Question about Integra DTR-7.1 Receiver

1 Answer

Integra DTR 7.8 - front panel display not operable. All other functions OK. Any way to repair myself ?

Posted by on

  • jzargo Mar 20, 2011

    YES - it was a long shot,but I really knew that.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,157 Answers

Hi Jzargo,

I would just like to ask if your system's display on the front of the unit wont light up? If the unit appears to be working fine but just no display, it might caused by defective resistor in the display. If your system is still in warranty, I recommend to have the service center replace the defective resistor in the display for free.

Hope it helps.

Thank you for using FixYa.

Posted on Mar 20, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My integra av receiver model no DTR-70.1 amplifier displays but no sound what could be the problem?


http://www.integrahometheater.com/faqs.php Check the connections and try a master reset?
Perform a master reset. To do the reset you need to turn the receiver on, then on the front panel of the receiver press and hold the "VCR/DVR" button while doing that press the "STANDBY/ON" button. You will see the word "Clear" in the display screen and the receiver will go into standby mode.

Jul 03, 2018 | Integra Audio Players & Recorders

1 Answer

I am not getting any audio (sound) out of my Integra DTR 4.6. Any suggestions?


Does the vu meter show anything(bars moving up and down when audio is present?If so you may have a blown fuse or bad IC in the amplifier section causing the problem. If there is no indication of audio on the front panel it would be a Microprocessor problem

Oct 15, 2014 | RCA Onkyo Integra Dtr-4.6 Av Receiver Wrat

2 Answers

I have a DTR 7.1 Integra receiver and it goes into protect mode when turned on. Is this something that can be fixed by myself or does it need to go to repair shop.


If you have a volt meter you may try and repair it yourself. First however disconnect the speakers and see if the set still goes into protect. If so you may have shorted output and drive transistors. There will be open resistors near them as well. You can compare the bad channel with a nearby working channel since normally only channel shorts out at a time. Always replace outputs in pairs since they in push pull configuration .

Oct 02, 2014 | Integra Dtr-7.1 Av Receiver Surround Sound...

1 Answer

Integra 7.8 display bad


The bad resistor is on the ps board that drives the display, well on mine at least. The resistor is supposed to be 10 ohms at 1/8 watt "i think" i replaced it with a 1/2 watt resistor. Either way its R9310. the board is right behind the display on the right side just behind the volume knob. when open and looking from the back you see it just fine. it's not hard to get out. fairly simple to fix. integra-7-8-display-bad-otccdugj0mk41z1tpuysbqy4-5-0.jpg integra-7-8-display-bad-otccdugj0mk41z1tpuysbqy4-5-2.jpg

Jul 20, 2014 | Integra Dtr-7.8 Receiver

2 Answers

How to fix Integra 7.8 display is dead


They will be value of 10 ohms or less in the secondary power supply attached to the front assembly

Jul 20, 2014 | Integra Dtr-7.8 Receiver

1 Answer

"handshake" between DTR 5.9 and an LG Blu-ray player


You will have a defective processor pcb. You may want to see if you can get Integra to give you a one time repair on this.

Mar 26, 2014 | Integra Onkyo Rc-711m Dtr-4.9 / 5.9...

1 Answer

Integra DTR-5.6, no sound for am/fm tuner


reset receiver if that does not work You will have a defective processor pcb

Aug 24, 2013 | Integra DTR 5.6 Multi Media Amp

1 Answer

How do I set up an Integra DTR 7.8 for 3D display and audio


Your DTR-7.8 receiver is not 3D compatible. It does not support the new 1.4 HDMI. You have to have 1.4 HDMI and 1.4 cables for the 3D format.

You can bypass your receiver for the video though. Simply run your HDMI cord (1.4) from your Blue Ray to your Projector. Your audio can be ran from your Blue ray to your reciever.

May 17, 2012 | Integra Audio Players & Recorders

1 Answer

I am missing the remote for an Integra DTR 5.3 receiver/amp. I have a Sony RM-AV3100 Universal Remote that I want to program to control it. Does anyone know where I can find the 4 digit remote code that...


Hello
Sony RM-AV3100 remote has no codes to setup with any Integra devices. You have to try its code search method. Sometimes you may find a code. But not sure. Go to the user manaul of that remote. There is proceedings for code search process. The codes are four digits indeed. OK.

Oct 09, 2011 | Integra DTR-5.1 Receiver

Not finding what you are looking for?
Integra DTR-7.1 Receiver Logo

Related Topics:

295 people viewed this question

Ask a Question

Usually answered in minutes!

Top Integra Audio Players & Recorders Experts

The Knight
The Knight

Level 3 Expert

75774 Answers

Rob Villi

Level 1 Expert

49 Answers

Michael Galve
Michael Galve

Level 3 Expert

1269 Answers

Are you an Integra Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...