Question about Office Equipment & Supplies

4 Answers

Regarding Bull Safes model :BSD1E. The beep sound and the error message were displayed. I changed batteries, nothing any change. I do not know how to reset. The door of the safe cannot be opened. What shall I do for this problem. Or how can I get user manual. Thank you.

Posted by on

  • 1 more comment 
  • massi_usa Mar 22, 2011

    Thank you for your answer.

    I checked a instruction for the electronic lock as you sent me, but our safe does not have "#" key.

    Just "start" button, could not do anything.

    And also I could not find any key hole even behind key pad.

    The safe picture on a instruction is little different than ours.

    Model is same but no black belt.

    I attached our safe.

    I think my safe is old ??

    Bull safes/Blue Air Inc in Gardena, CA is manufacture?

    Is there technical support ?

    Thank you

  • massi_usa Mar 24, 2011

    Regarding Bull Safes model :BSD1E.

    I would like to open asap.

    Please help.

    Thank you.

  • massi_usa Mar 24, 2011

    I'm asking about Safe not FAX.



4 Answers

  • Level 1:

    An expert who has achieved level 1.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Contributor
  • 1 Answer

Just cracked my own i found in auction. Gimme a shout if your problem is still a problem. 612-224-0707 Travis
Regarding Bull Safes model :BSD1E.

The - 5_19_2016_6_16_59_pm.jpg

Posted on May 19, 2016

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 3,018 Answers

Do to the nature of this item there will be no manual that will solve your problem. You will have to contact the manufacture and give them your information and they will have to assist you. Click this link and go to the bottom of the page. It is their contact information. Phone, address, web address. Safes get stolen from time to time and it would be a real security issue if a simple manual told people how to open or reset the safe they just stole.
Regards, Tony

Posted on Mar 25, 2011


  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 17,970 Answers

We dont know details about your device, so, try to look tin this site:

Keep us updated.

Posted on Mar 24, 2011

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,140 Answers

Hello there,

The instructions for the electronic lock can be downloaded from here:

You should be able to open the safe using the master/over-ride key. The lock is hidden behind a removable plastic cover between the keypad and the handle. Please download the instructions then let me know if you need further assistance by clicking on "Add a Comment" below your question.

You will need to have Adobe Reader installed on your PC to open the instructions:

If you don't have the master key or you've locked it inside the safe (never do this!), you will probably need to contact Bull Safes / Blue Air Inc. on 1-310-808-3102 for a replacement key. You will need to provide proof of purchase.

Hope this helps.


Posted on Mar 20, 2011

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

No display problem for intel D865GSA board

What are you formatting ? Have you changed the RAM. Does tour system work in its original configuration ? You do not say what the pattern of the beeps is. Before the display disappears, is there a message sent to the screen ?
From the manual

Whenever a recoverable error occurs during POST, the BIOS displays an error message

describing the problem (see Table 53). The BIOS also issues a beep code (one long

tone followed by two short tones) during POST if the video configuration fails (a faulty

video card or no card installed) or if an external ROM module does not properly

checksum to zero.

An external ROM module (for example, a video BIOS) can also issue audible errors,

usually consisting of one long tone followed by a series of short tones. For more

information on the beep codes issued, check the documentation for that external


There are several POST routines that issue a POST terminal error and shut down the

system if they fail. Before shutting down the system, the terminal-error handler issues

a beep code signifying the test point error, writes the error to I/O port 80h, attempts

to initialize the video and writes the error in the upper left corner of the screen (using

both monochrome and color adapters).

If POST completes normally, the BIOS issues one short beep before passing control to
the operating system.


Apr 18, 2014 | Intel 865G Motherboard

1 Answer

IBM Thinkpad T41 beep sound on system startup

Here are the beep codes for the Thinkpad:" Continuous beeping System board failure One beep; Unreadable, blank or flashing LCD LCD connector problem; LCD backlight inverter failure; video adapter faulty; LCD assembly faulty; System board failure; power supply failure One beep; Message "Unable to access boot source" Boot device failure; system board failure One long, two short beeps System board failure; Video adapter problem; LCD assembly failure One long, four short beeps Low battery voltage One beep every second Low battery voltage Two short beeps with error codes POST error message Two short beeps System board failure.

Dec 26, 2012 | Dell Optiplex GX620 Pentium 4 3.4GHz (Open...

1 Answer


I have had zero success in finding out any information about various models of electronic safes--no manufacturers' website, no online manuals, etc. Many of these safes are imported from overseas manufacturers.
Dead or dying batteries is a common problem, and I gather that many models of safes come with an override key.
It is incredible how many people have found the best place to keep their override keys and/or instruction manuals is INSIDE their safe!
I ask that anyone with owner's manuals or instruction sheets please publish them on this website for the benefit of others, but that is unlikely as they aren't the ones seeking information--they already have it!

I would suggest to you that you take the beeping and flashing light as a warning that your batteries are low. Open the safe while you still can, and change the batteries as soon as possible.
Sorry I can't be of more help!

Nov 11, 2011 | Locks & Locksmithing

1 Answer

Beeping when you start it up

The memory stick may have gone bad. Try changing the memory. A faulty memory will cause the computer to beep while the booting starts.

May 12, 2010 | HP Pavilion TX2000Z 12.1" TOUCH-SCREEN...

1 Answer

Cmos battery change then nothing!

You may need to clear the cmos in order to fix that, here is a link regarding the procedure.

Post your results here, especially if this doesn't resolve your issue.

Apr 02, 2009 | HP Computers & Internet

2 Answers


are u getting any beep message ? let me know the model and the beep tone that you get, if you don't get any beep try changing ram if you have VGA card installed try changing that.

Dec 06, 2007 | Compaq Presario SR1000T (568657) PC...

1 Answer

Canon G5 Lens error message

Defective mechanism, a stucked mechanism is present. camcorder are smart it can detects error and shuts down itself for safety. earlier models dominoes the defect if the user is not quick enough to react when something goes wrong with the camera. You need professional service to fix it.

Nov 07, 2007 | Canon PowerShot G5 Digital Camera

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

1,916 people viewed this question

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts


Level 3 Expert

102366 Answers


Level 3 Expert

7993 Answers


Level 3 Expert

75817 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides