Question about Disney Cars Toon: Maters Tall Tales for Nintendo Wii

1 Answer

Cars game only has one player as an option, how do I open/unlock 2 player mode? Tried 1 and 2 on second remote, nothing happened.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Filmmaker:

    Uploaded 5 video answers.

  • Expert
  • 84 Answers

  • From the Disney/Pixar Toy Story Mania! opening screen, press the 1 button on Player 1 Wii remote to start.

  • At the "How many players?" (color palette) screen, point to the number of players (1 through 4) and press the A button.

  • Point to the desired color for each player and press the A button on the corresponding Wii remote. The player's number will be displayed in the color (for example: 1 in yellow, 2 in purple). Point to the green arrow and press the A button to advance.

  • At the name entry screen (Mr. Spell), starting with Player 1, point to the letters and press the A button to select. Once Player 1's name has been entered, point to "Enter" and press the A button to advance to the next player.

  • When all players' names have been entered, you may select from Story or Freeplay mode to begin playing. Freeplay mode will only contain games that were previously unlocked in Story mode. For more information on Disney/Pixar Toy Story Mania! game modes, see the game manual.
  • Posted on Mar 22, 2011

    • jlhepburn Mar 22, 2011

      Your step two is where my problem is, players 2-4 are covered, not selectable.

    • falconeray Mar 22, 2011

      Are you 100% sure that your wiimotes are connected to the wii console?


      Press the Power button on the Wii console to turn it on.
      Open the SD Card Slot cover on the front of the Wii console. Remove the battery cover on the back of the Wii Remote you wish to sync up.
      Press and release the SYNC button just below the batteries on the Wii Remote; the Player LED will blink. Quickly press and release the SYNC button on the inside of the SD Card compartment on the console.
      When the Player LED blinking stops, the syncing is complete. The LED that is illuminated indicates the player number (1 through 4).

    ×

    1 Suggested Answer

    6ya6ya
    • 2 Answers

    SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

    Hi,
    a 6ya expert can help you resolve that issue over the phone in a minute or two.
    best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
    the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
    click here to download the app (for users in the US for now) and get all the help you need.
    goodluck!

    Posted on Jan 02, 2017

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    I have a Samsung HTC 550 home theatre system. It's set to region one and I've tried everything to make it region free to no avail. I want to watch a region 2 DVD. Can you help??


    1. Open tray and remove any disks in tray.
    2. Close tray.
    3. Switch Off Player and unplug from power. wait 30 seconds (this clears RAM)
    4. Reconnect to power.
    5. Turn on player with remote.
    6. Press ENTER on remote. (ignore message on screen)
    7. Press 8, 4, 2, 6, 9 using keys on remote. (if your player is already set to region 2)
    8. Press ENTER on remote.
    9. Wait until player finishes processing. (approx 15 seconds)
    10. Turn off power from remote.
    11. Turn power back on with remote.

    Player is now Region Free.

    or

    Turn on with remote control without disc.
    When message "No disk" appears, press on the remote,
    ENTER,
    8,4,2,6,9
    ENTER,
    If hack work after the second ENTER player will power off automatic.
    When power on again this was region free, I can confirm now read region 1, 2 and 4.

    Sep 08, 2016 | Samsung HTC-550 DVD Home Theater System

    1 Answer

    Unlocking my DVD player


    some others

    new model pacific 1002mk2 (ASDA) using remote.;
    press open on remote
    press clear
    press 1-3-6-9 Then 0(for multiregion)

    Press close

    It's important to note that you will not see anything happen on screen or display!
    The buttons are small,so you'll have to be precise

    1. PUT A REGION 2 DISC IN PLAYER

    2. WHEN IT IS LOADING UP PRESS "SETUP"

    3. PRESS "7" FOR MULTI REGION

    4. PRESS "PAUSE/STEP"

    5. PRESS PREVIOUS " |> "

    6. PRESS SETUP

    YOUR PLAYER IS NOW MULTI REGIONAL.. IS YOU WANT TO SET THE REGION IN STEP 3 PRESS 1 FOR USA OR WHATEVER YOU REQUIRE....

    or

    switch on.on the remote press "open/close",0,1,2,3,open/close and it plays straigt away. but nothing is shown on the screen.
    or
    It's true - a quality DVD player from Asda for £59.95. Highly recommended. This 1359 hack worked with my Pacific 1002 purchased March 03.
    Note. There is no on screen display or any indication on the machine when entering the hack.

    Switch machine on and using the remote control only:
    1. Press 'open/close' button (the draw should be left open).
    2. Press the 'clear' button.
    3. Press '1'.
    4. Press '3'.
    5. Press '6'.
    6 Press '9'.
    7. Press '0' (zero for multi-region).
    8. Press 'open/close' button.
    End.

    or

    1. switch on dvd with remote (leave drawer closed)
    2. Press: setup
    3. press: 7 (note nothing will happen)
    4. press: pause/setup button (again nothing will happen)
    5. press: previous/I<< button (nothing will happen)
    6. press: Next/>>I button (nothing will happen)
    7. press: setup

    Dec 05, 2007 | Televison & Video

    1 Answer

    How to reset keyless entry remote on 2000 toyota celica.


    Begin with:
    The driver's door open and unlocked.
    Key out of the ignition.
    1.Insert and remove the key from the ignition switch 2 times within 5 seconds.
    Steps 2 and 3 should be performed within 40 seconds.
    2.Close and open driver's door TWICE.
    3.Insert the key into the ignition and remove it.
    Steps 4 - 6 should be performed within 40 seconds.
    4.Close and open the driver's door twice.
    5.Close the door.
    6.Insert the key into the ignition.
    7.Turn the ignition switch from "Lock" to "On" and back to "Lock" at about 1 second intervals to select the desired mode:
    1 time for ADD mode.
    2 times for REWRITE mode.
    3 times for CONFIRMATION mode.
    5 times for PROHIBITION mode.
    8.Remove the key from the ignition.
    9.To confirm your mode selection, the power locks will now cycle "lock" to "unlock" a number of times corresponding to your key cycles in step 7.
    If Confirmation or Prohibition modes have been selected, opening the door will complete the procedure.
    10.For Add or Rewrite modes do the following within 40 seconds of Door Lock confirmation:
    A.Press both transmitter Lock and Unlock buttons simultaneously between 1 and 1.5 seconds and release.
    B.Within 3 seconds of step A press the transmitter Lock button for more than 1 second and release.
    ^If the transmitter has been successfully programmed, the power locks will cycle "lock" to "unlock" once at this time.
    ^If there are problems with the transmitter or the procedure up to this point, the locks will cycle twice. If this occurs, verify that you have received the correct transmitter, and then repeat the above procedure.
    C.If multiple remotes are to be reprogrammed, repeat steps A and B.
    11.Open the driver's door to conclude programming mode.

    Sep 03, 2010 | Toyota Celica Cars & Trucks

    1 Answer

    How do I reactivate the wireless remote control transmitter for a 2004 Toyota Camry XLE? I replaced the battery and the transmitter still does not work.


    To Program Wireless Remote Transmitters:
    Begin with:
    The driver's door open and unlocked.
    Key out of the ignition.
    1.Insert and remove the key from the ignition switch 2 times within 5 seconds.
    Steps 2 and 3 should be performed within 40 seconds.
    2.Close and open driver's door TWICE.
    3.Insert the key into the ignition and remove it.
    Steps 4 - 6 should be performed within 40 seconds.
    4.Close and open the driver's door twice.
    5.Insert the key into the ignition.
    6.Close the door.
    7.Turn the ignition switch from "Lock" to "On" and back to "Lock" at about 1 second intervals to select the desired mode:
    1 time for ADD mode.
    2 times for REWRITE mode.
    3 times for CONFIRMATION mode.
    5 times for PROHIBITION mode.
    8.Remove the key from the ignition.
    9.To confirm your mode selection, the power locks will now cycle "lock" to "unlock" a number of times corresponding to your key cycles in step 7.
    If Confirmation or Prohibition modes have been selected, opening the door will complete the procedure.
    10.For Add or Rewrite modes do the following within 40 seconds of Door Lock confirmation:
    A.Press both transmitter Lock and Unlock buttons simultaneously between 1 and 1.5 seconds and release.
    B.Within 3 seconds of step A press the transmitter Lock button for more than 1 second and release.
    ^If the transmitter has been successfully programmed, the power locks will cycle "lock" to "unlock" once at this time.
    ^If there are problems with the transmitter or the procedure up to this point, the locks will cycle twice. If this occurs, verify that you have received the correct transmitter, and then repeat the above procedure.
    C.If multiple remotes are to be reprogrammed, repeat steps A and B.
    11.Open the driver's door to conclude programming mode.

    Sep 02, 2010 | 2004 Toyota Camry

    1 Answer

    Can't get my second remote to activate, and so only one player mode works.


    Hi,

    It seems your second remote has malfunctioned. There are 2 options at this point.

    1.) Replace the batteries and see what happens.

    2.) Send it in for a replacement controller (if under warranty)

    I hope I helped!

    Apr 12, 2010 | Nintendo Wii Console

    1 Answer

    I bought a new Keyless remote for a 2007 Forester from a Subaru Dealer to replace an original one that went bad after 2 years. I have followed the directions in the owner's manual to program it, but can't...


    IMPREZA: 2005, 2006, 2007 and
    FORESTER: 2005, 2006, 2007, 2008
    Check for Immobilizer key on Forester XT models only.
    information is always subject to change and correction imp05keylessremote1.jpg
    new remote for 2005 Imprezas.
    This is not the same remote as the 05 Legacy/Outback remote which also has truck/gate release on the front and a red panic button on the back.
    Lock: press Lock button for 2 seconds or so to lock car, and arm optional security system. The car with chirp once and turn signals flash for locked, 5 short chirps and signal flashes if any door is not fully closed. The dome light goes on for 15 seconds and ignition key ring (if present) will light for 30 seconds when unlocked.
    Unlock: press unlock one time for driver's door, press again within 5 seconds to unlock all doors inkling rear gate (wagon). The system does not open the trunk.
    Panic mode: press and hold lock button for approx. 3-4 seconds to activate Panic mode. I panic model the horn honks and turn signals flash until either the lock or unlock button is pushed again.
    Finder mode: Press lock button 3 times within 5 seconds to activate Vehicle Finder mode. The horn will honk once and the turn signals will flash 3 times
    Distance: works within approx. 30 feet depending on battery strength, nearby concrete walls and etc.
    Audible Chirp On-Off: the system will chirp when locked or unlocked. To turn OFF the chirps, unlock the door and then push both lock and unlock buttons at the exact same time for 2+ seconds. There will be 2 chirps indicating the the audible is off. To turn the chirp back on, repeat the process and the system will chirp one time when it is back on.
    Battery: as the battery ages it will only work as you get closer to the car. When a battery is replaced, the transmitter must be re-synchronized with the Keyless control unit. To synchronize, press the lock or unlock button 6 times.
    Programming: 4 codes may be programmed.
    Sit in driver's seat and unlock all doors. Open and close the driver's door
    Turn the ignition key from LOCK to ON position 10 times within 15 seconds. Be sure to stop at both lock and on. The horn will HONK once to indicate transmitter programming mode is activated. Leave key in LOCK position and don't remove it from ignition.
    You now have 45 seconds to complete the programming as below.
    Open and close driver's door again.
    Push either lock or unlock button on the remote you want to program. The horn will honk 2 times when successful.
    To continue and program other remotes at the same time: open and close the driver's door and push lock or unlock on the remote. The driver's door must be opened and closed between each remote you want to program.
    Done programming? remove the key from the ignition and the horn will honk 3 times.
    DELETE old codes? Reprogram 4 times, it will overwrite old codes.
    Alarm Security System: optional on all models. When locked there is one chirp (can be turned off, see above), the turn signals will flash and the red 'security' light will start to flash once every 2 seconds except for STi which flashes twice every 2 seconds.
    There will be 5 chirps if a door, hood, and trunk or gate is not fully closed
    You can also arm the system by using the power lock button on the driver or passenger door as you get out of the car and then closing the door behind you.
    Disarm the system: push unlock for 2 seconds
    Lost remote, alarm activated? When you can't use a remote to turn off the system: open the door with a key or try to start the car and the horn will start to honk. Turn the key on-off 3 times within 5 seconds and the alarm will go off and you can start the car. It's simple!
    VALET mode: To set valet mode or just to disable the security alarm system: 1. unlock all doors 2. physically open the driver's door 3. hold the UNLOCK button on remote for 2+ seconds. The red 'security' light will then flash 2 times a second until the car is turned on.
    System has been Tripped (except for STi): if you unlock the door with the remote and it chirps the signal light flash 4 times, the system has been triggered;
    Identification mode: To find out what happened and why the system was triggered:
    Open and drivers door, leave it open. Turn ignition key from LOCK to ON 2 times and then leave in LOCK position.
    Tripped code: 1 security light flash: a door has been opened, 3 flashes when the impact sensor was triggered, 4 flashes when the ignition was messed with or battery disconnected

    Nov 19, 2009 | 2007 Subaru Forester 2.5X L.L. Bean...

    1 Answer

    Nintendo Wii Cars game won't let us add a second player


    Another person on this site solved our problem, and THANK YOU! Here's how to do it:

    *Remove the back of the 2nd remote- if you've got the rechargeable battery pack, replace it with two "AA" batteries.

    *Open the little door on the front of the console and press the red button for about three seconds

    *On the back of the remote, inside the battery compartment, press the red button for about three seconds.

    *Press the "A" button on the second remote

    *You will need to do this for each remote you'd like to add, but it will unlock the "Multiplayer/VS mode and will not need to be 'refreshed'- just use the power button and/or the "A" button on the remote you want to play.

    If you want to use all of the tracks in both "Piston Cup" and "Road Courses" so that your racers can do more than one or two things, Do this:

    *Go to the main menue and choose OPTIONS
    *Go to CHEATS
    *Enter this code:
    IF900HP
    You'll need to use the + shaped button to do this.You'll can use this for one or multi-player modes but will probably have to do it every time you start up and you'll need to do it separately for each mode. This cheat code is good for single player as well.
    For all cheat codes for "Cars" (or any game) go to this URL:

    http://www.freewiicheats.com/codes/c/cars.php

    That site, along with FixYa.com, have opened our whole game. Thank you all. HAPPY RACIN'!

    Mar 22, 2009 | THQ Cars for Nintendo Wii

    2 Answers

    2 player?


    HEY We just found the answer on this site! Thanks!

    Take the back off the second remote.
    On the console, open the door and press the red button for about three seconds.
    On the back of the remote, in the battery compartment, press the red button for about three seconds.
    Press the "A" button on the second remote.

    This will unlock the multiplayer mode. If you want more than one additional player, do this for all that you want to add. Each time you start the game you'll need to press the "A" button for each additional player.

    Thanks again, and Happy Racing!


    Feb 06, 2009 | THQ Cars: Mater-National for Nintendo Wii

    2 Answers

    Unlock regional code for Sony DVP-NS575P


    1) Turn your DVD off. 2) Use the remote control and press: 
    - Display 
    - Top Menu 
    - Clear 
    - Power 
    This should power the device into Service Mode. 
    3) Choose option 2 and then choose option 4. 
    4) There should be two fields: Input Code and Current Code, each one with 5 chars long. 
    Type: 12450 
    Then push zero on all the 5 places of the first and the second field. 
    Push ENTER. 
    5) There should be a zero on the device display, meaning that all regions are free. 
    6) Press POWER to turn it off and you're done. 

    Let me know if it works!

    Dec 03, 2008 | Televison & Video

    1 Answer

    Need to change my Crown CDV 1100B player to multi region, have tried recommended options from other sites, but to no avail. This what I've tried so far. 1) Press set up 2)press 1369 (which was...


    a) Press SETUP button on the remote control to display the setup
    screen

    b) Press "1369<<<>" on the remote control ( "<" = left navigation
    button; ">" = right navigation button)

    c) A new item "VERSION" is added on the menu

    d) Select thr VERSION item and press SELECT button to enter

    e) Press the right navigation button ">" on the remote control to
    change the region code

    f) Press SETUP button again to exit the region code change mode

    Note: Region code 0 is "all region code".
    OR

    1.press eject to open the draw.

    2.type 9-8-1-7.

    3.press select to go through regions.

    4.change to region 9 for multi region.

    5.press eject to close the draw.

    OR

    1. Press the Open/Close button on your remote control to open the drive tray

    2. Press the 8, 4, 2 and 1 buttons on your remote control, in order, one at a time

    3. Press the Enter button on your remote control until the hidden menu appears

    4. Select 1 for region 1, 2 for region 2, and so on, or All for multi-region

    5. Press the Open/Close button on your remote control


    To alter the Macrovision settings on this player

    1. Press the Open button on your remote control to open the drive tray

    2. Press the 4, 5, 6 and 1 buttons on your remote control, in order, one at a time

    3. Select Enable to enable Macrovision, or Disable to disable Macrovision

    May 03, 2008 | Televison & Video

    Not finding what you are looking for?
    Disney Cars Toon: Maters Tall Tales for Nintendo Wii Logo

    294 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Disney Video Game Consoles & Games Experts

    James Wishart

    Level 2 Expert

    122 Answers

    Dan Shibata
    Dan Shibata

    Level 3 Expert

    542 Answers

    kakima

    Level 3 Expert

    102366 Answers

    Are you a Disney Video Game Console and Game Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...