Question about Washing Machines

2 Answers

I have a bush wd 1000 txve with error code unb and wont spin. What does this mean?

Posted by Anonymous on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 6,277 Answers

Hi from retired Englishman in SW France,
'unb' is likely to stand for 'unbalanced' and spinning shows any problem with balance the most!
It is necessary to ensure absolutely that the machine, even when empty, has all 4 feet very firmly on the floor, and I mean firmly ;-0)
Doesn't matter whether it is empty or not but switch it off then-
very firmly push one front corner diagonally into the centre of the machine and see if the machine moves or rocks AT ALL, even the slightest. If it does you will need the open-ended spanner which came with the (new) machine........which of course went missing a long time ago?!! An adjustable spanner will suffice.
Adjust the foot under that corner downwards until it is very firmly- almost pushing- against the floor but not so far that the corner lifts up!
If this corner did not rock do the same to the other.
Once you cannot rock the machine the slightest little bit, screw the locking nuts up tight to the underside of the machine so that they will not move. Ideally the rear feet should also be locked.

If this has not cured the problem it is possible that the internal suspension is malfunctioning.

Good luck,

John C

Posted on Mar 22, 2011

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

UNB means unblock on this machine. Remove the filter located at the front of machine bottom right as you are looking at it. Put a towel on the floor first as some water will run out. The filter unscrews, instructions should be on the inside of the cover. Make sure it is all cleaned inside. If the filter appears clean, check inside the housing for such things as a coin or other small metal object that might be jammed inside causing the contacts to read as blocked. I found a pound coin causing mine to error.

Posted on Mar 26, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an error code e7-02


Does the copier make a load noise like a jet engine starting up???? A E7 means the laser polygon mirror motor is not spinning at the correct speed. The only way to clear the code is to replace the whole laser unit or just the polygon motor... If you fell luck.... you can spray a small amount of WD-40 in the bushing of the motor > it is just a band aid... it will come back.... Good Luck

Nov 08, 2011 | Sharp AR-275 Copier

2 Answers

I have a samsung washing machine wf7600naw washing machine that won't spin and is displaying the error code SE. How can I fix the problem?


WATER DRAIN ERROR - Display shows 5E.

5E is displayed if the water level frequency detected is 25 KHz or less in the initial phase of the UNB -detecting cycle. The Water Drain error can be cleared by turning POWER SW OFF and back ON.

Dec 11, 2010 | Samsung Washing Machines

1 Answer

Error code Unb: After the last rinse finishes, spinning fails completely due to unbalanced of the laundry (What does this mean) and How do I clear the error. Machine does not spin the clothes.Every thing...


I have had the same problem with the same model and rang up the help line to be told that the machine cannot sense the clothes in the drum. I tilted the machine forward and this worked for a while, sometimes i have to unplug at the wall so there is no electricity flowing through the machine for an hour and it resets itself,. Its not adequate but it works.

Sep 02, 2010 | Haier Washing Machines

1 Answer

I have a bush wd 1000 txve washer drier and the drier wont work keeps coming up with e13


Hello,the E-13 error code is a drain timeout code. This means the pump has run a certain amount of time without fully draining itself. This could be anything from a clogged drain line in your home to a clogged drain line in the machine, your pump is clogged, pump is burned up, no power to the pump, bad board etc. Most of the time its either something jammed in the pump, or its burned up (from something being jammed in it). Just have to take her apart to find out for sure.

Thanks

Jun 01, 2010 | Washing Machines

1 Answer

Spin cycle error - UNB


Haier have had one or two problems with there spin,
option 1 make sure the machine is balanced perfect [no rocking at all ] use a level on the machine [ truly ] it works.
option 2 you can not wash one item [ underload the machine or overload the machine this will give same result UNB .
option 3 if you have had the machine a few months and this has just started [ clean the armature on the motor with emery cloth and a quick spray of W D 40 please plug out the machine first
0161 355 8254 if you need help , good luck

Feb 17, 2009 | Haier HWD1000

1 Answer

Mitsubishi WD-62528 error code 45


go to the manufacture site they should tell you what the code means if not try techlore.com

Feb 01, 2009 | Mitsubishi WD-62525 62" Rear Projection...

1 Answer

Spinning but clothes are still very wet ,


unb means unbalanced i had the same problem and i called comet where i got it from and they replaced the chip board and ever since then its been fine i hope this helps you

Jan 27, 2009 | Haier XQG50-QF80 Front Load Washer

2 Answers

I have the HAIER HW-C1260TVE-U washing machine, and for some reason it won't do the spin cycle? at the end of the programme in says something like "UNB END". Any ideas?


Hi Mate;

Just had the exact same problem with the spin cylec and now its stopped completely, I was getting ERR 7 on the display, its telling you that there is something wrong with the motor.checked the motor and found that one of the Carbon Brushes was sticking/Stuck, Just 2 phillips head screws and the carbon brush is out, mine had a bit of melted plastic/casing snagging the Carbon brush, i just jusd a bit of fine sand paper to clean the Brush, put it all back together and lo and behold everyting works.
Hope this helps

Listed below are all the error codes:

Display messages:
Err1: Error message. Door is not properly shut 20s after program is started.
Correction: Shut the door properly.
Err2: Error message. Drainage error, water not emptied within 4 min.
Correction: Clean the filter and check the drain hose for blockage. If error still exists, please contact the maintenance personnel.
Err3: Error message. Temperature sensor is not properly connected or damaged (display at the end of a program).
Correction: Contact the maintenance personnel.
Err4: Error message. The heater may be broken or the desired temperature is not met within the specified time due to an overloaded laundry (display at the end of a program).
Correction: Reduce the load and restart, or contact the maintenance personnel.
Err5: Error message. The required water level is not reached within 10 min, or the water level exceeds the protection value.
Correction: Check to see if the tap is turned on and the water pressure is correct. If error still exists, contact the maintenance personnel.
Err6: Error message. Motor speed error. It may be not properly connected or damaged.
Correction: Contact the maintenance personnel.
Err7: Error message. Motor overheat protection or is damaged.
Correction: Contact the maintenance personnel.
Err8: Error message. Water level exceeds protection value.
Correction: Contact the maintenance personnel.

Regards

Bull

Jul 29, 2008 | Washing Machines

3 Answers

My Haier HW-C1460TVE-U washing machine was installed this morning did the empty cycle first then did a load of towels worked perfectly did another wash Err code Unb came up. Got sprit level and checked...


Have been to one of these machines today. UNB will still show even if the machine is empty. I think the feedback amplifier on the main PCB is at fault. If I have any luck with it I'll post another message

Jun 29, 2008 | Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

544 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1460 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Brad Brown

Level 3 Expert

15557 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...