Question about Vizio E370VL 37 in. LCD HDTV

1 Answer

My wife was messing around with our 1056B01-L Conway Corporation cable remote attempting to change inputs and our Vizio E370VL TV showed a message that said "input lock" and then immediately shut down. Now it will only come on for a few seconds, show the VIZIO screen, and then turns itself off. Are there any quick fixes for this or can this TV be reset? I have tried turning off and then turning back on, unplugging and then holding the power button, holding down the input button and then turning on the TV and none of these have worked.

Posted by on

  • Irwin Louie Jan 17, 2013

    I have the same problem as well. Will follow with hopes that a solution will be offered

  • C. Somerville Feb 18, 2013

    Same thing has happened to our tv also. A visiting friend was messing w/ the cable remote & now it only comes on for a few seconds, shows the Vizio screen, and then shuts off. Did you find a solution?

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Have you had any luck? It just happened to me now!

Posted on Jul 04, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Technician can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Technician (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tv does not respond to any input only shows nosignal to any device


Did the TV's source get changed? If you use the Television remote and find the source or input button which switches between the video sources for your TV such as HDMI, A/V, Television Tuner,, VGA connector or Component video. If your using a cable box that remote only controls the cable box and possibly the TV power and volume but the cable box remote does not change the source input of the TV. Most Cable boxes rebroadcast their video on a specific TV channel and your TV must be set to that channel to receive the signal from the cable box. Let me know if this helps you out.

Aug 20, 2014 | Televison & Video

1 Answer

Vizio VO370M red color has gone away


Change the input to some other device and see. Then if the problem persists, this might need attention by a qualified service technician.

Jul 25, 2012 | Vizio E370VL 37 in. LCD HDTV

1 Answer

Vizio e370vl 37" LCD TV powers off by itself. It comes on, displays Vizio logo white, then turns off and goes to yellow. We tried unplugging everything for 5mins. Tried changing inputs, no RGB cable c


Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Pull up older posts.
http://electronicshelponline.blogspot.com/
In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.

Dec 25, 2017 | Vizio E370VL 37 in. LCD HDTV

1 Answer

Where to hook up my dvd player


U look around on the back of ur tv or the side of the tv u see a 3 holes one YELLOW,one RED, one WHITE hole all lable INPUT in a straight in a role that for hook up to the tv if u are using a RCA component cable Y-Video,R-Audio,White-Audio.The other end of the RCA component cable Y,R,W go into DVD player 3 holes Y,R,W OUTPUT holes.

Aug 27, 2011 | Vizio E370VL 37 in. LCD HDTV

1 Answer

Have new E370VL hooked up to Dish Network via coax. The picture jumps/blips? Connections are tight. Help.


This can happen when there is radio interference near the coaxial cables. Sometimes the interference is behind walls. The solution is to try a different combination of modulation and channel than what the DISH receiver is current set.

The DISH menu screen for this setting is Menu-6-1-5. With dual-tuner receivers, typically "TV 1 Out" is the TV that is connected in the same room as the receiver is located. "TV 2 Out" is the tuner that is fed to the remote TV via backfed coaxial signal.

All that needs to be done is to change the channel and mode going to the effected TV to something different. If your channel/mode is currently set to Air/60, try changing it to Cable/73. When you change the mode/channel in the DISH receiver, you need to set the remote TV to the same mode and channel.

Keep in mind that with some TV companies like VIZIO, they call their "Air" mode "Antenna". With VIZIO's the TV must be set on TV input and then go into the Menu to the Settings, Tuner Settings. Change mode type to match what you are trying on the DISH receiver, exit the VIZIO menu and manually enter the channel number.

Eventually with trial and error, you will find a mode/channel combination that isn't effected by your particular environmental interference.

Jan 03, 2011 | Televison & Video

3 Answers

I cant see anything on my vizio 32 inch television


I just spent an hour trying to fix the VIZIO with the same problem. The screen had no picture at all, but could hear the sound perfectly!! But we i figured out the solution! UNPLUG THE CABLE BOX AND LET IT RE-BOOT! and it WORKED!!!!!

Aug 05, 2007 | Vizio L32 32 in. LCD HDTV

Not finding what you are looking for?
Vizio E370VL 37 in. LCD HDTV Logo

633 people viewed this question

Ask a Question

Usually answered in minutes!

Top Vizio Televison & Video Experts

The Knight
The Knight

Level 3 Expert

74887 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Computer Repairing
Computer Repairing

Level 3 Expert

14641 Answers

Are you a Vizio Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...