Question about Washing Machines

2 Answers

Simpson washing machine encore 756 displays error df and will not complete cycle

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Our simpson encore 756 flashes SP can anyone tell us what it means and how do we fix it thanks mark

Posted on Jun 18, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The sp stands for start and pause

Posted on Mar 19, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My washing machine goes fine until half way through wash then comes up with error code PU and beeps until I turn it off...will not drain out the water? Simpson encore 556


simpson encore pu Unsolved Problems - Fixya

www.fixya.com/unsolved_problems/simpson_encore_pu
Unsolved problems for simpson encore pu question. Get free help ... My simpson encore 757 shows PU error code. What is this? ... Simpson encore 556. Aug 22 ...

Sep 10, 2015 | Simpson Washing Machines

1 Answer

Why is there an 'SF' code showing and continuous beeping from our Simpson encore 756


there are different sf codes for different faults. try googling the sf number fault to find problem.

May 25, 2014 | Washing Machines

1 Answer

Simpson encore 605


Sounds like a motor transmission problem.190.00 parts and labor is not a bad price.
Check if there is a warranty with the new parts the service person is installing.

Oct 27, 2011 | Washing Machines

1 Answer

SIMPSON 816 ENCORE WASHING MACHINE ERROR MESSAGE


Hello

Try running the washer through rinse/spin cycle,then normal cycle without any detergent.

SF is suds failure,or too much detergent or wrong type of detergent.You need to use H E type detergent.

This should clear the machine out.

Apr 01, 2011 | Electrolux Washing Machines

1 Answer

Simpson encore 756 flashes sf


Motor overloaded wait 15 minutes, press start stop.

Oct 04, 2010 | Washing Machines

1 Answer

Simpson encore 605 wash machine 6kg. Washer pump


Hi mark just read your posting.Now what country do you live in.If you live in Australia then I can give you some phone numbers.Regarding your machine it does sound like the control board.Probably the power supply section of the board is faulting.Please reply with additional information and I can help you further.

Jun 19, 2010 | Washing Machines

1 Answer

I have a Simpson encore 807 & screen displays DF what does that mean? It Still washes ok Beeps a lot though? can anyone help


The clue is in the water temp. light flashing. DF means that the temperature sensor is faulty. Replace it with a new one. Turn power off at wall. Remove the 3 screws & open panel. Sensor is plugged onto control board near the middle top of board & goes down into the base of the control panel at the middle where the water enters the machine. Unplug from the board taking care not to damage the pins on the board. Replace the new one making sure the o-ring is on it. Close up panel & turn power back on. All fixed!

Please rate my help++++Thanks for using FIXYA

May 19, 2010 | Washing Machines

1 Answer

Says sf on screen Simpson encore 807


i have a Simpson encore 807 & its displays DF what does that mean... as it keeps beeping...

Jun 30, 2009 | Washing Machines

2 Answers

Simpson encore 806 washing machine beeping and screen showing DF


DF means the temperature sensor is faulty. Replace it. Get a new one from your Simpson agent. Turn power off. Open panel by removing the 3 screws at the rear of panel & swing it up. If you are standing behind the machine look on the left hand side at the top of the circuit board. You will see a small white plug with 3 wires (red-white-black) Very carefully pull this plug toward you off the 3 pin base. The other end is the sensor pushed into the water inlet chamber. Pull it out. Push new sensor into water chamber (make sure black rubber o-ring is on it) Push wiring plug back onto 3 pin base. It can only go on one way. Do not force it or twist it as the 3 pins can be easily broken or damaged. Then close panel & power up.

Jan 11, 2009 | Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

1,102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...