Question about Washing Machines

1 Answer

Hi i have a Hotpoint WMF740 Aquarius washing machine which had a F-05 error which i have hopefully fixed. now the lcd display is saying f-09 error what do i need to do now.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 6,277 Answers

Hi from retired Englishman in SW France,
For the F05 presumably you found and cleared/cleaned the drain filter ;-0)
F09 is rather a more difficult problem as it decodes as an 'incorrect or faulty EEPROM'. I presume you have tried disconnecting power and reconnecting again? If you have I'm afraid it will need an engineer to fix ;-0( Sorry, John C

Posted on Mar 20, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Washing machine not selecting cycles. It is stuck on fast wash, dial moves but wont click and select any other cycle.

the problem is the shaft on the control knob
is cracked so the knob turns but won't grip
the shaft on the control panel
requires an new knob

Jun 06, 2016 | Hotpoint Washing Machines

1 Answer

Hi my hotpoint Aquarius wmf740 dial is just spinning no clicks is there an easy fix

try to tighten the screw using a small screw driver or try to pull the knob and give some paper packing and fix it then rotate the knob to the desired position

Dec 10, 2014 | Washing Machines

1 Answer

Could someone email me the fault codes for a hotpoint aquarius wmf740 washing machine please

Hi I see you need the Fault Codes for your Hotpoint Washing Machine

See this link for the info since I do not have your E-mail to send the details I have created this link for your viewing regarding your concern.

Hope this helps.

Oct 02, 2012 | Hotpoint Washing Machines

1 Answer

Hotpoint aquarius wmf 740 has error code h20

Just had same problem with my hotpoint wmf740 showing h20 and found an easy fix was to clean out the detergent draw thoroughly and just behind remove tray was easy and it does say to do this regulary in the manual

Jul 16, 2012 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

Hotpoint aquarius fault code f 05

  • F05 - Pressure switch jammed on full
  • Thing to do check pump is not blocked and clear it then reset machine by unplugging for 5 mins and plug back in if still gets error F 05 then you need a repair call out. hope this helps.

Jan 08, 2012 | Hotpoint Washing Machines

1 Answer

I have fault code F06 on my Hotpoint WMf740 machine, what does this mean?


F6 error is apparently a motor fault. The
motor could be jammed, open circuit ,
burnt out. It may just be a broken wire
or connection come off. Check the motor.

Dec 13, 2010 | Hotpoint Aquarius WD640 Front Load...

1 Answer

My aquarius wmf740 has a blockage cannot undo the white water release valve on front bottom right hand side of washer to solve problem. Any help grateful.

tip machine right back and unscrew valve. It is probably caught on something. Hope this helps ( I had a kirby stuck in mine)


May 21, 2010 | Hotpoint Aquarius WMA42 Front Load Washer

1 Answer

The machine won't start as saying door isn't

1.the door may be worn at the point it presses the switch at 2.the door switch may be wired incorrectly 3.the door switch may be worn out and needs to be replaced

Mar 06, 2010 | Washing Machines

1 Answer

Error message F-01 & flashing lights etc I have a Hotpoint aquarius, WMF740. Suddenly returning to the kitchen I noticed an error message - the machine was switched off - which says F-01 and flashes...

Error code F01 indicates a short circuit motor triac.
You need to check connections on the motor, the motor plug and the module.
Having said that, you really should ring the manufacture, as the washer is still obviously under guarantee, and should be fixed at no cost to you.
The point to bear in mind is that if you do anything to it yourself, then in theory, you could invalidate the guarantee.
So, unless it is anything obvious, then I would advise you ring the manufacturer.
Hope this is of assistance to you.
Please rate my solution.

Dec 21, 2009 | Hotpoint Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

287 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers


Level 3 Expert

81285 Answers

Brad Brown

Level 3 Expert

17431 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides