Question about Kenmore 24622 Top Load Washer

1 Answer

How to access the motor compartment - Kenmore 24622 Top Load Washer

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 19 Answers

A sledgehammer is the preffered method when dealing with a Kenmore.

Posted on Mar 20, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the rear heater motor located on 2008 uplander


If the van has E59 on the RPO sticker you have to remove the left rear lower trim panel to access the motor. If it does not have E59 just remove the left rear compartment lid and compartment to access the motor. RPO E59 is a power left sliding door.

Sep 24, 2014 | 2008 Chevrolet Uplander

1 Answer

Where is the blower motor resistor located?


It is under the dash accessed behind the glove compartment. If I recall, there is a screw securing it and a plug attaching it to the wiring harness.
Gain access by pushing in the sides of the glove compartment that allows the door to lower out of the way.

May 28, 2014 | 2006 Ford Freestyle

1 Answer

Can't get glass tray to move


REplace the turntable motor. The compartment is in the bottom of the oven. Open a small compartment and you can access the motor.

Jan 10, 2014 | Kenmore Microwave Ovens

1 Answer

Not hot air whn control is moved to hot


PLEASE DON'T FORGET TO RATE!

Removal & Installation
  1. Disconnect the negative battery cable.
  2. Lower the glove compartment door to provide access to the recirculation duct assembly.
  3. Disconnect the vacuum hose from the end of the vacuum motor and the motor arm retainer from the door crank arm.
  4. Remove the two nuts retaining the vacuum motor to the recirculation duct, then remove the motor.
To install:
  1. Position the vacuum motor to the fresh air/recirculate door crank arm, position the motor to the recirculation duct and install the two retaining nuts.
  2. Install the retainer on the door crank arm.
  3. Connect the white vacuum hose to the vacuum motor, connect the negative battery cable, then check the operation of the vacuum motor.
  4. Close the glove compartment door.

Oct 25, 2009 | 1994 Ford Taurus

1 Answer

Where is a blower motor in a 1991 ford taurus


it's mounted inside the heater box.open glove compartment and 'unclip' sides to access 6 screws holding ductwork to box.disconnect vacuum line. lower duct to access & remove blower wheel..remove 4 motor mounting screws.install in reverse order.

Oct 18, 2009 | 1991 Ford Taurus

1 Answer

Blower motor access for replacement


Should be on the firewall under the hood or under the glove compartment. Depending on which engine you have in that car.

Jun 03, 2009 | 1993 Oldsmobile Cutlass Supreme

2 Answers

Can't get starter out of motor compartment


NOTE: Some Toyota models have an access plate in the fender well to facilitate starter service. Check for such an access point before beginning starter service.

  1. Disconnect battery ground cable. Remove battery, battery tray and/or igniter bracket, if necessary.
    1. Disconnect electrical connectors from starter motor.
    2. Remove air cleaner assembly, if necessary.
    3. On models with automatic transmission, remove transmission oil filler tube if necessary.
    4. Remove starter motor attaching bolts, heat shield (if equipped), then the starter motor.
    5. Reverse procedure to install.

Jun 01, 2009 | 1988 Toyota 4Runner

1 Answer

Cant access motor compartment


Those screws are hidden under the plastic that you press to make the cord retract.The way I get into that area is to pry it up from the side of the cord retract panel.They take a fair amount of leverage to get it off but it is straightforward from there-Good Luck,

Oct 20, 2008 | Kenmore 25512/ 25513 Progressive Canister...

2 Answers

Evap fan not working


you must remove baqck panel from bottom of freezer compartment, there you can access fan and other freezer components, check for open defrost thermostat as well.

Mar 30, 2008 | GE GDS18LBR Bottom Freezer Refrigerator

Not finding what you are looking for?
Kenmore 24622 Top Load Washer Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Sal DeAngelo

Level 3 Expert

2122 Answers

fordexpert

Level 3 Expert

5495 Answers

Mike Carew

Level 3 Expert

969 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...