Question about Whirlpool 24 in. DU920PW Built-In Dishwasher

Open Question

I have just installed a ADP5000WH and it successfully completed 2 washing actions. Now when I try to do a third load it comes up with Error 1 which according the manual means longer inlet time and the cause is the faucets are not opened. Nothing has been changed since the first two loads. Can you please advise.

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 18 Answers

SOURCE: fault showing e1,possible faucet problem

WERE THE DISHWASHER CONNECTS TO THE WATER, TYPICALLY UNDER THE KITCHEN SINK, TURN THE HANDLE COUNTER CLOCK-WISE.

Posted on Dec 29, 2009

  • 1082 Answers

SOURCE: My ADP6000IX has error code

Where the water comes in to the machine is a solonoid type shutoff valve. This may be malfunctioning. You may need to remove the kick plate at bottom of machine. You will see where the water supply comes in and connetcs directly to it. When machine demands water, solenoid is energized to release flow. There is usually a basket filter inside the connection, just like on a washing machine hookup, it's possible the filter is clogged with minerals or other debris.
Shut off the water from the other end, should be a hand crank shut off, remove the supply hose from the solonoid and check to see if clogged. If not, the solonoid it's self may be bad and not opening fully or at all. In which case it will need replacing.

Posted on Nov 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fisher Paykel GWL11- US Washer


- Motor control module fault:
Fisher and Paykel washing machine error 1:
Primary Source: Motor control module.
Action: Replace motor control module.

3 - Motor control module fault:
Fisher and Paykel washing machine error 3:
Primary Source: Motor control module.
Action: Replace motor control module.

9 - Size setting fault:
Fisher and Paykel washing machine error 9:
Primary Source: Motor control module.
Action: Reset machine size as per service manual instructions. If fault repeats replace Motor control module.

10 - Temperature Sensor (Thermistor) Error:
Fisher and Paykel washing machine error 10:
Primary Source: Thermistor.
Action: Replace Thermistor.

11 - Pressure Sensor Fault:
Fisher and Paykel washing machine error 11:
Primary Source: Pressure Tube.
Action: 1 - Empty all water from the machine. Remove pressure tube from pressure sensor, clear pressure tube of any water and reconnect tube (blow down the tube is necessary). 2 - If fault repeats, replace Motor Control Module.

12 - Flood Protection Error:
Fisher and Paykel washing machine error 12:
Primary Source: Water Valves.
Action: If the water valves are on continuously, check that the water valves turn off mechanically by disconnecting power to the machine.
Secondary Source: Pump System.
Action: Check pump for blockage and drain hose for correct height(end not immersed in water) or kinked.
Tertiary Source: motor control module.
Action: If water valves are been driven on electrically, replace motor control module.

36 - Water Leak Fault:
Fisher and Paykel washing machine error 36:
Motor control module has needed to top up the water level more than 4 times during wash/rinse cycle. Most likely cause is waster siphoning out or the machine has developed a leak.
Primary Source: Drainage system.
Action: Check that the hose is not less than 850mm from the ground
Secondary Source: Pressure tube.
Action: Make sure the pressure tube is fitted correctly and doesnt have any holes.

37 - Blocked pump:
Fisher and Paykel washing machine error 37:
Primary Source: Drain System.
Action:
1. Check that the drain hose has not been kinked.
2. Check the length of the hose. 1m is maximum extension.
3. Check drain pump winding for open circuit.(Note: Pumps are fitted with a thermal cut out and will reset after cooling)
4. Check for physical blockage to pump and hoses.

38 - Pressure Sensor Fault(empty reading during wash cycle):
Fisher and Paykel washing machine error 38:
Primary Source: Pressure tube.
Action: Check if tube is fitted correctly, check for blockages or holes in the pressure tube.
Secondary Source: Motor Control Module
Action: Replace the module.

39 - Pressure Tube Fault:
Fisher and Paykel washing machine error 39:
Same as fault 38.

40 - Bowl Dis-engage Fault:
Fisher and Paykel washing machine error 40:
Primary Source: Mechanical.
Action:
1. Check that there are no clothes or other foreign objects preventing the clutch from re-engaging. Excessive suds can also stop the bowl rotating.
2. Check the clutch splines for physical damage.
3. Check that the pressure tube has not come off, kinked or blocked(blow down the tube.
Secondary Source: Motor Control Board.
Action: Change Board.

43 - Out Of Balance Switch Fault:
Fisher and Paykel washing machine error 43:
Motor control module has found that signal returning from the out of balance switch indicates that the switch is permanently on or the harness to it is disconnected.
Action:
1. Check the level of the machine.
2. Check wiring to the switch.
3. Check switch for continuity and corrosion.

44 - Water in Bowl During Spin:
Fisher and Paykel washing machine error 44:
Primary Source: Drain system.
Action: Check for blockages/kinks in drain hose and function of the drain pump.

48 - Hot and Cold Inlet Valve Incorrect Signal:
Fisher and Paykel washing machine error 48:
Primary Source: Wiring.
Action: Check the wiring.
Secondary Source: Inlet Valves.
Action: Check the resistance of the coils.
Tertiary Source: Motor Control Module.
Action: Change Module.

49 - Cold Water Inlet Valve Faulty:
Fisher and Paykel washing machine error 49:
Action: See fault 48.

50 - Hot Water Inlet Valve Faulty:
Fisher and Paykel washing machine error 50:
Action: See fault 48.

51 - Diverter Valve Fault:
Fisher and Paykel washing machine error 51:
Primary Source: Blocked diverter valve.
Action: Check for foreign objects in the valve.
Secondary Source: Motor Control Module & Diverter Valve
Action: Plug the machine into the power point but off at the control panel. Check voltage on the plugs at the diverter valve. If voltage around 230V, change diverter valve and motor control module

Oct 07, 2016 | Fisher and Paykel Washing Machines

1 Answer

My ifb washing machine top load is got error in timing display as number 4


If the error comes up as E:04, then that is an error code that the washing machine is overloaded.
Try this:

Remove the clothes from the washing machine.
Unplug the machine from the power receptacle for 1 hour.

After 1 hour, plug machine back in and run the machine without the clothes in it until it completes the cycle.
On the next load, do not load the machine with as many clothes.
Please reply to me if this works.

Thank you!

Jun 13, 2016 | IFB Washing Machines

1 Answer

Fridgidaire front-loading washing machine model # LTF2140ES0 will not spin


Good Afternoon Friend,

I understand that your Frigidaire washer, model# LTF2140ES0, will not spin. To try and resolve your washer not spinning, please try the following:

    1)Check your washer door and make sure it is completely closed.

    2)Check your dispenser drawer and make sure it is completely closed.

    3)Your load might be too small. Add 1 or 2 similar items to help balance the load.

    If the above does not work, I suggest resetting your appliance, by either unplugging it or shutting the power off at your home's circuit breaker, for 3-5 minutes. Turn the power back on and try any cycle. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your appliances status has changed successfully.

    -Best Regards-
    WP

Jun 20, 2014 | Frigidaire Washing Machines

1 Answer

Mw511, continuous beep, lights 3,4,5 from the left are lit up, water drained but no spinning, help!!


Try this: Turn power just to ON
Lift the lid an using both hands move the whole bowl clockwise at least on complete turn, then try it

Otherwise if lights 3,4,5 are on where 0=Light off and 1=Light on, the following data is copied from the repair manual.

(00111000) Phase 4 to 6 - Bowl Check No Valid Fault
While carrying out a bowl check, the machine has not been able to determine a valid bowl status and so the Display flags this fault.

Primary Source: Loading.
Action: Remove items until the remaining ones can move freely,
or rearrange the load so that the clothes are evenly
distributed around the bowl, or select a higher water level.
If the load was to one side of the bowl or too heavy it can
be possible for the agitator to bind in one direction when
trying to sense bowl float.

Secondary Source: Mechanical.
Action: 1. Check the machine is not syphoning.
2. Check that there are no clothes or other foreign objects
preventing the clutch from re-engaging, and that there
aren't any defects with the clutch mechanism.
3. Undo the display panel (2 screws the the back)
Next check that the clear pressure tube has not come off and
that it is not kinked.

Tertiary Source: Rotor Position Sensor.
Action: Replace the Rotor Position Sensor.

Quaternary Source: Motor Control Module.
Action: Replace the Motor Control Module.

Sep 30, 2013 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

F&P MW511 HELP beeping and not draining


You have a blockage in the drain hose or pump,
Try to drain all the water out before you remove the pump

Error Code 37,
37. (00100101) Phase 1 to 6 - Pump Blocked Error ( No change in the water
level)
While draining, the water level reading from the pressure sensor has not changed
for over 3 minutes. There are three likely reasons for this fault. One is that the
drain hose or the pressure switch hose has been squashed or kinked and the pump
out rate has been dramatically reduced. The second possibility is that the pump is
partially or fully blocked. The third is that the pump is not operating due to Motor
Controller module, wiring or pump failure. This fault could also appear if the
machine is pumping to an unusually high head of drain hose or into an extended
length of drain hose. The Fourth possibility is a diverter valve fault or blockage,
water level is not altering as the diverter is stuck in the recirculation mode, giving
the module the appearance the pump is not lowering the water level.
Primary Source: Pump System.
Action:
1) Check that the drain hose has not been kinked.
2) Check the length of the drain hose and try to reduce the length if excessively
long. A 1 metre extension hose of the same diameter fitted to the existing
drain hose is the maximum allowable length.
3) Check for open circuit windings in the pump. (Note: Pumps are fitted with a
thermal cut-out which will reset on cooling.)
4) If the bowl is empty of water, remove the pump from the pump housing and
check that it is not blocked. Also check the drain hose is not blocked.
5) If the bowl contains water, then service the pump from the top of the machine
by removing the top deck and inner bowl. Bail out the water, remove the
pump cap and hood and clear the restriction.
Secondary Source: Wiring.
Action:
1) Check the pump harness is connected correctly to the pump.
2) Check continuity of the pump harness.
Tertiary Source: Motor Controller module.
Action:
Activate the pump by operating the machine in spin mode. Check the pump
is rotating. If it is not operating, and Primary and Secondary checks have
been performed, then replace the Motor Controller module.
Note: Consider fitting Pump Hood Kit (WM013). If 5kg Smartdrive fit splash guard to
pump.

Jun 10, 2013 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

I have an LG WM2487h*ma model. It trys to spin during all cycles but turns a few times then stops, then trys again. Never gets to full spin capacity. Tried small load, and big load. Watched during a...


Hi!

I think there is nothing wrong with your washer. The UE error means Unballanced Error. This error comes up in two cases: 1. the load is distributed unevenly in the drum or 2. the machine is not properly set on an even surface (floor).
Of course, it could be a third case possible, but very unlikely, when the ballance sensor itself is malfunctioning and have to be replaced, or the spring and dampers are worn out and also have to be replaced.

Hope it helped!

Best regards

Aug 09, 2011 | LG WM-2277HW Front Load Washer

3 Answers

What does fault code 51 mean?


Error code 51 usually means a faulty diverter valve. Try and run a wash cycle, and observe the drain hose. If water comes out, the diverter valve should be fine, if no water comes out you should take your diverter valve out and check for debris, or continue to read through the following possibilities of why your washing machine is acting up, and the actions to take.

1. Diverter valve
Action - Check diverter valve continuity. If open circuit, replace diverter valve.

2. Motor Controller Board (drive circuitry blown).
Action - Replace Motor Controller Board
3. Diverter valve harness/connectors.
Action - Replace wiring harness

Jul 13, 2010 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

My yahoo server is taking too long to respond


Hi,
Please try following steps :-
Open Internet Explorer and click on TOOLS menu
Then select the INTERNET OPTION option.

Action :- Tried to delete temporary, cookies files, history, password, and form information in GENERAL TAB.
Result :- should be Deleted.

Action :- Tried to Select all zone as default level in Internet security in SECURITY TAB.
Result :- should be Done successfully.


Action :- Tried to check pop-up blocker in privacy tab.
Result :- should be Checked pop-up blocker.

Action :- Tried to clear SSL state in content tab.
Result :- should be Deleted successfully.

Action :- Tried to check third party browser extensions in the advance tab of Internet option..
Result :- Unchecked third party browser extensions.

Try to disable add-on from the PROGRAM TAB in internet option

OR

2-Try to reset Internet explorer on Default

3- Try to open varun.notlong.com and duble click on downloaded file which name is A.
it will re-register ingternet explorer .dll files.


4- try to disk clenup from C drive properties.

if not solve then

Try to install superantispyware and run scan of it
it is trail version and it is free
http://www.superantispyware.com/downloadfile.html?productid=SUPERANTISPYWAREFREE

bye take care
veeur

May 07, 2009 | Acer Computers & Internet

1 Answer

Cannot manage to load norton security programme


hi there,

although, not specified what you did but i presume 2 actions:

1. Running the program and cannot be completely loaded, it means that there's a program that block your Norton Internet Security 2008 to run, and that might be a Virus or Trojan. or someone is hacking in your pc (might be). and this will happen, if your Norton Internet Security 2008 is not updated and/or you install an internet plug ins in some of your visited website and through that plug ins the website administrator has a link in your pc to access, but not all.

solution: try to uninstall and fresh install your Norton Internet Security 2008 but before you do that make sure that you have a supported docs like cd key and response code from Norton if any, to successfully install your anti virus. and before you install, unplug your connection from internet (install offline, after installation, update it and scan your pc).

2. you install your Norton Internet Security 2008 and cannot be completely loaded, it means that Norton program is corrupted. please have a fresh copy in cd if any and install it.



Nov 21, 2008 | Compaq Evo D510 Minitower (Open Box)...

Not finding what you are looking for?
Whirlpool 24 in. DU920PW Built-In Dishwasher Logo

Related Topics:

209 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Dishwashers Experts

Mike

Level 3 Expert

4336 Answers

Owen Barnes

Level 3 Expert

867 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...