Question about Kenwood KDC-MP208 Car CD/ MP3 Player

1 Answer

How Do I Set My Clock on My Kenwood KDC-MP208?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 116 Answers

1:- Select Clock Adjustment mode Press the top or bottom side of the Control knob. Select the "ClK ADJ"/ "ClCK" display. 2:- Enter Clock Adjust mode. Press the centre of the Control knob for at least 1 second. The clock display blinks. 3:- Adjust the hours. Press the top or bottom side of the Control knob. Adjust the minutes Press the right or left side of the Control knob. 4:- Exit Clock adjustment mode, Press the [B.BOOST] button.
Now whats the time, Gotta get my tea.
Regards, Dave

Posted on Mar 20, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Technician can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Technician (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have kenwood car mp3 mp208 how i set clock?


See page 11: http://www.kenwoodusa.com/UserFiles/File/Global/Consumer/Manuals/kdcmp238.pdf

Mar 14, 2011 | Kenwood KDC-MP208 Car CD/ MP3 Player

1 Answer

Kenwood kdc-mp208 stuck in ''protect'' mode....


Protect indicates that there is a short or a grounding problem usually within the speakers2_bing.gif or the speaker wiring. Locate and press the reset button (pinhole). If protect comes back then disconnect all speakers, reset and connect them back one at a time until protect shows up again. This will help you find out where the unwanted DC signal is coming from. If protect shows up when all speakers are disconnected, then it may need service.

Apr 10, 2010 | Kenwood KDC-MP208 Car CD/ MP3 Player

1 Answer

Set clock on kdc-mp208


Here's the owners manual for your KDS-MP20, from the kenwood-usa site:

http://kenwoodusa.com/UserFiles/File/Global/Consumer/Manuals/kdcmp238.pdf

The following is found on pages 10 and 11 of the manual:

1. Enter Menu mode
Press the [B.BOOST] button for at least 1 second.
"MENU" is displayed
2. Select the menu item
Press the top or bottom side of the Control knob.

"CLK ADJ" can only be performed when in Standby Mode

----------
Manual Clock Adjustment

1. Select Clock Adjustment Mode
2. Press the center of the Control knob for at least 1 second
-the clock display blinks
3. Adjust the hours
Press the top or bottom side of the Control knob.

Adjust the minutes
Press the left or right side of the Control knob.
4. Exit Clock adjustment mode
Press the [B.BOOST] button.

----------
I hope that helps.

Mar 27, 2010 | Kenwood KDC-MP208 Car CD/ MP3 Player

1 Answer

How to set the clock


there should be a button labeled menu. press this button for a few seconds and it should take you into menu mode. use the fm/am buttons to scroll through the menu until ;you reach clock, the press the seek up or down button until the display starts flashing. use the am/fm and seek buttons to set the hour and minutes. press the menu button again to leave the menu.

Oct 29, 2009 | Kenwood KDC-MP208 Car CD/ MP3 Player

1 Answer

No remote wire?


On the remote wire of the stereo always be a blue one

Aug 16, 2009 | Kenwood KDC-MP208 Car CD/ MP3 Player

1 Answer

Kenwood KDC-MP208 Clock Set


Make sure that the source is set to "Standby" when trying to access the menu. It took me about an hour to figure it out and afterward I felt like a ******.

Apr 09, 2009 | Kenwood KDC-MP208 Car CD/ MP3 Player

2 Answers

Kdc-mp208


This is usually ground problem. check ground wire

Feb 14, 2009 | Kenwood KDC-MP208 Car CD/ MP3 Player

1 Answer

I recently purchased a kenwood KDC-MP208 and am having difficulty setting it to display the time.


First, set the clock if it isn't already set. You need to get your cd player into standby mode and then hold the "boost" button. This should get you into a menu. Use the up and down pad to scroll through the options until you find "clock" hold the center button to get into the mode, to set the clock. Once in use the up and down, left and right pad to set the time. Then press the menu button to get out. Press the source button to get back into a normal mode, then hold that "boost" button again. This should bring you into a different menu. scroll through the menu until you see "display" and you should be able to choose to display clock in there. I hope I didn't steer you wrong. Let me know if you need further help. Good luck
-Andrew Hawkins

Sep 04, 2008 | Kenwood Car Audio & Video

Not finding what you are looking for?
Kenwood KDC-MP208 Car CD/ MP3 Player Logo

210 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4885 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

yadayada
yadayada

Level 3 Expert

77194 Answers

Are you a Kenwood Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...