversed with them Thank you Rick

    p.s you asked in your original post you need to open the handle because I have a loose contact in the power cable these diagrams even show the screws that you have to remove in order to acess where the plug goes into the unit please state exactly what you are looking for instead of makeing short vague comments on what will help you in your situation if your looking for a complete service manual to this unit very sorry but they dont make one for the public to view fi you would like to contact robot coupe about this further to reach there customer support you would click here and then you would also be able to send your unit back to them to have them repair the unit this is how they want it done at this company and by following there procedures is about the best way to get your unit fixed Thanks again Rick

  • Rick Ead
    Rick Ead Mar 24, 2011

    I have sent them a personal message requesting the service manual from them and i am awaiting there reply Thank you Rick

  • Rick Ead
    Rick Ead Mar 25, 2011

    there is a solution provided as to the diagrams provided which is what you asked for in your oringal post lastly i have also contacted directly to robotcoupe on the matter of your service manual So you can choose to wait for them to respond to my contacting them or you can continue acting in your rude state. you obviously havent read what i wrote in my previous reply so maybe we can just chalk this one up to an illiteracy issue that you are having atm have a great day Rick


  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 12,061 Answers

Hi, I have looked for a service manual, but cannot seem to find one.
However these are not that complicated, and if you are simply going to replace the cord, then i think you should be Ok without one?
Just open it up, and get a replacement cord, and reattach it exactly as it comes off, I think you will be Ok.
As you will see when you get inside there is not too much to them.

Posted on Mar 24, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

KSM88PSQGC0 won't turn on

There are a few things that may cause this. In no particular order they are:

1. No power at electric outlet.
2. Brush(es) worn out.
3. Switch on control board not making contact or speed link broken.
4. Mixer's power cord faulty.
5. Connection to control board not making contact.
6. Field coil or armature faulty.
7. Highly unlikely -- contact to a brush sleeve has slipped out.

The Service Manual for your machine can be found at:

Feb 18, 2017 | KitchenAid Food Mixers

1 Answer

Hi. How can we contact your office. We need to service our hobart 200 in makati. thanks

Prospect around on the Hobart service page for Customer Support contact options:

Dec 29, 2014 | Hobart A200 Stand Mixer

1 Answer

My kitchenaid professional mixer will not run.

The Service Manual for your mixer can be found at:

Among the causes for the mixer not turning on are (in no particular order) --

The leaf-spring switch on the Control Plate is not making contact.
The Phase Board is defective.
Brushes need replacement.
Brush chamfered side not correctly oriented.
Bad armature or field coil.
Seized motor bearing.
Detached or broken Control Board spring.
Speed Control Link plastic end broken.

Jun 01, 2014 | KitchenAid KSM90 Ultra Power Series Stand...

1 Answer

Broken wire - Kenwood A701A

black wire indicates negative so if you can see a place on the circuit board that looks like that's were it came from then get some advice from an electronics person before you put it together.

Jan 27, 2014 | Kenwood Food Mixers

1 Answer

Head Lift Lever retaining spring fitting ?

Request the service manual by contacting Kenwood directly.

Dec 20, 2017 | Kenwood Food Mixers

1 Answer

Top part of mixer is bouncing when in use.

Hi and welcome to FixYa, I am Kelly.
The Head Lock is most likely worn. The 4.2 mb Service m\Manual is located here:

You may have a worn hinge pin: Figure 7 page 7 of the pdf file.
The spring for the head lock can be also broken. Item 20 this link:

See page 22, figure 72 in section 5 of the service manual for pedestal hinge repairs. Most likely the set screw for the head lock has come loose.

Your parts can be found here: (with some exceptions like item 20 above)

This information should get you going if your able to read the manual and follow the sometimes vague instructions.

Thanks for choosing FixYa,

Jan 02, 2011 | KitchenAid KSM90 Ultra Power Series Stand...

1 Answer

The mixer motor starts and stops, it will not continue running on any speed. By playing with the speed selector you can get it running sometimes but you cannot keep it running if you change speeds.

Here is how your speed control works:

Speed Control
The speed control of the mixer is attained through the use of a governor assembly mounted at the rear of the control plate assembly.
The electrical circuit is made and broken by the action of the fly ball governor revolving against the control plate.
When the switch lever is moved to an ON position, the position of the control plate with respect to the governor is changed by the action of the switch lever.
Thus, when the control plate is set close to the governor, a relatively low speed of the motor causes the governor to make or break the mixer’s electrical circuit through the control plate.
When the control plate is set farther away, a greater motor speed is required before the governor starts breaking the circuit.
The action of the governor is such that the speed of the motor will remain constant for a given setting of the control plate within certain loads.
After certain loads have been exceeded, the speed of the motor will drop to meet the torque requirements of the given load.
Speed is controlled by the governor and the control plate in conjunction with the phase control.

NOTE: The triac regulates the power the motor sees depending on control board contacts.
A device called a triac is a part of the phase control circuit.
This device determines the amount of power the motor sees dependent upon the condition of the control board contacts.
If both contacts are open, about 40 volts RMS is applied to the motor and about 80 volts is applied when either contact is closed and the other is open.
When both contacts are closed, the triac is full on; consequently, full power is applied to the motor. In this way, the speed is controlled.
If the mixer motor begins to run too fast for a
particular speed setting, one or both contacts open, which cuts back on the voltage the motor sees, thus slowing it up.
If the motor operation becomes too slow, one or both contacts will close, applying the needed voltage to the motor to sufficiently increase motor speed.
This is always accomplished through the triac.
The control plate contacts control the triac, and in turn, controls the amount of power supplied to the motor.

The control Plate for your mixer is PN

If your not good with tools / meters or tedious repairs do NOT attempt this yourself.
The service manual for your mixer can be found here

and is:

Mar 14, 2010 | KitchenAid KSM103 Professional 5 Series...

22 Answers

Kenwood A701a service manual

Hi I'd really appreciate a service manual please?!

Sep 29, 2009 | Kenwood Food Mixers

1 Answer

Help? I need the Shop Manual for a Hobart A200 mixer. Thanks.

Ricardok45,I'm a hobart tech and can tell you nobody has ever bought hobart,they are a subsidary of illinois tool works.It's true hobart doesnt release any of their service manuals to the general public,however if you need guidence or parts i can help you.

Jan 15, 2009 | Hobart A200 Stand Mixer

1 Answer

Biggt----can you help? A200

What is your symptom?

Basically, you need to check both start and run windings for continuity.

If you have a mechanical start switch, (likely), you can simply ohm out at the power cord end, hot to neutral, power switch on, and check for continuity. Then manually open the contacts on the start switch and look for a small increase in your ohms. I don't know the exact numbers, but I would expect under 10 ohms.

Apr 16, 2008 | Hobart A200 Stand Mixer

Not finding what you are looking for?
Robot Coupe MMP 170 VV 220 Watts Hand Mixer Logo

Related Topics:

333 people viewed this question

Ask a Question

Usually answered in minutes!

Top Robot Coupe Food Mixers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Oscar Netto
Oscar Netto

Level 2 Expert

110 Answers


Level 3 Expert

80637 Answers

Are you a Robot Coupe Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides