Question about Husqvarna Garden

1 Answer

I have a 16 in 235 Husqvarna chainsaw that starts find and runs for a few minute. then acts as if it is not gettting enough fuel as it starts to bog down while running and will not maintain idle.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Husqvarna Master
  • 2,239 Answers

It may well just need the carb adjusted, unfortunatley there is a special tool required the adjust the screws, the L screw on the carb may need richening up, so if you manage to get the tool unscrew it by 1/4 out ( anti cliock wise ) tool part no. 530035560

Posted on Mar 21, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

346XP Husqvarna chainsaw acts like its seized then after a few minutes turns over fine and starts.whats wrong?


It has run too lean for a while and the piston and rings are damaged. The piston is probably picked up and grows with heat enough to partially seize when hot, frees off when it cools down. It needs a new piston and rings set. If you are lucky the bore is not too badly damaged and may go again with a new piston. When/if you get it fixed make the mixture (air:fuel) richer and check you have enough oil in the fuel.

Sep 18, 2014 | Garden

1 Answer

Stihl 028 chainsaw runs good for awile then bogs and dies


Check fuel filter, fuel tank vent and possibly clean carb and replace carb diaphrams

Feb 12, 2014 | Stihl 028 Chainsaw Crank & Case

1 Answer

Chainsaw cranks and runs but after minute or two it dies. will start again but dies when trying to throttle up


Check the fuel tank vent. Does the saw leak fuel when laying on its side.? Faulty vent can cause the saw to bog down when running

Nov 20, 2012 | Husqvarna Garden

1 Answer

My saw runs good at idle and mid rang but when I stick it into a large limb and try to cut it bogs down and will die if I don't let go of the throttle. It acts as if it is starving for fuel. I tried to...


I have had to change a few fuel tank breathers on the 455 and 460 saws, when it starts to die try to slacken off the fuel filler cap, if it picks up again it is a brather issue, the breather is under the starter cover at the top right hand corner.

Sep 25, 2011 | Husqvarna 20" 60cc Rancher Chain Saw 460

1 Answer

My husqvarna chain saw will start fine and run good and cut good for a few minutes then it will start running fast then slow down run fast slow down it will do that 3 or 4 times then cut off any idea...


It certainly sounds fuel related, remove the fuel hose from the fuel tank and replace the filter on the end, try the machine again, if it is no better it could well be an issue with the fuel tank breather, to test this run the saw until the problem starts to occur, slacken the fuel cap enough to allow air into the tank, if the machine picks up and runs well you will need to replace the tank breather, let us know if this works and i will will go through how to change the breather.

Feb 09, 2011 | Husqvarna 350 18 Inch Gas Chainsaw 52CC...

1 Answer

Saw runs great then bogs down 20 sec. after i start cutting i let off it runs good then bogs again when cutting after a few sec


Check your air filter, if clean chances are your carburetor needs to be rebuilt. the carburetor has thin diapragms that get hard and won't meter the fuel in fast enough.

Jan 30, 2010 | Husqvarna 965142201 K750 5HP 12" Gas Cut...

1 Answer

Runs great for 30 sec. to 1 min. then dies slowly


Is it your chain saw Husqvarna 40?

Try carb adjustments H-3/4 turn ,L-2 turns and T a little higher
I presume that compression and ignition sistem is adequate for the engine to run.Good luck

mihai

Apr 04, 2009 | Husqvarna "Chain Saw - 16" Bar, 3 Hp

2 Answers

Husqvana 61 chainsaw starts but cuts out after a few seconds


Are you pumping the primer till it's full of fuel? The fuel pump diaphram is only strong enough to keep things flowing after you have pumped it up. you will need to prime it up again if you run it out of fuel or if it sits any length of time

Mar 25, 2009 | Husqvarna Chain Saw 20" Bar

Not finding what you are looking for?
Garden Logo

Related Topics:

394 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Garden Experts

Phil Walker
Phil Walker

Level 3 Expert

605 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Are you a Husqvarna Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...